Roofing Felt (Aluminum covered) Consist of a polyester fleece, impregnated by oxidized bitumen .The exterior side is covered by an aluminum layer and the inner side by nylon ,the aluminum layer reflexes more than 85% of heat and protects the main layer of the roofing felt against ultraviolet ray. This product is a very good cover for buildings roof . Roofing Insulation (Normal Isogum) Consists of a polyester fleece and a fiberglass tissue layer, which are impregnated by bitumen The exterior side is covered by mineral powder and the inner side by nylon. It is suitable to insulate roofs, kitchen, floors, baths, building foundations, swimming pools and cisterns.
0C/-5C/-10C App membranes available with various thickness, weight and elongation performances. Shrinked pallets
Chqistex tm e-ptfe porous membrane combine high flow rate and high filtration efficiency, enabling high rates of airflow while remaining impermeable to water, aerosols, and particles. Features: 100% pure p.T.F.E. 0.2 to 5um reference pore size Wide range of air flows Hydrophobic Unaffected by common chemicals, ph range 0-14 Low friction High porosity with superior air permeability property
G-textm is 100% polyester continuous filament needle punched non woven geotextile. It has been characterized by high strength, maximum width (6.6 m) and uv resistant itself without inhibitor. It is resistant to commonly encountered soil chemicals, mildew and insects, and is non biodegradable. Thickness[astmd5199]ú¿2kpú¬ Mm 1.2 Roll width M(ín) 6 Roll length M(í²) 340 Approx load qí»ty per 40í» hq Sq. M 65, 280
A kind of three dimensional structure new-type geosynthetical material suitable for protecting water and land soil, can effectively water and land soil flowing away, increase greenland of measure of area, improve living environment. Usage: Can instead of conctete, asphalt, stone and other slope protection material, mainly apply to slope of road, railway and river lane.Dams and dikes, mountain slope, ete . Can prevent land soil from water and rain erosion before grass covering grows. Can bear sourcing of high water space and high-speed water after grass covering grows. Can reduce cost of construction by a width margin, cost is only / concrete, / stone. Adopt mactomolecule material and anti-uv rays stability, its chemical chatacter is very stable, no pollution to environment. Easy construction after surface of land is smooth. Operation: Can use bamboo pole or wood stick pass the whole roll net mat when construction, then pull net mat along slope, use wooden nail or plastic nail to fix four circle of net mat, distance between nails is cm, one square meter has nails. Length of nail from land surface is usually cm, add nails on loose land, length of nail on up slope is longer than on down slope when construction on high slope. Pay attention to keep netting mat smoothly and add nails on sudden change place topography. Check carefully conneeting .Length of conneeting is cm, nail must be fixed in connecting place, nails, density is added %, there is no internal and keep net mat closely on up net mat, width of bore diameter on up nail is two times of netting mat hole, so can suppress on vertical direction. Depth of sowing takes actions that suit local circumstance, chose long root and suitable for local climate of grass seeds.
Woven gcotextiles: Is used for soil separation, stabilization and reinforcernent applications including, paved and unpaved roadways , airport runways and taxiways and roads at waste containment facilities woven geotextiles help save on aggregate placement and repair costs associated with constructing and maintaining unpaved roadways.Characterized by soft subgrades, hith traffic loads and large deformation tolerances, typical unpaved roads often requite upkeep.Asoft subgrade covered with the appropriate woven geotextile stabilizes an access or haulroad by spreading applied loads over a wider foundation, reducing rut depths and preventing aggregate contamination by the underlying subgrade soils.This reduces mainten ance costs, improves roadway life and permits unrestricted flow of traffic.
Non-woven geotextile is widely used in seepage prevention, inverted filter, drain, isolation and other items in highway, railway, water conservancy and other projects.
We can supply high-quality geomembrane that meets gm13 and gm17 international standards, ldpe thickness is between 0.2 and 3.0mm, with from 4 to 10m.Hdpe thickness can be from 0.3-3.0mm with width 4-10m.And we also supply the pvc and eva produce according to customers requirement. As following, we only introduce the hdpe geomembrane for examples.
Wire mesh covered with zinc and pvc Firm structures, flatsurface, corrodion-fesisting and oxidation-resistant.It is used for breeding chken, duck, goose, rabbit and also used as fencing in zoo, machinery equipmentí»s protection, speedwayí»s feecing, standiumí» to pursenet, the virescence belt protection mesh on the road.If we use the mesh to make container whose shape is like a box, then fill the container with rip rqp, it could be used for protecting and holding out the sea wall, hillside, bridge and other related retaining wall civil engineering, it is the superior material for floodcon troll and fighting a flood
The products are made by soaking the base in bituminous or thermo plasticity elastomeror thermoplastics modified bitumenous, then covering double faces with elastomer(SBS)or thermoplastics(APP,APAO,APL)modified bitumenous, and last finishing the upward face with fine sands, mineral slates(or grains)or polythene membrane while downward face with fine sands or polythene membrane. 100mm*10m
Asphalt compound embryo flexible waterproofing Product synopsis: The compound embryo flexible waterproofing volume material is take the polyester felt - grid cloth or the adhesive-bonded cloth - grid cloth as a carcass of tire, uses rubber resin, assistant and so on modified the asphalt to make the dip coating material, on the surface turns round may the curl laminated shape waterproofing material which by the polyethylene membrane, the granulated sugar, the mineral piece (grain) isolation materials and so on material or aluminum foil makes. Product execution country JC/T690-1998 "Asphalt Compound Embryo Flexible Waterproofing Volume Material" Characteristic Uses the compound carcass of tire, is advantageous in the improvement product performance, enhances the mechanical strength, the enhancement waterproofing performance; Has the wide temperature sector, serviceable; Uses compound carcass of tire, this kind of product low-price quality merchandise, and is durable. Applicable scope But widely uses in each kind of domain and the type project waterproofing, most is suitable for the below project type: Industry and civil construction roofing project waterproofing, including: Non-on person roofing, on conventions and special roofing project and so on person roofing, heat preservation roofing, non-heat preservation roofing, planter roofing, roof parking lot, inversion roofing; Industry and civil construction understructure work waterproofing, moisture-proof as well as construction and so on indoor swimming pool, fire basin waterproofing; The subway, the tunnel, the concretes lay the road surface the bridge floor, the sewage treatment field, trash to bury municipal engineering waterproofing and so on field; Water conservancy facilities waterproofing and so on canal, basin. Specification Breadth: 1000mm Thickness: Divides into 3mm and 4mm Area: Each beginning integral should not be 10m2 (3mm, 4mm). Physical mechanics performance Gusu the asphalt compound flexible waterproofing volume material physical mechanics performance achieves JC/T690-1998 "Asphalt Compound Embryo Flexible Waterproofing Volume Material" the standard request, its physical mechanics performance sees the next table.
KT series polyethylene suffers the polypropyle Product outline The KT series polyethylene suffers the polypropylene fiber high polymer compound waterproofing volume material is by the polyethylene class synthesis high polymer material waterproof layer, the increase assistant, provides for old age the level, the enhancement to increase the tacky surface and the polypropylene fiber adhesive-bonded cloth primarily the new waterproofing material which becomes after the automatic production line processing. * this product high and low surface roughness, the adhesive-bonded cloth textile fiber assumes without the rule overlapping structure, forms three-dimensional mesh, suits many kinds of material agglutinations, especially with cement material in solidification process direct agglutination, so long as does not have Mingshui then to be possible to construct, its overall performance is good, the tensile strength high, easy to cake, the friction coefficient small may suppose directly in the sandy soil uses, the stable property is reliable. Is one kind non-toxic, the non-pollution green environmental protection product. * this product is suitable for the industry and the civil construction roofing and the basement waterproofing, moisture-proof, separates was mad that the room inner wall, the ground are moisture-proof, bathroom waterproofing, water conservation pond storehouse, channel, arch of bridge waterproofing, anti-seepage, waterproofing and so on metallurgy chemical industry against pollution. Technical process Approves and sweeps clear the basic unit - - configuration adhesive (along with to use along with configuration) - - the node spot (masculine and feminine elements angle, eaves, to fall spots and so on drainage opening, pipeline hole) the extra ply construction - - waterproof layer construction - - waterproof layer approval - - protector construction.
The products are made by soaking the base in bituminous or thermo plasticity elastomer(such an styrene butadiene styrenef¼SBS),or thermoplastics(such as atactic Polypropylene---APP,APAO,APL)modified bitumenous, then covering double faces with elastomer(SBS)or thermoplastics(APP,APAO,APL)modified bitumenous, and last finishing the upward face with fine sands, mineral slates(or grains)or polythene membrane while downward face with fine sands or polythene membrane. good self heating, easy application, and long service, etc.
Colored polyurethane underwater paint Product outline This product is colored. Non-tar double component green environmental protection underwater paint. The cold construction craft simple service convenience may carries on the construction under the normal temperature to the even roofing and each kind of structure complex spot. Whole Cheng Moxing good has rubber elastic elongation ratio the best pupil without the joint to be able to adapt the basic unit crack and the distortion. The cementation intensity high applicable scope is broad. But is welcoming the water to use by Shui Chushi is 1 level of waterproof ideal material. The service life long bears the period of five days to bear the aging, to bear the greasy dirt and certain acidproof alkalinity stable property service life may amount to above 20 years. Mainly uses in the roofing, side the subsurface construction, the ground construction and the building hit and the joint. Material amount used Generally each square meter needs 2-2.7kg thickness 1.5-2mm. to divide 3-4 coating, time coating wants evenly consistent. High and low spreads blows the direction to do alternately in any case. Each time the time interval decides general by the construction ambient temperature and the paint film solidification degree many in 24 hours. Does not stick take feel as the standard. Stick an adhesive-bonded cloth or the Bolivian filament cloth according to the design requirements also coca coating either the multi-layered middle shop are better. Paint film protection In order to lengthen the waterproof layer the service life to guarantee the project quality. On the person roofing makes the cement mortar protector on the paint film when the last paint film has not solidified. Scatters 2-3mm the granulated substance or the stone chips favors the paint film and the protector cementation.
J-match polyester insulation batts description: R-value: 3.5 Fiber dia.: 17.8~ 47.8ª8m Temperature: - 44 ~ +100íµ Thickness: 10~200ía2mm Percentage of moisture ín0.5% Hydrophobic rateí²98% Moisture rate each cubeín0.1% Wrvú+0.20md/cm2 Permanent set after compressed ín2% 45ípburning: difficult to burn Thermal conductivityín0.034% w/m. K Not toxic-gas during burning, doní»t drip 16pcs/pack, Pe package after vacuum compressed/
Tearing Strength: KN/m no less than 25 Standard Export Packing
1. Specifications: Length 1000mm+-5mm Width 330mm+-5mm Appears externally the length 142mm+-5mm Each square meter institute needs the tile 7pieces Packing pack/21pieces 2. The mineral: High-quality bitumen, coated on both sides on a carrier layer of Heavy glass fiber forms the main component of the guttate bitumen shingles. The Bitumen mass gets spread and fastened owing to the glass fiber; Moreover, the fiber increases the deformation resistance and stability of the shingles. A colored mineral granulate is used for the uppermost covering layer. 3. The characteristics: Shingles can be easily laid, because they are easy to lay and to cut. The bitumen shingles perfectly fit any roof form (dormer windows, round) and are ideal for neatly covering difficult corners and edges (ridges, crests, grooves, xxxxx). Even in new constructions and renovations, more and more shingles are used nowadays. What is of interest here is that in the course of a renovation of your roof, you can easily re-cover the roof according to the latest trends in the desired shingle colors and shapes, taking into consideration the minimum roof angle. 4. Color reference: Water black ash, jujube brown madder, desert gold, the deep shade is green, the snow chrysanthemum is white old tree brown, the forest is green class lime, wu tanhui, asia is red. size:1m*0.333m/pc 1.5kg-2.0kg/pc
Available with different reinforcement of polyester, glass fiber or compound reinforcement. Obtained modifying a distilled butumen, they have an extremely high elasticity. PE film, fine sands, or mineral slates are used as finishing surfaces. Specifications: Thickness available: 2mm, 3mm, 4mm Width: 1m Length: 7.5m, 10m, 15m It may be applied by cold or hot-melting method with easy application, featuring no pollution and long service life. In a wide application, such as basements, toilets, ponds, civil and industrial roofs, car parks, bridges, swimming pools, tunnels and refurbishment of bitumen roofs etc. It is specially suited to use in the cold area and buildings with frequent structural movements. 1m*10m/roll
These water based peelable coatings which have been developed first time in india. Dry film acts as temporary protective coating . Film will be crystal clear, transparent, and elastic. It can be easily peeled off when desired. All these water based peelable coatings are used as a protective coating for name plates, aluminium & brass labels, S.S. sheets , stainless steel surfaces, glass, acrylic, mirror, plastic fabricated items, watches, dials, clocks, glazed tiles, laminated photos & posters, dome labels, photo frames, washing machine, refrigerators, ovens, cooking range bodies, steel sinks, sanitary ware, geyser bodies, sunmica laminates, aluminium doors & windows, cupboards, pressure cookers & non-stick ware, helmets, automobiles, two wheelers bodies and parts, anodized coloured aluminium doors & window frames, F.R.P. Products, solar panels & equipment, bath tubs, wrought iron furniture, computer plastic bodies etc. It is also used as a paint mask. Non-toxic, non-hazardous, non flammable, eco friendly coatings Our range / series of peelable coatings and their sub grades as per product end useage :- 1) Kleairpeel (water soluble film after drying - can be peeled off when required) 2) Easipeel (water resistant film after drying - can be peeled off when required) 3) Propeel (water proof film after drying - can be peeled off when required) but still under R&D for better perfection in the product in this series. All above products are Water Based Liquids , ready to use and are Air Drying. They can be applied by a Hand Roller, Painting Brush, Regular Spray Gun or a Roller Coating Machine in accordance to the product selected. All the equipments can be washed with water after the work is over. All Coatings dry in about 20-30 minutes depending on the external temperature. A minimum dry film thickness of 100-150 microns is required for perfect peeling and protection. Some products require a minimum curing time of 12-24 hours (according to weather conditions) for perfect film formation before it is peeled off. Depending on the product selected for use all the dry films will have different degree of water resistance in Dry film. Forced drying by mild heat (35-45 deg C for a few minutes) will accelerate the curing, thereby reducing the curing / drying time. When removing the film start from one corner and peel off carefully and slowly away from the protected / finished surface. Minimum size 32 kgs Carbouy packing.
Excellent adhesion to clean, dry, plywood and concrete. min 300-400 gr/sqm,max 800gr / sqm for each coat Application with brush,spray or roller - 3 / 12 / 25 kg buckets
