Sintered Titanium Frit well suited for use in Electrolyzers. These frits have a smooth, porous surface (80 micron filter rating) that gives good support for membranes. A much finer surface than our Expanded Titanium Mesh, this product is recommended to be placed against the membrane when designing higher pressure electrolyzers ( 20 psi). Custom sizes are available upon request. Titanium Foam Frit Specifications: Raw Material: Titanium Filter Rating: 80 Micron Thickness: 1.5 mm Working Temperature: 300 C Membrane Filtration Corrosion resistance Why not use a Carbon based Gas Diffusion Layer in an Electrolyzer Carbon based GDL materials will be consumed and converted into CO2 gas in the presence of the Oxygen ions and Voltage found on the Anode (Oxygen) side of the electrolyzer. This secondary reaction of oxidizing the Carbon in the GDL will give temporarily lower electrolysis voltage, but this is a short lived phenomenon. The carbon GDL is quickly consumed, resulting in poor compression in the stack, and thus high resistance and lower performance. You can still used carbon cloth or carbon paper material on the Hydrogen side (cathode) since there is oxygen on that side that will oxidize the GDL material.
Pure titanium processing parts have high titanium content, good plasticity, easy processing and forming, and good stamping and welding performance. It is resistant to corrosion in the atmosphere, ocean, and other conditions. Pure titanium processing parts are mainly used in aircraft skeletons, ship pipes, valves, pumps, heat exchangers, distillation towers, coolers, ion pumps, and compressor valves. In the industry, Ta1 is generally required for high formability, Ta3 is used for wear resistance and high strength, and Ta2 is the most widely used in general. Product parameters Product Name: Titanium Processing Parts Material grade: TA1 TA2 TC4 TA9 TA10 TA15 TC11 Executive standard: GB/T, GJB, AWS, ASTM, AMS, JIS Process state: Annealed state (M) hot working state (R) cold working state (Y) (annealing, ultrasonic flaw detection) Surface treatment: Sandblasting surface bright surface Product use: Aerospace equipment, petrochemical, shipbuilding, automobiles, watch accessories, etc. Features High-quality material selection Professional processing Fine workmanship Special customization The characteristics of titanium 1. It has a low density, a high strength, and a high specific strength. Titanium has a density of 4.51g/cm3, which is 57% that of steel, less than twice that of aluminum, and three times stronger. Titanium alloy has the highest specific strength of any regularly used industrial alloy. Titanium alloy has a specific strength that is 3.5 times that of stainless steel, 1.3 times that of aluminum alloy, and 1.7 times that of magnesium alloy. As a result, it is a necessary structural material in the aerospace sector. 2. Excellent corrosion resistance Titanium's passivity is dependent on the presence of an oxide film; its corrosion resistance in oxidizing media is far superior to that in reducing medium, and fast rate corrosion can occur in reducing medium. Titanium is not rusted in some corrosive environments. 3. Excellent heat resistance Aluminum typically loses its initial high mechanical qualities at 150 C, stainless steel at 310 C, and titanium alloys retain good mechanical properties at around 500 C. When the airplane achieves 2.7 times the speed of sound, the surface temperature of the aircraft mechanism hits 230 C, and the aluminum alloy and magnesium alloy can no longer be used, while the titanium alloy can. Titanium has a high heat resistance, making it ideal for turbine disks, aeroengine compressor blades, and aircraft rear fuselage skins.
Titanium GR5 plate.
Titanium plate.
Titanium plate.
GR1 grade porous titanium sintered plates.
Titanium plate.
Gr5 titanium carbide plate.
Titanium plates.
Titanium fin tube,copper fin tube,titanium tube,coppre tube,stainless fin tube,stainless tube.
Titanium bars, titanium plates, pipe fittings, equipments, targets.
MMO coated anodized titanium anode plate for electrolysis.
Titanium billets, plates.Turnkey service that includes certificates, transportation, logistics, manufacturers, distributors, OEMs
Titanium sheets and plates.
Titanium bars and plates 99.57 purity.
Product Introduction Sintered titanium felt is a kind of porous material created from tiny titanium fibers that have been flattened down and annealed to provide a smooth, flat surface ideal for use in a variety of industrial applications. This unique material has a range of features that make it ideal for use in a wide range of applications. In the production of hydrogen and fuel cells, sintered titanium felt is used as a Liquid/Gas Diffusion Layer (LGDL) in stacks, where it helps to distribute the reactant gases and provide electrical contact between the catalyst layer and the bipolar plate or current collector assembly. The material´s high corrosion resistance, even under highly acidic and humid conditions, makes it an ideal material for use in these applications. Parameters Material: Titanium Size: 1500 1200mm Fiber size: 20 microns-40 microns Thickness: 0.20mm, 0.25mm, 0.40mm, 0.60mm Porosity: 60%-75% Porosity and size can be customized. Features Porous structure: Sintered titanium fiber felt has an excellent porous structure, which provides high filtration efficiency and large dirt holding capacity. Thermal conductivity: The material has strong thermal conductivity, making it an ideal material for use in high-temperature applications. Precisionandaperture control:Sintered titanium fiber felthas precise precision and aperture control, which makes it suitable for use in applications where precise filtration is necessary. Corrosion resistance: The material has high corrosion resistance, even under highly acidic and humid conditions, making it ideal for use inharsh environments.
Medical titanium plate, medical titanium bar.
Titanium Bars And Plates.
Gr5 titanium carbide plate.
Titanium sheet & plate.Manufacturer
