Wagon Drilling Rig

Wagon Drill Rig

Rocker34 wagon drill rig Rocker34 is designed for drilling blast holes with dth hammer. Rocker34 has crawler for the difficult ground conditions, strong construction, easy maneuver capability. MAST AND FEED SYSTEMFeed Length4,1 m13 ft Feeding Force0 - 27 kN Pulling Force47,5 kN Drilling Angle22° - 90° POWER UNITBrandDEUTZ TypeF4L912 Number of Cylinder4 cylinders Cylinder Volume3,7 lt Power51 kW - 70 Hp Rev.2300 rpm Engine TypeDiesel CoolerAir HYDRAULIC SYSTEMFirst Pump160 bar27 cc /rev. Second Pump130 bar19 cc / rev. Auxiliary Pump180 bar19 cc / rev. Hydraulic Oil CoolerAir2024 K - 0,110 kW - 12 V ROTARY UNITSpeed133 rpm Toruque1185 Nm SUPPORT JACKSMovement UnitTrack / max speed 2,9 km/h Leverages of Jacks2 units of Hydraulic Leverages Cylinder Stroke150 mm m Weight2.830 kg ADVANTAGES

Vdd5 wagon drill rig (rubber whell driller) Technical characteristics General information Engine38 kw Weight2180 kg Feed frame Length5, 00 m Stroke4, 10 m Push force0 - 25 kn Pull force50 kn Drilling Drill speed0 - 120 cm/min (it may change due to ground.) Drilling diameter2, 5'' - 4'' / 63 mm - 102 mm Drilling depth50 m Rotation unit Drive engine75 rpm Torque1000 nm Oil cooler2024k – 0, 110kw – 12v Fuel tank capacity70 liters Oil tank capacity250 liters Advantages Vdd5 has hydraulic pull and push force. Vdd5 works with dth hammer. Vdd5 is moving with 3 wheel hydraulic traction. Vdd5 can be controlled with electrical joystick. Three wheel traction system of vdd 5 can be chosen as demanded. (only front, only back or free) Vdd5 is manufactured with high quality materials to maintain power and lifetime. Vdd5 provides easier and faster drilling with enhanced pull and push force and rotation. Vdd5 has a large volume of oil tank and oil cooler; therefore, the oil is used more efficient and long time. Vdd5 can drill 76, 89, and 100 mm of hole sizes. Vdd5 can drill with giving from 22 degrees to 90 degrees of drilling position. Vdd5's drilling vibration is minimized with the help of balancing pistons. Özanadolu sitesi 682. Sokak no: 25-27 Ývogsan-ankara-turkey tel: +90 312 394 47 24 faks: +90 312 395 62 07

Down The Hole (DTH) drill rig capable of drilling to a depth of 300mtrs (1000 ft) under favorable drilling condition. The drill rig can be operated on rocky formation and hard to medium soil formation. The drill rig can make a hole of diameter 4 to 6.

The drilling rigs can fully meet the well-drilling- process requirements by adoption of flexible driving designs- mechanical drives (high-speed diesels, hydraulic transmission box, angle gear box or middle-speed diesel hydraulic transmission, chain combination box), compound transmission and electrical drives (VFD or SCR) etc. * The whole unit is very compact and a quick whole transportation and installation of the whole drilling rig can be realized due to a utilization of a skid-mounted structure. In addition, the drilling rig requires a small working site due to its high integration and compact configuration. * Masts and substructures have various structures, such as: perpendicular-hoist sectional mast, whole-hoist K-type mast, telescopic substructure, spirally hoisted substructure and folding - frame substructure. * A standard and module design and various ways of combination have been adopted in order to boost up the universal and exchangeable performances of the drilling rigs and to meet the user different requirements. * Disc brake or band brake can be applied as main brake and air brake or FDWS brake can be used as auxiliary brake and the energy-consumption braking can be available for electrical-drive-rig auxiliary brake. The drawworks can be equipped with bit-feed motor and control system. * The Internet and communication techniques have been used on the drilling rigs, which can realize an integral display for power, air control, hydraulic control, and monitoring and the intellectual and safe control of the driller. * The perfect configurations of the solid control system, well control system, high-pressure pipe manifold system, the generator house, the engine pump house, doghouse and other auxiliary facilities can meet the user different requirements. Safety and inspection measures are strengthened under the guidance of the design concept of ° Humanism Above All¡± to meet the requirements of HSE.

1.High drill head lifting force; 2.Suit to various drill tools; 3.High hoist lifting force; 4.High drill efficiency; 5.Adaptable to various strata; 6.Rinse medium can use both mud and air. As per customers' requiremnt

ESSOS Series is Mud Drilling,DTH Water well Geo thermal drilling Micropiles Soil investigationsGround consolidations. Engine Unit [ Cummins QSB4.5 Tier III] - Aspiration : Turbocharged and Charge Air Cooled - Fuel System : Bosch Electronic - Emission Certifi cation : U.S.EPA Tier3,EU StageIII - Horsepower : 130 BHP [97kW] @ 2,200 RPM - Peak Torque : 459 lb-ft [622Nm] @ 1,500 RPM Mast - Box frame using high strength steel (Tensile 760MPa, Yield 700MPa) - Welding condition AWS D1-1 - V-Profi le power head sliding mechanism - Dual leaf chain with safety wire rope or telescopic cylinder type - Double Clamp(HI-ROKTM) equipped on Mast for angle drilling job - Equipped with 3,000lb winch - Power head stroke 12~14 feet - Power head side shift to give 8� clearance - Mast sliding stroke : 30� - Pull back : 28,000 lb ~ 40,000lb - Pull down : 17,000 lb ~ 28,000lb PowerHead - Two Speed Power Head - Strong and compact helical gears - Separate Water Swivel easy maintenance - Separate Float Cushion Sub - Max Torque : 3,523lbf-ft~5,576lbf-ft - Motor Speed : 20~122rpm - Eaton VIS series Two Speed Motor.

The draw works is driven by two VFD AC motors with 1+1r/2+2r step-less speed, and reversal will be realized by ac motor reversal. The mud pump is driven by VFD AC motors, which are mounted on the rear skid of mud pump, with v-belt transmission and simple structure. The independent driven rotary table runs with 1+1r/2+2r step-less speed, and reversal will be realized by ac motor reversal. Using AC-DC-AC drive technology, rotary table and draw works are four quadrant running and full digital vector control. Single drum, gear driven and one / two shifts smooth speed change draw works is simple in structure and reliable in operation. Feed back / dynamic brake is adopted to replace eddy current brake as auxiliary brake. Automatic drilling is obtained by draw works main motor or an independent motor. Intellectual position control for traveling block prevents crown block and rotary table from collision. Real time communication and network is available by using profibus technology. K type mast is suitable for install top drive system. Sling shot or swing up substructure and mast are applied so that all the equipment can be installed at lower position. Suit for any transportation.

Model : C650D-EXP blasthole drill Specifications: Rated capacity : Nominal hole size 7-7/8(200 mm ) by Rotary method, Upto a depth of 148 (45.12 m) using 30 long 6.25 OD drill pipes. Standard mounting : Tengl, India make Under Carriage model T23/D4 , 24 Triple grouser track 10 6 long with 9 bottom rollers and 2 carrier rollers each side. Independent hydraulic motor with Planetary gearbox drive for each track. Propel speed is 3.0 KMPH on plains and 1.5 KMPH on grades. Gradeability up to 25% grades with Mast down. Pulldown and hoist :Pulldown is achieved through twin hydraulic cylinders and roller chain arrangement. 33 head travel for handling 30 long drill pipe. Pulldown capacity: 35,000 LBS. Hoisting capacity: 20,000 LBS. Standard feed rate: 14 FPM Standard hoist rate: 25 FPM Fast feed rate: 70 FPM Fast hoist rate : 124 FPM MAST : Electrically welded square and rectangular steel mast of robust construction to withstand adverse drilling conditions. Mast is raised and lowered by two hydraulic cylinders with safety check valves. Working height of mast 38 for 30 long drill pipe. ROTARY HEAD : Axial piston hydraulic motor driven top head drive through spur gear reduction with a constant torque of 48,000 Inch-pounds at 0-150 RPM infinitely variable speed. AIR COMPRESSOR: Screw compressor with a capacity of 900 CFM at 100 PSI. Air oil receiver, Oil cooler, Oil filters and safety valves are provided as standard. PRIME MOVER: Cummins India make engine NTA 855C running @ 1800 RPM drives compressor @ flywheel end and hyd. pumps @ front PTO. Fuel tank capacity : 750 lit. DRILL PIPE HANDLING: Hydraulically operated Four pod loader suitable for handling 6.25 OD x 30 long drill Hydraulic power breakout wrench and stem wrench are provided as standard. HYDRAULIC SYSTEM : Open loop hydraulic system for propel, rotation, feed, Fan, auxiliary and pilot circuits. Axial piston ,variable volume pump: 48 US GPM at 4700 PSI for tram circuit and at 4200 PSI for rotation circuit. Axial piston pump : 12 US GPM at 2500 PSI for feed circuit. Gear pump for ROC fan : 22 US GPM at 3000 PSI for ROC fan circuit and 15 US GPM at 2000 PSI for auxiliary circuit. Hydraulic oil reservoir with suction strainers and 10 micron return line filters. Relief valves in all circuits. LEVELLING JACKS : Three hydraulic jacks - one front 140 MM bore, 48 stroke; two rear 125 MM bore, 36 stroke equipped with heavyduty telescopic guide tubes and lock check valves for safety. OPTIONAL EQUIPMENT: Centralised Lubrication system Shock sub for rotary head Rotary Deck Bushing Hyd powered winch Electronic depth counter Automatic Power breakout system Fire detection and suppression system Fast fuelling system Retractable dust curtain Water injection system with water tank.