Coatings
Optical Filter
Optical Window
Whenever light passes from one medium into another medium with different optical properties, most notably refractive index, part of the light is reflected and part of the light is transmitted. The intensity ratio of the reflected and refracted components is a function mainly of the difference in refractive index among the materials, the polarization of the incident light and the angle incidence.
Whenever light passes from one medium into another medium with different optical properties, most notably refractive index, part of the light is reflected and part of the light is transmitted. The intensity ratio of the reflected and refracted components is a function mainly of the difference in refractive index among the materials, the polarization of the incident light and the angle incidence.
As light passes through an uncoated glass substrate, approximately 4% will be reflected at each surface, this result in a total transmission of only 92% of the incident light. Coating each component will increase the throughput of the system and reduce hazards caused by reflections traveling backwards through the system (ghost images).
Optical coatings are often us ed to alter the reflectance, transmittance, absorbance, or polarization properties of optical components. The components being coated are usually called the substrates. The coating layer is deposited in high vacuum using the process of evaporation by either e-beam, or IAD(Ion Assisted Deposition). Coating materials include metal such as Au, Ai, Ag, Cr, etc. And semiconductors such as Si, Ge.
BARILAC barrier coatings are the most suited sustainable solution to replace polycoated laminated board, waxcoated, PVDC coated etc all non sustainable alternatives. Barilac barrier coat is recommended for paper cup, trays, foodtrays, pizza boxes, ice cream cartons etc. The special product features are. - Low COBB - Good oil and grease resistance - Good Moisture Vapour Transmission rate - Good heat sealing performance - Good water resistance - Low odour - FDA compliance
Epoxy Finish Paint is two-component, polyamide adduct cured, General Purpose Air drying Epoxy Coating. Its Excellent substitute to Enamel.
Water Based Coatings - Primers, Gloss & High Scuff - High Gloss/High Slip - Duct Gloss & Matt - Specialty Coatings - Soft Feel / Satin / Neutral / Super Matt
PC natural 100% pure pc without any coating MATERIAL: PC natural 100% pure pc without any coating CATEGORY: PC TYPE: Natural SPECIFICATION: Separate 25 kg bag and Mark per month 78 mt 100% pure pc without any coating ,post Industrial materials Origin: Bangladesh LOADING WEIGHT: 24 Ton FOB (USD/Ton): 1450$ - 1700$ Packaging: Jumbo Bag Est. Shipping Time: 15, 30, 45 days Our Commitment We are committed to delivering in accordance with the quality given, source and licensed in the field of scrap transportation. 2Lians always for the purpose of satisfying customers on the criteria of sustainability and fairness through high work efficiency
DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.
Two component, acrylic aliphatic polyurethane coating. Offers excellent gloss and colour retention. It is used for subtracts as steel, aluminum, glass-fiber, plywood etc.
PU Paints
Emulsion Paints
Primer
Use of Product : Coating, Paints, Offset Printing Ink, Plastics, Textile Printing Emulsions. TESTING MACHINES : 1. Muller Machine 2. Vibro Shaker 3. Melting Point Apparatus 4. Electronic Balance / Single Pan Balance 5. Laboratory oven Heating Mentle 6. Hegmann Gauge. We carry our application Test for : a) Textiles. b) Oil Paints. c) Water based Distemper. d) Inks : Ink testing done in NC Media, Polymide Media, Vinylamide Media. This Plant is dedicated for manufacturing the product â??Pigment Violet â?? 23â??. Location of Plant is at Lote Parshuram, Tal. Khed. The plot of the Company is in the area of MIDC and it is a Chemical Zone. There is a Central Effluent Treatment Plant, which does a secondary treatment of the Effluent before the water is released to near by Sea.
