ULPSM-O3 968-005 Ultra-Low Power Analog O3 Sensor Module DESCRIPTION
Quickly integrate Ozone sensing into your system with very low power consumption and a simple analog sensor signal output.
The ULPSM converts the Ozone sensor??s linear current signal output to a linear voltage signal, while maintaining the sensor at its ideal biased operation settings.
ULPSM-O3 968-005 Ultra-Low Power Analog O3 Sensor Module BENEFITS
* 0 to 3 V Analog Signal Output
* Low Power Consumption < 45 uW
* Fast Response
* On-board Temperature Sensor
* Easy Sensor Replacement
* Standard 8-pin connector
ULPSM-O3 968-005 Ultra-Low Power Analog O3 Sensor Module APPLICATIONS
* Fixed Industrial Safety Monitoring
* Portable Industrial Safety Monitoring
* Portable Personal Safety Monitor
* Indoor Air Quality Monitoring
* Outdoor Air Quality Monitoring
* Air Purification Control
ULPSM-O3 968-005 Ultra-Low Power Analog O3 Sensor Module PERFORMANCE CHARACTERISTICS
* Measurement Range: 0 to 20 ppm
* Lower Detection Limit: 0.3 ppm
* Resolution: 0.15 ppm
* Accuracy: < ± 2 % of reading
* Response Time T90: < 30 seconds
* Power-On Stabilization Time: 60 minutes recommended
We Can Supply Freestyle Libre 2 Flash Glucose Monitoring System Sensor Please Dont Hesitate to Contact Us in Case of Any Interested
Supplier: Wireless charger, batteries power bank, dust sensor, optical disc drive, tof, lidar, ar glass
Power Modules are Point of Load (POL) DC-DC converters integrating controller chips, chokes and I/O capacitors into a single power management package for step-down(buck) applications. The low profile and compact size enables significant saving of board space, high efficiency enhances application performance, and design structure allows automated assembly by standard surface mount equipment
For price, specification and other details please contact us
Supplier: Wired magnetic door sensors.
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
AC to DC converter battery charger 150-1000VDC rectifier 120KW power supply Product Introductionï¼? SANDI AC/DC Charger is specially developed for DC chargers. It has high efficiency, high power factor, high power density, high reliability advantage. AC input 3 phase, DC output voltage range from 150 to 1000VDC can be set, compliant with CE safety requirements, EMC standard EN61000-6-3 and EN61000-6-1 Class A, it is an advanced international level charger. Unique function High efficiency over the full load range, full load efficiency greater than 95% Wide output voltage range, 150-1000VDC, suitable for a wide range of Lithium or lead acid battery 5-inch LCD touch screen, easy to operate Flexible application, charging voltage, charging current, charging time, timing charging can be set by LCD screen, easy to operate Main featuresï¼? Powerful protection, overheating, short circuit, overload, overvoltage, undervoltage, etc. Wide input voltage range: 260~ 530Vac, adaptable to various power grid environments Three-phase AC input without neutral wire: Simplifies system design, eliminates the risk of excessive neutral current, and reduces system costs. Dual DSP design, achieve the full digital control, less components means high reliability Wide input voltage range, allows operation in most poor grid conditions Battery anti backflow: effectively protects the battery while ensuring reliable and safe operation of the system Input, output have protective circuit breaker switch Module adopts hot pluggable design, which is convenient for maintenance. RS485 interface (Optional)
Instrumentation circuits cable is used for computer based automatic control system, especially for computer distributed control system, transmission of production device process variable detection, control, interlocking, alarm lamp analog and digital signals, the product has excellent anti-interference performance, long-term working temperature -40~105.
PV Cable is suitable for connecting cables between PHOTOVOLTAIC cells and AC and DC inverters. The product is suitable for the maximum 1.8kV DC voltage or 0.6/1kV AC voltage system. The product uses low smoke halogen-free flame retardant material, the product has the characteristics of high-temperature resistance, ozone resistance, ultraviolet resistance, oil resistance, wear-resistance and so on.
