Graphite Sic Surface Coat

DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.

PVA primer is the prime foundation coat to seal the wall surface and it helps attaining adhesion to the subsequent coat

* PHOSCAST
Phoscast : Phosphate Bonded Castables

* PURPOSE
customers using FBC boilers (Particularly underbed feed FBC boilers) for the protection of inbed coils against erosion potential by applying highly abrasive resistant refractory on inbed coils above fuel feed system.

BACKGROUND

* Two of such actions are providing special alloy studs on inbed coils and applying highly abrasive resistant refractory on the outer bottom loops of inbed Coils which are above the fuel feed nozzles.

* GANESHAS has taken number of approaches to identify the key factors affecting erosion rates with an objective to enhance the life of inbed tubes as well as implementing the corrective action to reduce the erosion rates.
Phosphate coatings are often used to protect steel parts against rusting and other types of corrosion

* Erosion of inbed coils in fluid bed combustor is unavoidable phenomenon however the rate of metal wastage and thus the life of tubes depends on various factors like ash & fuel properties, design of Combustor / feeding system, flue gas velocities operating conditions etc. It has been also observed that maximum erosion prone inbed coils are those which come above fuel feed nozzles and an area of approximately 1 to 1.5 mts around fuel feed systems are badly affected.

APPLICATION
Phoscast-90 XR can be applied by ramming with wooden mallet having adequately large head @" dia x 5" length x 10â?? Jong handle). The desired lining or repair thickness is built up in several courses while ramming the mass to uniform thickness. Phoscast refractory should never be trawled to obtain smooth surface; ramming only should finish surface. Any excess mass is to be sliced off with trowel edge and then finished by ramming again for bed coil. Tube application of AFBC boiler, the material pasty mass should be finger pressed into the studs of the tube with maximum force. Finish should be given by pressing the hand palm against material applied, using surgical type thin rubber hand gloves.

Our Wood Coating is one of the best seller products. Based in Mumbai, Maharashtra we offer a huge variety of 15 natural stains that have been especially specially formulated with the superior quality solvent based fast drying stains that aid in accentuating the natural beauty of the wood grains. Wipe and fill the surface and further smooth sand the surface with a 180 grit paper. Next, apply stain with muslin cloths in addition to the grains. Further let the surface dry for about 30 minutes before the application of the finish coat. You can mix the stains with the NC/ melamine finishes approximately 20% by volume, if required. Never mix the stains woody or PU finishes. We are the leading exporter, supplier and manufacturer of Wood Coatings.

1. Specialty coating products applicable on all surfaces
2. 0 VOC environmentally Friendly products
3. Extremely high corrosion resistance
4. Single component system - no mixing, no thinner required.
5. No shelf life or Pot life issues
6. Available in all RAL Shades
7. Suitable for application over -40 Deg Cel upto 200 Deg Cel temp range

Given the growing graphite is widely applied in industry, lack of material there to shake chu chen, the division began

To develop the graphite surface treatment to solve this problem, do vgi or sic for the graphite surface treatment

Technology has further breakthroughs can be applied to semiconductors, optoelectronics other industries.

Vgi is mainly used in surface treatment temperature below 600 degrees environment.

Sic is mainly used in surface treatment temperature below 1300 degrees environments.

Our Wood Coating is one of the best seller products. Based in Mumbai, Maharashtra we offer a huge variety of 15 natural stains that have been especially specially formulated with the superior quality solvent based fast drying stains that aid in accentuating the natural beauty of the wood grains. Wipe and fill the surface and further smooth sand the surface with a 180 grit paper. Next, apply stain with muslin cloths in addition to the grains. Further let the surface dry for about 30 minutes before the application of the finish coat. You can mix the stains with the NC/ melamine finishes approximately 20% by volume, if required. Never mix the stains woody or PU finishes. We are the leading exporter, supplier and manufacturer of Wood Coatings.

AUTO PAINT (PEINTURE AUTOMOBILES)
AUTO PAINT PRIMER
1K PRIMER
2K PRIMER
NC SURFACER
NC PUTTY
POLYESTER PUTTY
2K THINNER
BASE COATS
2K PAINT
HARDENERS
PLASTIC PRIMER
FIBRE PUTTY
2K CLEAR VERNIS
METALLIC FINISH
PEARLSCENT
XIRALLIC

Special Structual Spray-coat material for running track surface installation ,consume 1.20-1.25KG/m2 to achive 3mm

Spray-coat Running track PU1:2 Spray-coat track material is an pigmented and solvent free thixotropic, two component polyurethane material with expanding form, strong resistance ,elastic properties, should be mix two component on project site,
Spray-coat Running tack PU1:2 Spray-coat track material is easy to apply ,it shows excellent resistance to moisture during the curing phase and a good curing behavior even at low temperature