5V 2A Power Charger Adaper

Supplier: Automotive lead acid battery

SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".

1. Main Features: 1. Input & output is fully insolated to endure impact of sensitive appliances and protect the inverter from being easily damaged. 2. High Surge: High surge current capability starts difficult loads such as TVs, camps, motors and other inductive loads. 3. Soft start: Smooth start-up of the appliances. 4. Pure sine wave output waveform: Clean power for sensitive loads. 5. Low total harmonic distortion: Below 5% 6. Stable working performance: Even in the situation of under voltage or over voltage, the inverter could endure 10% voltage fluctuation until it shutdowns. 7. Cooling fan with internal temperature sensor will turn on automatically when the inverters becomes warm and turn off after the temperature dropped. 8. LED indicator on the front panel shows the working and error state. 9. Digital displays indicate battery voltage and inverter output voltage. 2. Protect functions: 1. Over load protection 2. Over current protection 3. Over voltage protection 4. Low voltage protection 5. Surge protection 6. Short circuit protection 7. High temperature protection 8. Reverse connection protection 9. External fuse protection 10. Buzzer alarm function 3. Applicable for: ( Solar/Wind/Home System ) 1. Travel set equipment 2. Industrial equipment 3. Office equipment 4. Kitchen equipment 5. Household electrical equipment 6. Power tools 5. Technical Parameter:  Input: Input voltage: DC12V/DC24V/DC48V Working Voltage: DC10V-15V/DC20V-30V/DC40V-60V Input current: 166A/ 83A/41.67A Standby input power: 2200W Short circuit protection Digital display Indicator:  Inverter woking: green light on Inverter problem: no 110V/220v display Charging indicator: digital of voltage up slowly Charging process indicator: digital display charging voltage Turn off the switch when charging which charging battery faster Protection alarm:  Low input voltage alarm: buzzer Low input voltage protection: no display, buzzer and inverter stop working High input voltage protection: no output voltage display, have input display, inverter stop working. Over load protection: voltage drop to 55V-140V Abnormal temperature: no AC display, buzzer and stop working. Environment: High temperature protectioin: =70ºC Working Temperature: -10ºC~40ºC Cooling mode: Intelligent Temperature control Fan Package included: 1* QW-P2000UPS 1* battery clamp 1* spare part 1* english user manual 1* standard packing box 4. Warranty: 12 months    Quality stanstard: CE, RoHS

Battery charger for all type of industrial battery 1. Thyristor base 2. Smps base Rane from 5 amp 24vdc to 2000 apm Iec

CTEK battery charger for car, commercial vehicles off road vehicle and motorcycle. Jump starter, Foxwel OBD scanner.

Supplier: Batteries from 5 ah up to 200 ah, batteries chargers, solar panels

Supplier: Solar batteries, tubular batteries, lead acid batteries, solar power, motorcycle batteries, automotive batteries

Supplier: Lead acid batteries, tubular batteries, solar batteries, inverter batteries, industrial batteries, automotive batteries