Full Servo Under Pad &puppy Pad Production Line

* PHOSCAST Phoscast : Phosphate Bonded Castables * PURPOSE customers using FBC boilers (Particularly underbed feed FBC boilers) for the protection of inbed coils against erosion potential by applying highly abrasive resistant refractory on inbed coils above fuel feed system. BACKGROUND * Two of such actions are providing special alloy studs on inbed coils and applying highly abrasive resistant refractory on the outer bottom loops of inbed Coils which are above the fuel feed nozzles. * GANESHAS has taken number of approaches to identify the key factors affecting erosion rates with an objective to enhance the life of inbed tubes as well as implementing the corrective action to reduce the erosion rates. Phosphate coatings are often used to protect steel parts against rusting and other types of corrosion * Erosion of inbed coils in fluid bed combustor is unavoidable phenomenon however the rate of metal wastage and thus the life of tubes depends on various factors like ash & fuel properties, design of Combustor / feeding system, flue gas velocities operating conditions etc. It has been also observed that maximum erosion prone inbed coils are those which come above fuel feed nozzles and an area of approximately 1 to 1.5 mts around fuel feed systems are badly affected. APPLICATION Phoscast-90 XR can be applied by ramming with wooden mallet having adequately large head @" dia x 5" length x 10â?? Jong handle). The desired lining or repair thickness is built up in several courses while ramming the mass to uniform thickness. Phoscast refractory should never be trawled to obtain smooth surface; ramming only should finish surface. Any excess mass is to be sliced off with trowel edge and then finished by ramming again for bed coil. Tube application of AFBC boiler, the material pasty mass should be finger pressed into the studs of the tube with maximum force. Finish should be given by pressing the hand palm against material applied, using surgical type thin rubber hand gloves.

APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.

Quartz is the most abundant and most common mineral on the Earth. It is found in almost every geological environment and also it is at least a component of almost every rock type. It has a hexagonal crystal structure and is made of trigonal crystallized silica. It is most varied in terms of varieties, colours and forms. The most important distinction between the types of quartz is that one is of macro crystalline, which is individual crystal visible to the unaided eye, and the other is microcrystalline or cryptocrystalline varieties, aggregates of crystals visible only under high magnification. Chalcedony is the generic term for cryptocrystalline quartz. The transparent variety tends to be microcrystalline and the cryptocrystalline varieties are either translucent or mostly opaque.

GOOD GRADE OCC WASTE PAPER SCRAP MADE IN USA GRADE 11 AND 12 Place of Origin : JAPAN, US, EUROPE Materials : Waste Paper Type : OCC, ONP, OMG, YELLOW PAGES, A3, A4 WASTE PAPER Color : Mixed & NOT MIXED Unit : Ton/Tons Minimum Order : 20 Tons Payment Term : T/T 50/50 and L/C 100% at sight Shipping Lines : Ocean shipping Estimate Lead Time : 15 - 20 days Shipping Origin : Tokyo, Yokohama, Hamburg, New York, Long Beach Supplying Capacity : 200 tons/month Packaging : Bale (1.2-1.4 Tons/Bale), 20-25 Tons loading 40FT container

Our export-quality padlocks are designed for superior security and durability, meeting global standards. Made from high-grade materials like hardened steel and brass, they offer exceptional resistance to corrosion, tampering, and harsh weather conditions. The locks feature precision mechanisms for smooth operation and enhanced protection against picking and cutting. Available in various sizes and designs, our padlocks can be fully customized to meet specific security needs. We offer personalization options such as engraved logos, unique keying systems, and custom finishes, making them ideal for bulk orders in industries, commercial spaces, or for personalized branding, ensuring reliability and customer satisfaction worldwide.

Pad Lock

Pad Lock