Technical specifications
Exist status : brown liquid
Solid content : 40 1.0
Viscosity : 220 50 cps.
Specific gravity : 1.10 0.02
Ph : 6.0 1.0
Chloride content : below 0.001%
In a 200kg drum
In 1m3 ibc
In a flexi bag
This is chemical setting Furan based chemical resistant mortar which is combination of Liquid and Powder, when mixed in proper proportion from workable mortar which after setting and curing give of liquid and give black highly cross linked composites. Furan When set and cured is resistant to highly corrosive acids, alkalis and to powerful organic solvents such as ketones, Aromatic and Chlorinated solvents. It has extreme resistant to Acidic & alkalis, Salts, Greases and Detergents. It resists to Organic & Inorganic acids at their boiling temperature. It is suitable against mild chlorine Gas (dry) phosphorous trichloride, pyridine at room temperature. Furan is especially useful where resistance to mixed media such as aqueous acids /alkalis and organic solvents is needed in chemical plant process and waste streams. Carbon filled Furan is used against corrosive effect of hydrofluoric acid & its salts. PREPARATION OF FURANE MORTAR : Mortar consist of Furan solution and Furan powder. The average mixing ratio necessary to obtain mortar with good working consistency is 1 part by weight Solution & 3 part by weight powder. The ratio will vary slightly depending on temperature and working conditions.Stir the liquid thoroughly before using. Place liquid in a suitable shallow mixing pan. Add powder by weight in the solution mix thoroughly and rapidly until all lumps are dispersed and the mortar is completely homogenous. Spread out the mortar in a thin layer, not more than ¾ thick, to dissipate the heat of reaction and lengthen the working life. Batch size can be varied depending upon the temperature and the speed with which the masons are working. Very large batches will become stiff quite rapidly. Make sure that all the Furan Motrar is used from the pan before another batch is mixed.When working at temperature above 40 C, very small batches not more than 2 Kgs, should be prepared. When working at temperature below 15C the liquid should be kept warm.
Technical specifications Exist status : brown liquid Solid content : 40 1.0 Viscosity : 150 50 cps. Specific gravity : 1.10 ¡ó 0.02 Ph : 6.0 1.0 Chloride content : below 0.001% In a 200kg drum In 1m3 ibc In a flexi bag
Product : Long Radius Bend Brand : Renaissance Pipe Fitting Inc. Sizes : Refer the specification Condition : New Rating : 4.6, based on 23 reviews price : Start from 10 USD RFP India is a well-known exporter, manufacturer and supplier of Long Radius Bends Butt Weld Pipe Fittings worldwide in the steel market industry. The purpose of Radius Pipe Bends is to amend the direction and flow through 180 degree angle. Coming in two important forms of Bends short radius bend and long radius bend to which both of them are having a midpoint-to- midpoint length, along with double the indistinguishable 90 degree elbow. The most important application for these pipe fittings is in heater coils and heat exchangers. Long Radius Pipe Bends Butt Weld Pipe Fittings are manufactures with dissimilar grades of standard ranges and meets its provisions through international and national standards. They are quite unproblematic to remove and install, and can be accessible to our customers in diverse technical specifications of sizes and threading as per necessity. Standard : ANSI/ASME, MSS, JIS, DIN, BS etc TYPE : SEAMLESS / WELDED/ FABRICATED RANGE : 2"NB TO 18"NB IN SCH: 20, 40, STD, 60, 80, XS, 100, 120, 140, 160, XXS available with NACE MR 01-75 FORM : Long Radius Bend, Industrial Long Radius Bend, Piggable Bend, Induction Bend Radius( R ) : 3D, 5D, 6D, 8D, 10D & 20D. Stainless Steel Long Radius Bends : Standard : ASTM / ASME A/SA 403 GR WP "S" "W" " WX" Grade : 304, 304L, 304H, 309S, 309H, 310S, 310H, 316, 316TI, 316H, 316L, 316LN, 317, 317L, 321, 321H, 347, 347H, 904L Duplex Steel Long Radius Bends : Standard : ASTM / ASME SA 815 Grade : UNS NO.S 31803, S 32205 Aluminium Long Radius Bends : Standard : ASTM / ASME SB241 Grade : 3003 H18 , 3003 H112, 6061 T6, 6063 T6, 6351 T5, 6351 T6
Supplier: Construction chemicals, concrete admixture , polycarboxylic acid
Incoloy Alloy 908 is a high-temperature, high-strength, and highly corrosion-resistant alloy composed of elements such as nickel, chromium, molybdenum, and iron. It is a single-phase austenitic alloy, typically formed by casting and forging. Chemical composition: The chemical composition of Incoloy Alloy 908 is composed of elements such as nickel, chromium, iron, molybdenum, vanadium, manganese, tantalum, silicon, carbon, phosphorus, and sulfur. Nickel content is 40-45%, chromium content is 20-23%, iron content is 16-19%, and molybdenum content is 8-10%. Mechanical properties: Incoloy Alloy 908 has excellent high-temperature and high-strength performance. Its tensile strength is 135 ksi (930 MPa) (minimum), yield strength is 70 ksi (480 MPa) (minimum), and elongation is 25% (minimum). Physical properties: The density of Incoloy Alloy 908 is 8.14 g/cm�³, the melting point is 1338�°C (2440�°F), the thermal conductivity is 11.7 W/m�·K (100�°C), and the coefficient of thermal expansion is 13.7 �¼m/m-K (20-100�°C). Corrosion resistance: Incoloy Alloy 908 has excellent corrosion resistance, especially in high-temperature, high-pressure, and highly corrosive environments. It can withstand the corrosion of corrosive media such as sulfuric acid, hydrochloric acid, nitric acid, and fluoride, and can resist chloride stress corrosion cracking (SCC). The international standard designations for Incoloy alloy 908 include UNS N09908 and W.Nr. 1.4876. There are also corresponding standards and specifications in different countries and regions, such as AMS and ASTM standards in the United States, EN standards in Europe, and JIS and JPI standards in Japan. Here are the specific standards and designations for Incoloy alloy 908 in different countries: United States: AMS 5545, AMS 5546, AMS 5547, AMS 5549, ASTM B408, UNS N09908 Germany: DIN 17752, DIN 17753, DIN 17754, W.Nr. 1.4876 United Kingdom: BS HR 6 Europe: EN 10095 Japan: JIS H4551, JPI-SB46 We can provide the following the form:Incoloy alloy908 coil; Incoloy alloy908 strip;Incoloy alloy908 plate; Incoloy alloy908 sheets; Incoloy alloy908 tube; Incoloy alloy908 pipe;Incoloy alloy908 flat; Incoloy alloy908 bar GB:HR 6/JIS:H4551/UNS:N09908/W.Nr:1.4876
Supplier: Fertilizers and intermediate chemicals, sulphur (granules, lumps, pastilles, powder), mop (potash, kcl salt), sop ( potassium sulphate), urea n46% dap, ammonia, ammonium nitrate, nitric acid, rock phosphate, soda ash, npk, sulfuric acid, phosphoric acid, cement and raw materials, cement grades 32.5, 42.5, 52.5 n/r, clinker, coal, pet coke
Services: Trade
Buyer: Fertilizers and intermediate chemicals, sulphur (granules, lumps, pastilles, powder), mop (potash, kcl salt), sop ( potassium sulphate), urea n46% dap, ammonia, ammonium nitrate, nitric acid, rock phosphate, soda ash, npks, sulfuric acid, phosphoric acid, cement and raw materials, cement grades 32.5, 42.5, 52.5 n/r, clinker, coal, pet coke
Description Polycarboxylate Superplasticizer concrete admixture (Powder) is a high performance, 100% poly-carboxylate based polymer, also named PCE. Polycarboxylate Superplasticizer concrete admixture (Powder) is specifically developed as an effective dispersant, fluidifier and high range water reducing agent for concrete and other mineral materials, which is air entraining. It complies with ASTM C 494, Type F specifications. Application As a new generation of environmental friendly concrete admixtures, Polycarboxylate Superplasticizer concrete admixture (Powder) can be applied in hydraulic, electricity, port, bridge, railway, tunnels and highway projects. In the production of self-compact precast concrete and conventional concrete, Polycarboxylate Superplasticizer concrete admixture (Powder) leads to low water/cement ratios, but maintains a normal level of workability. Features and Benefits Polycarboxylate Superplasticizer concrete admixture (Powder) has the same technical specifications with PC-L while remarkably reducing the cost of package and transportation. 2. Polycarboxylate Superplasticizer concrete admixture (Powder) is much easier to be handled in storage and transportation compared with PC-L. 3. Excellent compatibility with various types of cements. 4. High Water Reducing Rate: Low dosage, and low slump loss. Low chloride and alkali content, no corrosion to steel-bar. 6. High Stability: Neither precipitation nor layers at low temperature. 7. Environmental Friendly: Free from formaldehyde and nontoxic. Uses and Dosages 1. When Polycarboxylate Superplasticizer concrete admixture (Powder) is applied in the form of powder, normal dosage ranges from 0.15% to 0.6% of the weight of cementitious material in 1m3 of concrete. When applied in the form of liquid by being mixed with and dissolved into water, Polycarboxylate Superplasticizer concrete admixture (Powder) can be changed into liquid of which density varies from 10% to 40%. In order to optimize the dosage, experiments are required before the adoption of it or changing of the cement type. 2. Recommended dosage: 0.2% of the weight of cementitious material in 1m3 of concrete. 3. Polycarboxylate Superplasticizer concrete admixture (Powder) can be added into cement paste together with water or after mixing, while the latter approach is preferred. 4. The quantity of water must be strictly controlled when Polycarboxylate Superplasticizer concrete admixture (Powder) is applied, since slump loss of concrete is closely related to it. 5. Polycarboxylate Superplasticizer concrete admixture (Powder) is alkalescent, nontoxic, non-corrosive and environmental friendly. If it gets onto skin or in the eyes, please wash it off with clean water at once. If there is skin allergy, please see a doctor. 6. Do not mix it with naphthalene-based admixtures. If other admixtures, such as set retarder or corrosion-inhibiting admixture, are required simultaneously for some special projects, compatibility tests should be conducted beforehand. 7. When applying Polycarboxylate Superplasticizer concrete admixture (Powder) in steam curing concrete or other special concrete, abundant experiments are highly recommended to make sure it satisfies the expected requirement. 8. When Polycarboxylate Superplasticizer concrete admixture (Powder) is used to make concrete at or below C45, the total cost may be reduced by increasing the quantity of minerals. Package, Storage & Handling 1. Polycarboxylate Superplasticizer concrete admixture (Powder) for powder: Woven fabric bag with plastic liner. Net weight: 20kg +/- 0.13 kg. 2. Polycarboxylate Superplasticizer concrete admixture (Powder) needs to be stored in well-ventilated and dry place. 3. Keep Polycarboxylate Superplasticizer concrete admixture (Powder) from sunlight and below freezing point. Its storage stability can retain 12months in original package, but please use it up in 60days if it's been opened and repacked. 20kg/bag, 12 tons loaded in a 20ft.
Description Polycarboxylate Superplasticizer concrete admixture (40%) is a high performance, 100% poly-carboxylate based polymer, also named PCE. Polycarboxylate Superplasticizer concrete admixture (40%) is specifically developed as an effective dispersant, fluidifier and high range water reducing agent for concrete and other mineral materials, which is air entraining. It complies with ASTM C 494, Type F specifications. Application (1)As a new generation of environmental friendly concrete admixtures, Polycarboxylate Superplasticizer concrete admixture (40%) can be applied in hydraulic, electricity, port, bridge, railway, tunnels and highway. (2) In the production of self-compact precast concrete and conventional concrete, Polycarboxylate Superplasticizer concrete admixture (40%) leads to low water/cement ratios, but maintains a normal level of workability. Features and Benefits 1. Excellent compatibility with various types of cements. 2. High Water Reducing Rate: Low dosage, and low slump loss. 3Low chloride and alkali content, no corrosion to steel-bar. 4. High Stability: Neither precipitation nor layers at low temperature. 5. Environmental Friendly: Free from formaldehyde and nontoxic. Uses and Dosages 1.When Polycarboxylate Superplasticizer concrete admixture (40%) is applied, the dosage normally ranges from 0.3% to 1.2% of the weight of cementitious material in 1m3 of concrete. In order to optimize the dosage, experiments are required before the adoption of it or changing of the cement type. 2.Recommended dosage: 0.4% of the weight of cementitious material in 1m3 of concrete.When applied in ready-mixed station, it should be diluted into solution with the concentration of 10% and the recommended dosage. 3.Polycarboxylate Superplasticizer concrete admixture (40%) can be added into cement paste together with water or after mixing, while the latter approach is preferred. 4.Polycarboxylate Superplasticizer concrete admixture (40%) is alkalescent, nontoxic, non-corrosive and environmental friendly. If it gets onto skin or in the eyes, please wash it off with clean water at once. If there is skin allergy, please see a doctor. 5.Do not mix it with naphthalene-based admixtures. If other admixtures, such as set retarder or corrosion-inhibiting admixture, are required simultaneously for some special projects, compatibility tests should be conducted beforehand. 6.The quantity of water must be strictly controlled when Polycarboxylate Superplasticizer concrete admixture (40%) is applied, since slump loss of concrete is closely related to it. 7.When applying Polycarboxylate Superplasticizer concrete admixture (40%) in steam curing concrete or other special concrete, abundant experiments are highly recommended to make sure it satisfies the expected requirement. 8.When Polycarboxylate Superplasticizer concrete admixture (40%) is used to make concrete at or below C45, the total cost may be reduced by increasing the quantity of minerals. Package, Storage & Handling 1.Polycarboxylate Superplasticizer concrete admixture (40%) for liquid: It is packed in 1100kg (1000Liter) per IBC Tank. 2. Store it in covered containers and keep it from rain, sundry, and evaporation. 3. Keep Polycarboxylate Superplasticizer concrete admixture (40%) from sunlight and below freezing point. Its storage stability can retain 12months in original package, but please use it up in 60days if it been opened and repacked. 1.16 tons/IBC tank, 20.88 tons loaded in a 20ft.
PCE superplasticizer is the newest generation superplasticizer used for concrete in domestic and abroad.It is based on molecular designs and adsorption capacity of polycarboxylate,we do R&D and successfully produce water reducing and retention type polycarboxylate superplasticizer for concrete.With initiating systerm and reaction conditions,we achieve high adaptability.Comparing with PNS and other superplasticizer, PCE superplasticizer has many characteristic advantages in technology and performance as following: (1) low dosage, high rate of water reducing; (2) keep concrete good slumption retention; (3) good compatibility with cement; (4) small shrinkage of concrete to keep the stability of volume and durability; (5) environmental in production and usage. Base on above advantages.