Polyethylene 3Ply Tape

I description: Polyethylene anticorrosive tape is cold applied tape coating system for corrosion protection of oil, gas, petrochemical, and waste water underground or overhead pipelines. The inner-layer tape shall be applied after the primer and before the outer-layer tape by hand or with a wrapping machine structure The specification of the tape consists of two layers, adhesive layer and film backing Adhesive: butyl rubber Outer layer: special blend of stabilized polyethylene Iii Features Excellent adhesion to pipe and self Resistant to uv Can be applied over a wide temperature range Good conformability and consistent uniform thickness Easily applied with no special equipment Compatible with common pipe coatings Excellent resistance to cathodic disbonding Meets astm d 1000 standard Cold applied Technical datas: Inner wrap tape: xunda-t 100 series TypeT-150T-165T-180 Total thickness0.51 mm0.65 mm0.80 mm Polyethylene film0.31 mm0.34 mm0.39 mm Synthetic adhesive0.20 mm0.31 mm0.41 mm Elongation at break„d 400% Tensile strength60 n/cm61.2 n/cm63 n/cm Yield strength35.5 n/cm42.3 n/cm45.5 n/cm Peel adhesion to primed pipe21.2 n/cm26.5 n/cm33.2 n/cm Dielectric strength35 kv/mm45.8 kv/mm48 kv/mm Cathodic disbandment0.24 in radius 6.4 mm Volume resistivity2.5 x 1012 ohm.M Water vapor transmission rate „t 0.1gm/m2/24h Water absorption rate < 0.06% Recommended application temperature -5 to +600 c Max serve temperature-40 to + 800 c ColorBlack Available roll size (width x length)2" to 9" x 50 to800 feet. Paper cartons packing with waterproof membrane.

Polyethylene anticorrosion tape is cold applied tape coating system for corrosion protection of oil, gas, petrochemical, and waste water underground or overhead pipelines. The outer-layer tape backing shall be compounded so that it will be resistance to outdoor weathering. The outer-layer tape shall be applied after the inner-layer tape by hand or with a wrapping machine. Ii structure The specification of the tape consists of two layers, adhesive layer and film backing Adhesive: butyl rubber Outer layer: special blend of stabilized polyethylene Iii features: Excellent adhesion to inner-layer tape and self Resistant to UV Can be applied over a wide temperature range Good conformability and consistent uniform thickness Easily applied with no special equipment Compatible with common pipe coatings Excellent resistance to cathodic disbonding Meets astm d 1000 standard Cold applied technical datas: Outer wrap tape: xunda-t200 series TypeT 250T 265T 280 Total thickness0.51 mm0.65 mm0.80 mm Film0.38 mm0.51 mm0.63 mm Adhesive0.13 mm0.14 mm0.17 mm Elongation at break„d 400% Tensile strength45.3 n/cm50.8 n/cm60.1 n/cm Yield strength35.9 n/cm43.4 n/cm45.8 n/cm Dielectric breakdown32.9 kv/mm43.5 kv/mm45.2 kv/mm Cathodic disbandment0.24 in radius 6.4 mm Volume resistivity2.5 x 1012 ohm.M Water vapor transmission rate „t 0.08 gm/m2/24h Water absorption rate < 0.07% Recommended application temperature -50 to +600 c ColorWhite Available roll size (width x length)2" to 9" x 50 to 800 feet. Paper carton packing with waterproof membrane.

Polyethylene joint tape is cold applied tape coating system for anti corrosion of field joints, fittings, and specifically pipeing. The adhesive is a key in ground performance characteristic coupled with the low and high density polyethylene backing. The joint wrap tape shall be applied by hand or with a wrapping machine. II structure The specification of the tape consists of two layers, adhesive layer and film backing Adhesive: butyl rubber Outer layer: special blend of stabilized polyethylene III features: Heavy duty adhesive Resistant to UV Can be applied over a wide temperature range Good conformability and consistent uniform thickness Easily applied with no special equipment Conformable to irregular shapes. Meets astm d 1000 standard Cold applied Technical datas: ItemT-365T-380T-3100T-3130 Total thickness (mm)0.640.761.021.27 Backing thickness (mm)0.280.300.350.50 Adhesive thickness (mm)0.360.460.670.77 Tensile strength (n/ cm)456080100 Elongation (%)400 450450500 Adhesion to prime pipe (n/cm)25 Dielectric strength (kv/cm)404242.545 Volume resistivity.M)2.5x10122.5x10122.5x10122.5x1012 Water vapor transmission rate24h0.1 Water absorptivity (%)0.10.1 Uv resistance 600h80 %80 %80 %80 % Application temperature -5 to 60 0 c Max serve temperature-40 to 80. Paper carton packaging with waterproof membrane.

Polyethylene Pipelines Cold Applied Tape Composition: It is tape-shaped anticorrosion material made of Polyethylene film heat laminated with adhesive layer of butyl glue. Usage: It is extensively used in the pipework of oil and natural gas transportation, petrochemical industry, electric power, metallurgy, urban natural gas network of pipes, the outside anticorrosion project of the metal pipes involved as well as the outside anticorrosion project of the underground and overhead metallic conduit of the works of petrochemical industry, natural gas and coal transportation Thickness: 0.30 - 1.30mm Width: 50, 75, 100, 150, 230, 300mm Length: 30 - 200m Features: Excellent adhesion to pipe and self Resistant to UV Can be applied over a wide temperature range Good conformability and consistent uniform thickness Easily applied with no special equipment Compatible with common pipe coatings Excellent resistance to cathodic disbonding Meets ASTM D 1000 Standard Cold applied Application: Prepare surfaces by removing all loose scale, rust or other foreign matter by grit blasting or wire brush. Surface must be clean, dry and free of grease. Apply thin film of Butyl Primer to all surfaces to be wrapped and allow to dry. Peel back interleaving and apply adhesive side of the tape to the surface and press down. Apply the tape spirally with enough tension to make it conform. Remove interleaving as wrapping proceeds. Overlap each turn by at least 1" or 55% to achieve double thickness. Irregular surfaces such as valves, flanges, etc. packing in carton

Supplier: Stretch Film, Polypropylene Strap, And Polyethylene Strap.

Inner tape Name: inner wrap tape for cold applied tape coating Type: t-140, t-150, t-165, t180, t1100, t1130 Price: fob ningbo or shanghai Place of production: china Brand: ideal Term: l/c, t/t Volume: 8, 000, 000sqm/yr Packing: carton Features: The specification of the tape consists of two layers, adhesive and film Inner layer: butyl rubber Outer layer: polyethylene Thickness: 0.40 - 1.30mm Width: 50, 75, 100, 150, 230, 300mm Length: 30 - 200m Tapes specifications: T-140 with 0.38mm / 15mil thickness and 50 - 230mm width T-150 with 0.51mm / 20mil thickness and 50 - 230mm width T-165 with 0.64mm / 25mil thickness and 50 - 230mm width T-180 with 0.76mm / 30mil thickness and 50 - 230mm width T-1100 with 1.02mm / 40mil thickness and 50 - 230mm width T-1130 with 1.27mm / 50mil thickness and 50 - 230mm width 38kg/box

Jining XunDa Anticorrosion tape for pipeline 100 Series is polyethylene cold applied tape coating system for corrosion protection of Oil, Gas, Petrochemical, and Waste Water underground or overhead pipelines. Usage and Features:1. Widely used on underground and overhead pipelines anticorrosion protection system. 2. Excellent adhesion to pipe and self 3. Resistant to UV 4. Can be applied over a wide temperature range from-30¡ãC to 80¡ãC 5. Good conformability and consistent uniform thickness 6. Cold applied ,and easily applied with no special equipment 7. Compatible with common pipe coatings 8. Excellent resistance to cathodic disbonding 9. Meets ASTM D 1000 Standard 10. Long term corrosion protection and mechanical resistance The tape consists of two layers, adhensive and filmInner layer: butyl rubberOuter layer: polyethyleneThickness: 0.35 - 1.30mmWidth: 50-300mmLength: 30 - 200mTapes specifications: 1) T-150 with 0.51mm / 20mil thickness and 50 - 300mm width2) T-165 with 0.65mm / 25mil thickness and 50 - 300mm width3) T-180 with 0.80mm / 30mil thickness and 50 - 300mm width packing in carton

Pipeline Wrap tape The tape as consists of two parts: 1. Adhesive: Inner layer of Butyl rubber. 2. Backing: Outer layer of Polyethylene(PE) Plastic. Specification of tape: Inner wrap tape: T-140 (0.38mm), T-150 (0.51mm), T-165 (0.64mm), T-180 (0.76mm), T-1100 (1.02mm), T-1130 (1.27mm); Outer wrap tape: T-240 (0.38mm), T-250 (0.51mm), T-265 (0.64mm), T-280 (0.76mm), T-2100 (1.02mm), T-2130 (1.27mm); Joint wrap tape: T-365 (0.64mm), T-380 (0.76mm), T-3100 (1.02mm), T-3130 (1.27mm); Thickness:0.38mm-1.3mm, Width:50mm, 75mm, 100mm, 150mm, 230mm, 300mm Lengh: 30-300m Synthetic Primer: P19: Solid content 19%; P27: Solid content 27%. Mastic filler:: N99: Solid content 99 packing in carton

Pipe Wrap, Joint Coatings & Accessory Products Xunda carries a full line of products to complement the main line coating systems and meet the challenges of modern pipeline activities. Utility work: hand-applied tape products for gas utility, oil field, and plumbing applications on small diameter pipe. Coating repair: cold-applied tape products for plant and field repair of main line coating systems. Specialty fittings and fabrication work: a variety of tape systems and mastics that conform to irregularly-shaped pipe. Field joints: single-sided and double-sided tape systems that conform to bell and spigot, welded and mechanically-coupled field joints. ROW construction: Rockshield system, tie-in, and above-ground tape systems for use at the job site by the pipeline contractor. Offshore Tapes: Whether replacing PVC on welded joints or protecting Pier Pilings, Xunda has the tape coating for the job. packing in carton