Crusher Backing Compound

APPLICATION OF SK-HB K-SILICATE MORTAR :

* K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors.
It is also used for jointing chemical resisting stoneware pipes.
K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles.
The concrete surface needed protection should be dryed, clean and rough.
The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner.

When Bedding and Jointing Materials are the same.
On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints.
The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water.
Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic.
When Bedding and Jointing Materials are Different.
Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR
A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions.

PREPARATIONS OF MORTAR :
* Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan.

* Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar.

* In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared.

* The cement mortar will be used before it starts setting.

Company Profile:-
the trusted name and one-stop destination and pioneer engineering company for crusher spare parts. We are providing a wide range of premium quality stone crusher spare/wear parts.
Industries ensures higher productivity, better reliability, long-lasting spare part life, and outstanding final product quality. Our competitively priced crusher spare parts keep your crusher working at peak-level performance.
Our high-performing range of Hi Manganese steel casting, Hi Manganese Jaw Plates, Hi Manganese Concave Mantle liners, Cheek Plates, Side liners and bronze frame bushing, Bronze Eccentric bushing, Bronze thrust bearings, socket liner, steel spare parts like spider bush, protection bush, Top bearing, Main shaft sleeve, Spider Cap, Arm Liners, Top Liners, Eccentric main shaft, Top shell, Bottom shell. Gasket, Hydraulic seal, Dust seal ring, Lube filters, Hydraulic filters, OPDS filters, Jaw crusher wedges, support bars, wedge bolts, Hammer screws, dumper pads, and grease seal.
Our characteristics and Advantages
We are confident that our spare and replacement parts will get better results because our team of engineers has found ways to improve the design of components where they can. We focus on the typical causes of failure for each part to develop replacements that will hold up longer and function better.
Throughout our development and testing process, we keep in mind that the quality parts must fit in your crusher without any modifications. During your next scheduled part replacement, your maintenance operators can install our components without any additional steps or training. Experience the difference that it makes to have parts that outlast and outperform the original design.
Crusher spare parts are designed to not only get your equipment back up and running but to also improve your business. These highly durable parts last longer, cut down on maintenance time and improve throughput. And because they re backed by exceptional customer service, you ll always have the right resources to ensure the best parts solutions for your crushers.

Series Jaw Crushers are the most preferred types of crushers due to their strong design, ability to crush materials of any hardness, low operating costs and easy maintenance. Depending on the location of the facility, they can be manufactured as mobile, fixed steel legs, fixed concrete legs, and fixed skid chassis.
Crushing of Jaw crushers is provided by applying a high amount of pressure to the material fed. This mechanical pressure is provided by the elliptical movement of the movable jaw and the narrowing angle between the fixed jaw. The fed material is gripped by this elliptical movement and compressed between the fixed jaw and the movable jaw. The high flywheel speed, the optimal jaw gripping angle and the specially designed geometry between the pitman and the back block ensure that this mechanical pressure is applied to the maximum level in a controlled manner. Therefore, Series Jaw Crushers have the strongest breaking circle that offers superior success in all working conditions.

Our Jaw Crushers can crush 50 tons to 800 tons of stones depending on the inlet openings. We can offer the most suitable breaker model according to customer needs and requests.

Features:
It has a long-lasting body against wear.
There is no daily maintenance other than lubrication.
It enables processing of raw material in larger sizes compared to impact crushers.
With the hydraulic system, the adjustment time is reduced to a minimum.
It consumes little energy. It works with high capacity at low kW value.

Technicial Specifications:
Type: Primary Jaw Crusher
Inlet Mouth: 900x650 mm
Outlet Mouth: 50x150 mm
Capacity: 50-150 t/h
Power: 75 kW
Weight: 12100 kg
Dimension: 1680-900-2200

Please CALL us for our other Crushing plants and customer-specific solutions