Tobee Wear Parts Impeller SPR10206 of 100mm SPR Vertical Sump Pumps are made of Ethylene Propylene Diene Monomer (EPDM) material which replace original 100RV-SPR Vertical Pump Parts on site.
Tobee Vertical slurry pump named vertical spindle pump, Vertical sump pump, vertical cantilever pump. vertical submerged pump. Vertical sewage pump, Column pump as well.
Impeller SP10206 - Double suction impellers (top and bottom entry) induce low axial bearing loads and have heavy deep vanes for maximum wear resistance and for handling large solids. Wear resistant alloys, polyurethane and moulded elastomer impellers are interchangeable. The impeller is adjusted axially within the casting during assembly by external shims under the bearing housing feet. No further adjustment is necessary.
Casing SP10092 - Has a simple bolt-on attachment to the base of the column. It is manufactured from a wear resistant alloy for the SP and from moulded elastomer for the SPR.
Back Liner SP10041 - It forms a pump chamber with throat bush and volute liner where the slurry would flow through them, Tobee offers back liners are interchangeable with stardard pump back liners with high chrome, natural rubber, polyurethane for different working condition.
pump impellers are interchangeable with AH/HH/LM pump impellers, The Impeller is one of the most important parts for slurry pump. Centrifugal slurry pumps need impeller to produce the centrifugal force which transfer the . The centrifugal force is produced by the impeller which rotates to a certain speed, As main rotating component which normally has vanes to impart the centrifugal force to the liquid, Usually, slurry pump impellers have a plain or a Francis type vane.
Impeller for 8AHF Pump
OEM Andritz ACP series pump spares Impeller ACP 150-400.5 semi-open type in a highly wear-resistant design.
Vertical slurry pump named vertical spindle pump, Vertical sump pump, vertical cantilever pump. vertical submerged pump. Vertical sewage pump, Column pump as well. Impeller SP10206 - Double suction impellers (top and bottom entry) induce low axial bearing loads and have heavy deep vanes for maximum wear resistance and for handling large solids. Wear resistant alloys, polyurethane and moulded elastomer impellers are interchangeable. The impeller is adjusted axially within the casting during assembly by external shims under the bearing housing feet. No further adjustment is necessary. Casing SP10092 - Has a simple bolt-on attachment to the base of the column. It is manufactured from a wear resistant alloy for the SP and from moulded elastomer for the SPR. Back Liner SP10041 - It forms a pump chamber with throat bush and volute liner where the slurry would flow through them, Tobee offers back liners are interchangeable with stardard pump back liners with high chrome, natural rubber, polyurethane for different working condition. Vertical Sump Pump Parts: Bearing Assembly - The bearings, shaft and housing are generously proportioned to avoid problems associated with the operation of cantilevered shafts in the first critical speed zones. The assembly is grease lubricated and sealed by labyrinths; the upper is grease purged and the lower protected by a special flinger. The upper or drive end bearing is a parallel roller type whilst the lower bearing is a double taper roller with preset end float. This high performance bearing arrangement and robust shaft eliminates the need for a lower submerged bearing. Column Assembly - Completely fabricated from mild steel. The SPR model is elastomer covered. Discharge Pipe - Metal for SP, elastomer covered for SPR. All wetted metal parts are completely rust protected. Submerged Bearings - None Agitation - An external agitator spray connection arrangement can be fitted to the pump as an option. Alternatively, a mechanical agitator is fitted to an extended shaft protruding from the impeller eye. Materials - Pumps can be manufactured in abrasive and corrosive resistant materials.
Interchangeable Pump Parts Impeller ACP 80-250 3+3 SO of EN.1.4474 are widely used for highest efficiencies in various industrial applications.
Discharge diameters - 40mm to 250mm Flow rate to 1267m3/h Head range to 40m As customers'requests
Type ZJ and ZJLR pumps are vertical, centrifugal slurry pumps submerged in sumps to work. They are designed for delivering abrasive, large particle and high slurries. These pumps have no need of any shaft seal and sealing water. they can also be operated normally for insufficient suction duties. Wet parts of Type ZJL pump are made of abrasion-resistant metal. All parts of type ZJLR pump immersed in liquid are lined with rubber our liners. They are suited to transport non-edge angle abrasive slurry.
The Sump Pump incorporates outstanding features of previous designs com¡ bined with improvements resulting from years of experience in the manu¡facture and servicing of this type of unit. The rugged construction includes extra heavy shaft and fully supported alloy bronze bearing resulting in long life and trouble free operation. Replacement parts are readily available from stock and field servicing is easily undertaken. Compactness of design makes this unit ideally suited for drainage of basements, tunnels, boiler rooms, etc ....
Chicago Pneumatic's CP 0010 and CP 0020 sump pumps are designed for high performance and durability - which makes them ideal for removing water from trenches, ditches, manholes, industrial sumps and excavations. Both models will pump down to within only 7/8" from base. Features - Single-stage centrifugal units driven by powerful vane motors. - Double seals protect bearings and motor from water and mud. - Integral oiler provides continuous lubrication. - Integral strainer, air inlet valve. - Bronze impeller, cast-iron housing.
