* K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors.
It is also used for jointing chemical resisting stoneware pipes.
K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles.
The concrete surface needed protection should be dryed, clean and rough.
The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner.
When Bedding and Jointing Materials are the same.
On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints.
The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water.
Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic.
When Bedding and Jointing Materials are Different.
Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR
A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions.
PREPARATIONS OF MORTAR :
* Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan.
* Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar.
* In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared.
* The cement mortar will be used before it starts setting.
Buttweld fittings are available in various grades, primarily categorized by material type (carbon steel, stainless steel, alloy steel, etc.) and specific material standards (like ASTM A234 for carbon steel or ASTM A403 for stainless steel). Within these categories, different grades (e.g., WPB, WP304/304L, WP316/316L) are specified, each with its own chemical composition and mechanical properties.
Here's a breakdown of common buttweld fitting grades:
1. Carbon Steel:
ASTM A234 WPB: This is the most common grade for carbon steel buttweld fittings, known for its weldability and suitability for general-purpose applications.
ASTM A234 WPC: Another carbon steel grade, often used in higher-pressure applications.
MSS-SP-75 WPHY: High-yield carbon steel grades (e.g., WPHY 42, 46, 52, 56, 60, 65, 70) used in high-pressure pipelines.
ASTM A420 WPL3/WPL6: Low-temperature carbon steel grades.
2. Stainless Steel:
ASTM A403 WP304/304L/304H: Austenitic stainless steel grades, with 304L being a low-carbon version for enhanced weldability.
ASTM A403 WP316/316L/316H: Austenitic stainless steel grades, with 316L being a low-carbon version, and 316Ti offering enhanced high-temperature strength.
Other Grades: 317/317L, 321, 310, 347, 904L, 2205 Duplex.
3. Alloy Steel:
ASTM A234 WP1/WP5/WP9/WP11/WP22/WP91: These grades are used in high-temperature and high-pressure applications.
4. Other Materials:
Nickel Alloys: Monel, Nickel, Inconel.
Copper Nickel: CuNi10Fe1Mn, CuNi30Mn1Fe.
Aluminum, Titanium, etc.: Various other materials are also used for specific applications.
ASME B16.9 is a common standard for buttweld fittings, specifying dimensions and tolerances.
Buttweld fittings are available in various grades, primarily categorized by material type (carbon steel, stainless steel, alloy steel, etc.) and specific material standards (like ASTM A234 for carbon steel or ASTM A403 for stainless steel). Within these categories, different grades (e.g., WPB, WP304/304L, WP316/316L) are specified, each with its own chemical composition and mechanical properties.
Here's a breakdown of common buttweld fitting grades:
1. Carbon Steel:
ASTM A234 WPB: This is the most common grade for carbon steel buttweld fittings, known for its weldability and suitability for general-purpose applications.
ASTM A234 WPC: Another carbon steel grade, often used in higher-pressure applications.
MSS-SP-75 WPHY: High-yield carbon steel grades (e.g., WPHY 42, 46, 52, 56, 60, 65, 70) used in high-pressure pipelines.
ASTM A420 WPL3/WPL6: Low-temperature carbon steel grades.
2. Stainless Steel:
ASTM A403 WP304/304L/304H: Austenitic stainless steel grades, with 304L being a low-carbon version for enhanced weldability.
ASTM A403 WP316/316L/316H: Austenitic stainless steel grades, with 316L being a low-carbon version, and 316Ti offering enhanced high-temperature strength.
Other Grades: 317/317L, 321, 310, 347, 904L, 2205 Duplex.
3. Alloy Steel:
ASTM A234 WP1/WP5/WP9/WP11/WP22/WP91: These grades are used in high-temperature and high-pressure applications.
4. Other Materials:
Nickel Alloys: Monel, Nickel, Inconel.
Copper Nickel: CuNi10Fe1Mn, CuNi30Mn1Fe.
Aluminum, Titanium, etc.: Various other materials are also used for specific applications.
ASME B16.9 is a common standard for buttweld fittings, specifying dimensions and tolerances.
Buttweld fittings are available in various grades, primarily categorized by material type (carbon steel, stainless steel, alloy steel, etc.) and specific material standards (like ASTM A234 for carbon steel or ASTM A403 for stainless steel). Within these categories, different grades (e.g., WPB, WP304/304L, WP316/316L) are specified, each with its own chemical composition and mechanical properties.
Here's a breakdown of common buttweld fitting grades:
1. Carbon Steel:
ASTM A234 WPB: This is the most common grade for carbon steel buttweld fittings, known for its weldability and suitability for general-purpose applications.
ASTM A234 WPC: Another carbon steel grade, often used in higher-pressure applications.
MSS-SP-75 WPHY: High-yield carbon steel grades (e.g., WPHY 42, 46, 52, 56, 60, 65, 70) used in high-pressure pipelines.
ASTM A420 WPL3/WPL6: Low-temperature carbon steel grades.
2. Stainless Steel:
ASTM A403 WP304/304L/304H: Austenitic stainless steel grades, with 304L being a low-carbon version for enhanced weldability.
ASTM A403 WP316/316L/316H: Austenitic stainless steel grades, with 316L being a low-carbon version, and 316Ti offering enhanced high-temperature strength.
Other Grades: 317/317L, 321, 310, 347, 904L, 2205 Duplex.
3. Alloy Steel:
ASTM A234 WP1/WP5/WP9/WP11/WP22/WP91: These grades are used in high-temperature and high-pressure applications.
4. Other Materials:
Nickel Alloys: Monel, Nickel, Inconel.
Copper Nickel: CuNi10Fe1Mn, CuNi30Mn1Fe.
Aluminum, Titanium, etc.: Various other materials are also used for specific applications.
ASME B16.9 is a common standard for buttweld fittings, specifying dimensions and tolerances.
Buttweld fittings are available in various grades, primarily categorized by material type (carbon steel, stainless steel, alloy steel, etc.) and specific material standards (like ASTM A234 for carbon steel or ASTM A403 for stainless steel). Within these categories, different grades (e.g., WPB, WP304/304L, WP316/316L) are specified, each with its own chemical composition and mechanical properties.
Here's a breakdown of common buttweld fitting grades:
1. Carbon Steel:
ASTM A234 WPB: This is the most common grade for carbon steel buttweld fittings, known for its weldability and suitability for general-purpose applications.
ASTM A234 WPC: Another carbon steel grade, often used in higher-pressure applications.
MSS-SP-75 WPHY: High-yield carbon steel grades (e.g., WPHY 42, 46, 52, 56, 60, 65, 70) used in high-pressure pipelines.
ASTM A420 WPL3/WPL6: Low-temperature carbon steel grades.
2. Stainless Steel:
ASTM A403 WP304/304L/304H: Austenitic stainless steel grades, with 304L being a low-carbon version for enhanced weldability.
ASTM A403 WP316/316L/316H: Austenitic stainless steel grades, with 316L being a low-carbon version, and 316Ti offering enhanced high-temperature strength.
Other Grades: 317/317L, 321, 310, 347, 904L, 2205 Duplex.
3. Alloy Steel:
ASTM A234 WP1/WP5/WP9/WP11/WP22/WP91: These grades are used in high-temperature and high-pressure applications.
4. Other Materials:
Nickel Alloys: Monel, Nickel, Inconel.
Copper Nickel: CuNi10Fe1Mn, CuNi30Mn1Fe.
Aluminum, Titanium, etc.: Various other materials are also used for specific applications.
ASME B16.9 is a common standard for buttweld fittings, specifying dimensions and tolerances.
CS Wrought Fitting Buttweld Cross Tee
Buttweld fittings are available in various grades, primarily categorized by material type (carbon steel, stainless steel, alloy steel, etc.) and specific material standards (like ASTM A234 for carbon steel or ASTM A403 for stainless steel). Within these categories, different grades (e.g., WPB, WP304/304L, WP316/316L) are specified, each with its own chemical composition and mechanical properties.
Here's a breakdown of common buttweld fitting grades:
1. Carbon Steel:
ASTM A234 WPB: This is the most common grade for carbon steel buttweld fittings, known for its weldability and suitability for general-purpose applications.
ASTM A234 WPC: Another carbon steel grade, often used in higher-pressure applications.
MSS-SP-75 WPHY: High-yield carbon steel grades (e.g., WPHY 42, 46, 52, 56, 60, 65, 70) used in high-pressure pipelines.
ASTM A420 WPL3/WPL6: Low-temperature carbon steel grades.
2. Stainless Steel:
ASTM A403 WP304/304L/304H: Austenitic stainless steel grades, with 304L being a low-carbon version for enhanced weldability.
ASTM A403 WP316/316L/316H: Austenitic stainless steel grades, with 316L being a low-carbon version, and 316Ti offering enhanced high-temperature strength.
Other Grades: 317/317L, 321, 310, 347, 904L, 2205 Duplex.
3. Alloy Steel:
ASTM A234 WP1/WP5/WP9/WP11/WP22/WP91: These grades are used in high-temperature and high-pressure applications.
4. Other Materials:
Nickel Alloys: Monel, Nickel, Inconel.
Copper Nickel: CuNi10Fe1Mn, CuNi30Mn1Fe.
Aluminum, Titanium, etc.: Various other materials are also used for specific applications.
ASME B16.9 is a common standard for buttweld fittings, specifying dimensions and tolerances.
