Tobee 10x8S-GH High Head Gravel Pump is designed for continuously handling the most difficult high abrasive, big particles slurries with extra high head. The wet parts are made of high-Chrome alloys to ensure long service life. GH gravel pumps has far better performance than common gravel pumps in dredging, sand mining, barge loading and mineral processing etc.
Design Features:
GH high head gravel pump is cantilevered horizontal centrifugal pump designed for handling the most difficult higher abrasive slurries which contain too big solids to be pumps by a common slurry pump.
Construction of this pump is of single casing connected by means of clamp bands and wide wet-passage. The wet-parts are made of Ni-hard and high chromium abrasion-resistance alloys.
The discharge direction of pump can be oriented in any direction of 360°.
closed impeller with wide passage, good performance of NPSH and abrasion resistance.
All the wet parts are made of wear resistant high chrome alloy material. They are suitable for delivering slurry in mining, metal melting, dredging, barge loading.
Tobee 18x16TU-GH High Head Gravel Pump is horizontal single-casing gravel pump with wide channel to transfer sands,slurries or gravels with big particle size. The wet parts are made of Ni-hard and high-Chrome alloys to ensure long service life. It has superior performance than common pumps in dredging, sand mining, barge loading and mineral processing etc. With all the advantages of TG Gravel pump,TGH gravel pump has achieved extra high head for special working conditions.
Tobee 12x10G-GH High Head Gravel Pump is the worldâ??s standard pump for dredge and gravel with high pressure applications. The 12x10 pump performance range provides excellent wear life while maintaining efficiency during the wear cycle providing the best total operating cost. A wide variety of shaft seals provide a perfect fit for a wide range of applications. Design Features: Impeller - Pump out vanes on rear and front (on closed impellers) reduce recirculation within pump, and aid in preventing seal contamination NPSH - Exceptional NPSHr conditions due to large impeller eyes Large Particles Large eye openings and vane passages allow for the largest particle flows Expeller (Centrifugal Seal) - Available with low flow water flush or zero flow (grease lubricated) options to provide exceptional sealing where water introduction to the seal is intolerable or limited
Tobee 16x14TU-GH High Head Gravel pump is designed specifically for continuous pumping of extremely aggressive slurries, with a wide particle size distribution. Capable of handling large particles at consistently high head, high pressure results in low cost of ownership. The large volume internal profile of the casing reduces associated velocities further increasing component life. Design Features: Broad path created by single casing and clamp bands connection Unique design to make maintenance and wet parts replacement convenient. The wet parts are made of Ni-hard and high-chrome wear-resistant alloys with good anti-corrosive property. The discharge direction of pump can be oriented in any direction of 360�°. The standard seal type is packing seal. Good performance of NPSH.
Tobee 18x16TU-GH High Head Gravel pump is designed for continuously handling for large particles of slurries, sands, gravels, stones with high head applications, The main wear parts made from high chrome alloy, The hardness can upto 65HRC, Working life is 30% increasing than other common slurry pumps, 18x16 dredge gravel pump widely used for cutter suction dredges, sand dredgers, sand Excavation, sand reclamation, sand barge loading etc. Design Features: 18x16 dredge gravel pumps are designed for gravel and sand dredge from river and/or sea, as well as large particle pass in mining operations. The unique segmented clamp ring on larger size units and solid on smaller pumps,facilitates casing rotation to any angle, reducing the need for costly high wearing bends. Minimal maintenance is required. Impeller expulsion vanes reduce gland pressure and intrusion of high concentrations of solids in the gland area. Efficiency is maintained by minimizing suction side recirculation.
Tobee GH High Head Gravel Pumps are Capable of handling large particles at consistently high head, high pressure, long distance, resulting in lower costs. Casing is designed with a large volume internal profile to reduce associated velocities which prolong component life. Designed to pump extremely aggressive gravels with a wide particle distribution. The GH gravel pump provides excellent wear life while maintaining efficiency during the wear cycle providing the best total operating cost. A wide variety of shaft seals provide a perfect fit for a wide range of applications. Design Features: Modular design for ease of maintenance. Large passage width designed to minimise internal velocities resulting in prolonged wear life. Lifting points for easy maintenance. Standard or advanced bearing assembly improves reliability to extend bearing life reduce lubrication costs. Shaft sealing for increased reliability, stuffing box, expeller, elevated seal or mechanical seal options available.
Supplier: En590 10 , D6 , Naphtha , Jetfuel, Nigerian Crude, Petcoke, and Iron Ore ( Mexico origin )
Buyer: Used/second hand equipment, machinery, plants, granular sulphur
Supplier: Pump pv22, Used Korean Hyundai & Kia engine with gearbox, Organic Fertilizer, Used Volvo And Scania Engine With Gearbox, Arnold Palmer Golf Shoes
Tobee 10/8S-GH High Capacity Gravel Suction Pump with high chrome wear parts which design for handling large particles at river. 10x8S-GH High Head Gravel Pump is designed for continuously handling the most difficult high abrasive, big particle slurries with extra high head. The wet parts are made of high-Chrome alloys to ensure long service life. GH gravel pumps has far better performance than common gravel pumps in dredging, sand mining, barge loading and mineral processing etc. Design Features: GH high head gravel pump is cantilevered horizontal centrifugal pump designed for handling the most difficult higher abrasive slurries which contain too big solids to be pumps by a common slurry pump. Construction of this pump is of single casing connected by means of clamp bands and wide wet-passage. The wet-parts are made of Ni-hard and high chromium abrasion-resistance alloys. The discharge direction of pump can be oriented in any direction of 360 . closed impeller with wide passage, good performance of NPSH and abrasion resistance. All the wet parts are made of wear resistant high chrome alloy material. They are suitable for delivering slurry in mining, metal melting, dredging, barge loading.
double tube hand pump for BIG SUP board TRIPLE ACTION it's more compact and light. It's the best for brands who want to use a pump of triple action as standard equipment in their SUP. The compact piston permits also females and young guys to be able to achieve easily high pressure. HP6, being used in TRIPLE-doublesingle action, can achieve 30psi rapidly and effortlessly. The switching 3-2-1 can be realized easily and comfortably rotating the switch knob. Itâ??s completely customizable for colour, graphic and calibration of gauge meter. Features: · capacity 3.2+3.2L, max. pressure 30psi as DIN EN 16051 · switch knob to change comfortably from triple to double or single seals and anti-sand filter for long life of pump and SUP extra long body and high-airflow piston for an easier inflation pump completely shock-proof, compact and light (1.7kg) · shockproof gauge meter