FEATURES
Most cost-effective
Faster installation
Safe and easy installations
High accuracy 0.5
Holding wire diameter: 32mm
Ratio ranging from 60/1A to 600/5A
CE, UL
PARAMETERS
Technical parameters
Standards IEC/EN60044-1 & IEC61010-1 & IEC61869-2&ANSI C57.13
Ratio 400: 5 or 200:5 , customized
Nominal input current Primary current 100A/150A/200A/300A/400A/500A/600A
Overload withstand 1.2 times rated current continuously
Accuracy 0.2%, 0.5 %, 1%/60Hz
System Voltage 720V(0.72kV)
Output signal 1A or 5A
333mV AC or 100mV-2V optional
Burden 2.5VA
Frequency range 40 Hz-500 Hz
Dielectric strength 3KV 50Hz/60Hz at 1 minute
Output Standard 2.5 meter cable
Max. jaw opening 32 mm
Mechanical parameters
Dimensions (DH) (mm) 110mm130mm 41mm
Weight(g) 700
Operating conditions
Operating temperature -25 C to +55 C
Relative Humidity 0-85% non-condensing
Altitude
KF series
split-core current transformers.
The CT can be mounted to existing panels, such
as control centers or load centers, to measure or monitor voltage. These CTs
can be mounted without removing existing cables for easily installation.
Jiangyin Spark XH-SCT-T24 Series split-core current transformer , Diameter 24mm , Max rated current 300A ,output 0.333V ,1.0% class ,UL list
Features:
Small size, low cost
High secondary turns
Secure locking hinge
Features:
Maximum continuous primary current 5A to 300AAC
Current Ratio: 3000: 1
Output: 0.333 Volt or mA at rated current
Accuracy: �± 1% from 5% to 120% of rated current
Insulation Voltage: 600VAC
Maximum Primary Voltage: 5000VAC(Insulated Conductor)
Phase angle: Less than 2 degrees at 50% of rated current
Frequency Range: 50 Hz to 400 Hz
Operating Temperature: -15C to 60C.
Leads: 4Foot(105cm), UL 1015, Twisted Pair, 0.34 mm2(22AWG)
CE recognized, and RoHS compliant
Output and leads can be customized
DAQGPCT485 split core current transformer is a kind of current sensor transformer which can convert AC analog signal into RS485 digital signal launched by Shanghai Data Acquisition IOT Technology Co LTD The product has builtin 32bit ARM series MCU and highprecision metering chip and is a multipoint calibrated current conversion module It has the characteristics of high precision and fast response DAQGPCT485 can directly interact with common data acquisition gateways DTU programmable controller PLC and host computer
This product is widely used in AC motor lighting equipment air compressor heating ventilation and air conditioning equipment building selfcontrol system equipment OEE open rate industrial Internet rural power transformation projects and other scenarios of current monitoring and acquisition scenarios
2 Service Concept
Our company solemnly promise you
You buy more than just products but also meticulous and thoughtful technical support
We provide free remote guidance remote configuration and commissioning services and send data to the server specified by the customer
Free IOT solution consulting services
3 Product Characteristic Parameters
Line Sequence Definition
Red12V BlackGND Yellow485A White485B
Length of LineDefault 1 meter
Acquisition Characteristic
Current detection range AC 02A100AOther large range transformers can be customized
Electrical Characteristic
Power supply mode524V DC
Operating power consumption05W
Operating frequency5060Hz
Communication Characteristic
Transmission modeRS485
Communication protocol Modbus RTU
Structural Characteristic
MaterialABS plastic housing
Installation methodBuckle mounting
Working Environment
Temperature 20C70C
Storage Environment
Temperature 20C80C
4 The Core Advantages of the Product
High precision measuring chip high measurement accuracy
Open type design easy to install
Easy installation and fast deployment helping IOT projects land quickly
5 Description of the Modbus Communication Protocol
51 Serial Port Communication Parameters
Baud rate9600 Data bit8 Verify NONE Stop bit1
52 Function Code Definition
The upper computer uses 03 function code to read data or receive alarm data
The host computer controls the lower machine equipment transformer using 06 function code
Technical parameters
Standards IEC60044-1; IEC 61869-2; NTC 2205; GB1208-2006; ANSI C57.13
Accuracy Class 0.5S, 0.5%, 1%, 3%
Range of primary rated current 100-1000A
Range of Rated load 10VA
Rated frequency 50/60Hz
Rated secondary current 5A or 1A
Rated short-time thermal current 40kA, 1S
Rated continuous thermal current 150%I1n
Secondary winding power frequency withstand voltage 3kV, 1min
Safety Factor Rating (FS)
1.Features:
Double-screw fastening, safe, easy to install, portable
Wide inner window, allowing clamping of big cables or bus-bars
Wide range of sizes to accommodate all the existing installations
2.Application:
Current measurement, monitoring and protection for electrical wiring and equipment.
Current and power measurement for electric motors, lighting, air compressheating and ventilation system, air-condition equipment and automation - control system.
Current, power and monitoring device.
Relay protection device.
Company introduction
1.certification
We have passed ISO9001:2015,CE,SGS approval and IEC report
2.Company profile
Tianjin Grewin is concentrating on transformers for 20 Years and complianted by ISO9001:2015,CB,IEC CB,CE etc.We're always pay great attention to its business philosophy "Quality and Honesty First".Grewin is specialized in the design and manufacture of wound components such as transformer,current sensors, chokes etc .windely used in communications,electronics,meters,industrial control,medical equipments and other fields.We are also a provider of power meters and instruments locators. 85% of its products exported to America, Europe, and Asia etc.We sincerely invite you to join us to create a bright future.
3.Shipping:
(1)Products are shipped via UPS / DHL / EMS / HK EMS / FedEx / TNT and so on expresses (door to door).
(2)We Provide Drop shipping Service.
(3)20 days around delivery upon receiving payment if the qty is lower than 1000PCS and it is not customized products.
(4)Shipping via EMS. UPS. FedEx and TNT express usually takes 3~7days dependent on the destination country.
4.Payment terms:
(1)T/T 100% or 50% deposit by T/T in advance, balance amount to be paid 7 days before delivery.
(2) By irrevocable L/C at sight, to be issued immediately against confirmed order.
(3)Payment by T/T, if order amount is less than USD 20,000.
5.Warranty:
(1)We provide 1 year warranty.
(2)If the product is defective, please notify us within 3 days of delivery.
(3)All products must be returned on their original condition, in order to qualify for a refund or exchange of goods
From 100A~6000A , Secondary current could be 5A 1A ..
Features:
.High quality compressivemeasurements
.Available in a wide range oftransformer ratings
.Accuracy up to Class 0.5
.Foot or burbar mounted
TypicalApplication:
.Switchgear
.EnergyManagement Systems
.InstrumentationEquipment
.SplitCore Current Transformers are designed for assembly to an existing electrical installation no needto dismantle the primary busbar or cables.
The KCT range of split core current transformers have been specifically designed to be small CT and easy to open and yet
maintain the accuracy required for kwh meters. The benefit of a split core current transformer is that it can be placed
into position easily and without disturbing or disconnecting the main cables it is monitoring.
