Silicon 60,000 Cps

Supplier: Copper sulphate 24.5%, manganese sulpahte 32%, cobalt sulphate 20.5%, ferrous sulphate 19% & 30%, ammonium molybdate 54%, zinc sulphate mono 33% & hepta 21%, magnesium sulphate 9.6%, boron 20%, boric acid, borax decahydrate 10.5% & pentahydrate 15%, water soluble fertilizers, potassium schoenite, edta chelates(zn, mg, mn, cu, ca, fe), amino acid 80% & 50%, amino cheleted mix, (zn, cu, ca, mn, mg, fe), humic acid granular 80%, potassium humate flakes 98%, potasium fulvic humate 98%, humic acid powder 95%, potassium humate crystal 98%, potassium fulvic humate 98%, seaweed extract powder/flakes, fulvic acid 81%, silicon super spreader, glycine cheleted mixture (cu, mn, cr, zn), choline chloride 50%, 60%, 75%, 98%, bypass fat 84% & 99%, yeast extract powder, beef extract powder, peptone, dextrose monohydrate.

Ferro silicon magnesium Spec.: si: 40-44% al:1.2% max mg : 5.5-6% ca: 2.0-3.0% re: 0.5-2.0% Size: 5-25mm Quantity: 300mt/month Packing; 1mt big bags

Ferro silicon Spec.: si: 75% min al:1.5% max c : 0.2% max s: 0.03% max p: 0.08% max Size: 10-100mm 90% min Packing: in 1mt big bags

Silicon metal Spec.: si : 99% max fe : 0.4% max al: 0.4% max ca: 0.1max Size: 10-100mm 90% min Size: 10-100mm 90% min Packing: in 1mt big bags

Platinum cure molding rubber silicone rtv Strenghts for platinum cure molding rubber silicone rtv Platinum cure molding rubber silicone rtv is used for prototyping and the reproduction of parts. Silicone moulds can be constructed in many different forms depending on the shape of the part you are making. In this section we will outline how to create the easiest one part flat back mould. Why platinum cure molding rubber silicone rtv Silicone is the first choice of material when casting 3 dimentional shapes that contain undercuts as it exhibits excellent release properties, a high level of surface detail, very good chemical and high temperature resistance. It comes in a two-component system (base + catalyst) available in a hardness range of very soft to medium. It is available for making moulds that are poured, brushed or sprayed Features of platinum cure molding rubber silicone rtv 1. Good characteristics of easy-operation 2. Light viscosity and good flowability 3. Low shrinkage 4. Favorable tension 5. No deformation 6. Favorable hardness 7. High temperature resistance, acid and alkali-resistance and ageing resistance 8. Food grade, non-toxic Datasheet of platinum cure molding rubber silicone rtv ModelColorMixing ratioPot life (mins)Demouled time (hrs)Hardness(a0)Tensile-strength (kgf/cm2)Tear-strength (kgf/cm)Viscosity (cps)Elongation (%) Hy-e625Translucent1 : 130-604±125±235±225±26000±3000=400 Hy-e630Translucent1 : 130-604±130±240±223±27000±3000=395 Hy-e635Translucent1 : 130-60 4±135±247±2 22±28000±3000 =470

Black color pcb electronic potting silicone hy-215   Technical parameters for pcb electronic potting silicone Properties indexPart aPart b Before curingAppearenceBlack fluidColorless / yellowish fluid Viscosisty (cps)2500±500- Features when operationMixing ratio ( by weight)10:1 Operating time (25c /min)20~30 Curing time ( hr, basically cured)3 Curing time ( hr, perfectly cured)24 Hardness(shore a)15+/-3   After curingThermal conductivity[w( m·k)]=0.4 Dielectric strength( kv/mm)=25 Dielectric permittivity(1.2mhz)3.0~3.3 Volume resistivity(o·cm)=1.0×1016 Fire resistance94-v1    (pls note all data of  pcb electronic potting silicone rubber with black color above is in 25c with 55% humidity conditions. We don't guarantee a same date if testing under different conditions, or when data was regenerated).   Warm tips for for pcb electronic potting silicone  1. Sealing pakage for storage. The mixture should be used up at once to avoid wasting.  2. Silicone belongs to non-dangerous goods, but keep away form mouth and eyes.  3. When it gets stratified after a period of storage, please mix hy-210# evenly before using,       it does not affect the performance.     Shelf life and transportation 1. Twelve(12) months when stored at 25c in original unopened packages. 2. This is a non-dangerous product, it can be transported as general chemicals. 3. Products exceed the storage life should be confirmed normal before using.

1. 1:1 addition type, good adhesive strength and self-healing 2. High elongation, excellent flexibility for mechanical stress relieving 3. Low oil penetration after cured, good anti-poisoning property 4. Good dielectric in high temperature for high voltage protection 5. Excellent aging resistance and weatherability 6. Excellent waterproof, corrosion prevention, moisture proof and chemical media resistance Used for encapsulation of various modules, semi-conductor, IGBT, automotive ECU module, IC chip, weighing sensor, waterproof connector. PROPERTY STANDARD/UNITS VALUE of SI2709 ---- ---- PART A PART B Material ---- Polysiloxane Hydrogen polysiloxane Color Visual inspection Colorless Liquid Colorless Liquid Viscosity 7;C, cps 800~1000 800~1000 Density 7;C, g/cm3 0.99 0.99 Mixture/mass ratio ---- A:B=100:100 Viscosity of mixture 7;C, cps 800~1000 Operation time 7;C, min 60 Cure condition RTV or HEAT 7;C /6 hour;67;C /30min Cured appearance ---- Colorless transparent gel Needle penetration 1/mm 75 Dielectric strength KV/mm 25 Volume resistance DC500V, ohm-cm 1.0¨¢1015 Loss factor 1 MHz88;0.001 Dielectric constant 1 MHz 2.8 Application temperature7;C -60~260 Part Aa10 KG/Bucket, Part Ba10 KG/ Bucket.

Zs-nj-d959w is one kinds of one-component flame resistance and thermal conductive silicone sealant at room temperature curing. With good adhesion for pc/abs, various metal such as alumina, copper, stainess steel, etc. Keep continuous stable property at the temperature range of -60?~200?. During the curing process, it will release the alcohols, which no corrosion to the materials such as polycarbonate(pc) and copper. Completely complied with rohs of eu directive. Https://www.Alibaba.Com/product-detail/flame-retardant-ul-94v-auto-vehicle_60550509931.Html

1. Application of liquid silicon rubber for toe spreaders: The product is a two component high elongation silicone gel designed for silicone food care products, such as silicone insole.Q This product cured at room temperature to a soft track gel with the addition of curing agent. The soft nature and cushioning effect offer this product provides excellent protection for our food health care. 2. Aadvantages of liquid silicon rubber for toe spreaders: 1. High transparency.  2. High fluidity, high curing rate.  3. Pressure release.  4. Shock absorption.  5. Multiple density 3. Datasheet of liquid silicon rubber for toe spreaders: Model Q625# Q630# Appearance Transparent Transparent Mixing Ratio 1:1 1:1 Operating time (Mins 25¡ãC) 30 -50 30 -50 Curing time (H 25¡ãC) 3 - 5 3 - 5 Curing time (Mins 60¡ãC) 20 - 30 20 - 30 Hardness (A¡ã) 25¡¨¤2 30¡¨¤2 Density ( g/cm 3 ) 1.08 1.08 Viscosity (CS) (After mixed) 8000 ¡¨¤ 500 8500 ¡¨¤ 500 Tensile-strength( kgf /cm2 ) 45 ¡¨¤ 5 45 ¡¨¤ 5 Tear-strength (kgf /cm2 ) 14 ¡¨¤ 2 17 ¡¨¤ 2 Elongation-break(%) 450 ¡¨¤ 50 400 ¡¨¤ 50 Retractility(%) ¡¨¹0.1 ¡¨¹0.1        4. Package and storage of liquid silicon for  Toe Spreaders: 1). 20kg or 200kg /drum. 2). It is a kind of non-dangerous goods, and it should be stored at a cool and dry place, please keep it from sun and rain.     Place of Origin: Guangdong China Brand Name: Hong Ye silicone rubber Minimum Order Quantity: 200 Kilogram Delivery Time:  within 3 days after payment confirmed in our bank. Supply Ability: 8 Tons per Day  Payment Terms: L/C, T/T, Western Union Price Terms: FOB, EXW, CIF, CNF Packaging Detail: 1kg/Jar,5kgs/Jar,20kg/drum,25kgs/drum,200kgs/drum Further information for silicon  Toe Spreaders, please feel free to contact Miss COCO: Website: http://www.szrl.net Tel: +86 -0755-89948294 FAX: +86-0755-89948030 5kg/pail; 20kg/pail; 25kg/pail; 200kg/pail