1.Wallputty/ skimcoat ( white) 2.Rangeela putty (available in pink, light green, yellow and off white) 3.Crack fillers 4.Gyp + gypsum plaster ( hand and machine application ) 5.Ready mix plasters ( rmp ) 6.Block jointing mortars ( bjm grey cement based ) 7.Tile adhesive ( grey and white cement based ) 8.Master plaster 9.Plasto seal 10.Plasto proof 11.Lime plast 12.Quick bond
Provides protection to tyre buffed against oxidation, provide excellent green tack, better cured bonding between casing and cushion and has quick drying property.
Description: VFLOOR1 is a single component Cementitious Self Leveling Mortar. Once cured, it provides a smooth, level surface on which to install a variety of floor coverings. Suitable for prepairing interior floors prior to laying parquet, vinyl sheet and tile, soft floor covering, natural stone, ceramic tiles, etcâ?¦ It can be used on a wide range of absorbent and non-absorbent floor surfaces including concrete, cement and sand screeds, terrazzo, asphalt, ceramic & quarry tiles. Layer-thickness 2-10mm Can be pumped Standard primers give excellent bonding to the VFLOOR1 products Product name VFLOOR1 Compressive strength >40 Mpa, 28 days later Flexural strength >8 Mpa, 28 days later Application temperature 5-30 degree Mixing ratio 20kgs powder + 5.2kgs Liquid Product name PRIMER Mixing ratio 2kgs Primer + 2L water + 4kgs cement Feature & Benefits: - Single component, just mix with water - Good adhesion to primed substrates - Good flow, self smoothing - Rapid setting and early strength - Easy and quick to lay Mixing: Add clean water to suitable mixing bucket. Mix slowly and continuously to form a homogeneous mixture. - VFLOOR1 20kgs barrel required approximately 5.2 litres of clean water The mixed materials is immediately ready to use and should be used within 30-40 minutes after mixing. Ready for foot traffic after approx. 3 hours. Drying time: Prevent draughts across the floor to avoid localized premature drying At ambient temperature, VFLOOR1 will appear to be dry after approximately 24 hours. Floor laying may commence after 48 hours. Coverage: - At an application thickness of 2mm the coverage will be approx. 5kgs per 1m2 Shelf Life: 9 months.
FOB Price: US $20.0 - 1000 / Set Min.Order Quantity: 1 Set/Sets Supply Ability: 200000 Set/Sets per Year Port: Tianjin Xingang, Shanghai Port, Ningbo Port Payment Terms: L/C,T/T,Western Union,MoneyGram Quick Details Standard or Nonstandard: Standard Structure: Gate Pressure: Low Pressure Power: Manual Material: Casting Temperature of Media: Normal Temperature Media: Water Port Size: DN50-DN600; 2"-24" Place of Origin: Hebei, China (Mainland) Model Number: FM UL strainer(filter) Brand Name: PYL Application: General Product name: 20bar 300psi AWWA FM UL listed ductile iron flange Y strainer Standard of product: BS/ANSI fire FM & UL gate valve Working pressure: 175PSI, 200PSI, 250PSI, 300PSI gate valve Usage of product: Fire protection gate valve Certificate: FM / UL Coating of product: Red/ Blue Working Temperature: -10-200 graphite gasket; 0-80 rubber gasket Nature of company: Manufacuturer of FM UL filter Connection Ends: Flange to ASME B16.1 CL 125 Coating: Fusion bonded epoxy coating in accordance with ANSI/ AWWA C550 Packaging & Delivery Packaging Details: Generally we use the wooden box and wooden pallet with plastic and also we use the Woven bag. In addtion, we can change the shape of the packaging according to customer requirements. Delivery Detail: Shipped in 30 days after payment The main vlalve products of our company include (1) ANSI gate valve, DIN gate valve, GOST gate valve, Soft sealing gate valve, Knife gate vave, Flat gate valve (2)Wafer type butterfly valve, flange type butterlfy valve, single eccentric butterfly valve, double eccentric butterfly valve, Three eccentric buterrfly valve (3)Check valve, lift check valve, swing check valve, wafer type check valve, spring check valve (4) ball valve, tee ball valve, 4 way ball valve, welding ball valve (5)strainer, filter, Y type strianer Materials WCB A216 ; Q235,ST37 ; LBC/LCC ; WC6/WC9 ; WCC ; CA15 A217 ; M-30C ; H.B/H.C ; HT250/GG25 ; GGG40 ; SS304 ; SS304L ; SS316 ; SS316L THE MAIN TYPE AND MATERIAL OF OUR VALVE
BuildWell Quickbond is a admixture of sand, cement and superior quality polymers. It is a bonding agent that enables quick preparation of ceiling and RCC wall surface. Also offers the dual benefits of mechanical and chemical bonding, which eliminates the labor – intensive hacking and reduces debonding losses. Features : - Excellent bonding. - No hacking is required on RCC wall. - Hence prevention of microcracking and saving of labor cost. - Strong chemical and mechanical bond - Easy to use. - Works good for Gypsum plaster as well for cement sand plaster Benefits : - Can be easily applied by brush. - Reduces hacking. - Time saving. - Less rebound loss while plastering. - It is water soluble product hence no solvent odour. - Fast drying. - Improves bonding strength between RCC wall and Plaster.
Description A cost effective product that is designed for High Quality Fast drying Enamel for Automobile with enhanced good bonding capabilities. It gives high gloss and good colour retention. Unique Features & Benefits Excellent durability Good dry time, enabling quick handling. Product can be applied by spray or brush coats. Excellent flow characteristics to form smooth and uniform finish Excellent coverage Good corrosion Resistance Good weather and water resistance
Description A cost effective product that is designed to eliminate porosity leaks on ferrous & non-ferrous castings with enhanced bonding capabilities. Unique Features & Benefits Excellent durability Permanently seals small holes inherent in castings. Good dry time, enabling quick handling. Product can be applied by dip, spray or brush coats. Excellent flow characteristics to form smooth and uniform finish Excellent coverage Good corrosion Resistance Good weather and water resistance
DESCRIPTION Bituminous Primer is product containing oxidized bitumen and a mix of technical quick drying solvents. APPLICATION Bituminous Primer is recommended to block the dust and the porosity of concrete surfaces allowing the quick application o f the bituminous polymer membranes, both with flame application and cold bonding with bituminous sealants or with self adhesive membranes.Bituminous Primer allows quick film drying, has an excellent penetration and adhesion to the support for the absence of surface stickiness. INSTRUCTIONS FOR USE Concrete surfaces must be dry, clean and free from oil, dust or release agents. This type of primer is ready for use after mixing it. Bituminous Primer can be either sprayed or applied by means of roller or brush. In case of hot application of membranes with flame, the primer can be used only if surfaces are completely dry. On the contrary, if the surface is damp, it is recommended to use a bituminous primer specific for damp surfaces. The drying time depends on concrete porosity, on the quantity of product applied and on the temperature of both the surface and the environment. Usually the film gets dry after 2-4 hours from the application. The drying time can increase in case of cold temperature and with low a bsorption surfaces. PACKING 5 gallon Bucket SHELF LIFE The product can be stocked in closed buckets and in dry area, far from UV rays for 12 months. TOOL CLEANING After use clean tools with common solvents.
This hose is made from extruded thermoplastic polyester based polyurethane (TPU) with excellent wear & tear properties. The reinforcement is made from circular woven filament polyester yarn. The "extrusion through-the-weave" production method gives a very strong bonding between cover and lining. Construction: Tube: Thermoplastic polyurethane(TPU) Cover: Thermoplastic polyurethane(TPU) Reinforcement: High Strength Circular Woven Polyester Or Polyamide Characteristic: Extra abrasion resistance, oil resistance Acid and alkali resistance, corrosion resistance Cold resistance, small flow resistance Low coil volume for easy handling Flexible in all weather conditions from -50 to +80 deg C Temperature: -55 -131 ) to 80 (+176 ) Application: TPU drag hose is designed for distribution of slurry and manure as fertilizer,Delivery of water in self-propelled machines for irrigation, As for the superior abrasion resistance, the TPU drag hose is designed for distribution of slurry and manure as fertilizer, delivery of water in self-propelled machines for irrigation. Oilfield plot fracking, construction sites, waste water industry, agriculture and mining, transport of abrasive materials, flexible pipeline even in extreme terrain, irrigation and sludge disposal, for heavy duty service under toughest conditions. Perfectly prepared for hydraulic fraction in shales and oil fields. TPU Hose purpose-builds the products that are tough enough to meet the rigorous demands of the oil and gas industryâ??from fracking operations to dewatering applications. Our hoses are light in weight for quick and easy transport, yet are engineered with extra-sturdy abrasion-resistant hose walls that kink less and provide smooth, unrestricted flow for exceptional performance in the field. Constructed with high tenacity fibers and an extremely abrasion resistant thermoplastic polyurethane (TPU). Polyurethane is excellent for wear and tear resistance, the reinforcement is made from circular woven filament polyester yarn. In recent years, TPU hose is widely used in oilfield fracking project, it has been demonstrated worth of the price compared to the life of nitrile rubber/PVC hose for water transfer in the oil patch.
