It is one of the most important machines in mills and used to grind all kind of grains according to diagram. Single or double designs are available according to request and diagram. Single roller mills contain 4 rolls in parallel with double design roller mills contain 8 rolls. It may be produced as 1000mm length however 600mm, 800mm and 1250mm models are available depending on request or diagram.
-Reinforced 16mm plate-body thickness.
-G22 steel cast-iron bearings.
-Vibration rubbers under bearing slides made from special strong rubber.
-Sustained tense Poly V belts thanks to self-tension pulley system.
-Reinforced slide system provides easy maintenance and roll changing in a short time.
-Motor drive mechanism by sensor operates according to product density.
-Feeding roll system may be adjusted manually.
-Easy maintenance and cleaning thanks to removable side hatches and complete convertible lift gates in front of panel system.
-Special compressed pulleys provide easy assembling and disassembling.
-Excellent roll surface cleaning by guarded and hermetically sealed brush.
-Product inlet point aspiration system.
-Protection system by sensor against to filled bottom hopper.
-Product contact surfaces and inner sides are made of epoxy painted according to Codex aliment Arius however aluminum and SS are available depending on requests.
-Manual rotational system for roll adjustment.
-Bearings are ZKL.
-Pneumatic System is MAG.
-The roller mills are designed according to CE standards as minimum noise and vibration.
Vertical roller mill roller body wear Reasons: 1. Subject to frictional pressure between roller, material reaction force, friction between material and roller liner 2. The mutual effect of the material grinding angle on the shear stress of the grinding roller, the hydraulic system pressure of the roller mill and the apparent compressive stress of the vertical mill Fault: Once there is a matching clearance, impact collision will occur between the body and the lining, which will increase the wear between the body and the lining. In severe cases, the lining will crack or even break, causing the lining to fall off, the machine is damaged, especially the deceleration. Damage to the machine, causing a vicious incident. Solution: Developed countries such as Europe and the United States use polymer composite materials for rapid repair of vertical roller wear, among which the Fushui Blue series is relatively mature. The material is satisfactorily solved with its excellent mechanical properties and good plasticity. It not only prolongs the service life of the equipment, improves the productivity, but also avoids the secondary possibility of the problem, and avoids the additional downtime of the shutdown, and escorts the safe and continuous production of the enterprise. Vertical roller mill wear chamber wear Reason: 1. There is a gap between the bearing and the bearing chamber 2. Bearing heating will lead to bearing sintering Solution: 1. Traditional soldering brush plating method, there are certain drawbacks: repair welding will cause thermal stress, bearing material damage, severe deformation or even break; brush plating pollution is heavy, and coating thickness is limited, application Subject to greater restrictions. 2. The processing of polymer composite materials can ensure the matching of the repaired parts and the matching parts to the utmost extent, and avoid the secondary wear caused by the increase of the gap.
Product descriptions about YGM8314 Raymond Roller Mill: Clirik YGM8314 Raymond grinding mill, Raymond mill is suitable for processing various non-flammable and non-explosive mineral materials with Mohs hardness less than 9.3 and humidity less than 6%, it is widely used in the fields of metallurgy, construction, chemical industry, mining, highway construction etc,. The granularity of the finished powder size can be adjusted between 50 and 325 mesh (315-45 micron). Examples of processing materials include quartz, feldspar, barite, calcite carbonate, limestone, talc, ceramic, iron ore, carborundum, bauxite, rock phosphate, coal and other materials, total about 400 kinds of materials. Features of YGM8314 Raymond Roller Mill: YGM8314 Raymond grinding mill, Raymond mill has the similar working principle as High pressure suspension grinding equipment, but its grinding device is fixed with 1000-1500kg pressure springs. When the machine works the grinding roller, which under the action of high pressure spring and centrifugal force, rolls close up to grinding ring, its rolling pressure is 1.2 times higher than that of High pressure suspension grinding equipment given an identical condition and its capacity increase 20% to 30%; When the grinding roller and grinding ring, stable capacity and fineness are guaranteed. Operating Principle of YGM8314 Raymond Roller Mill: Big materials are crushed by jaw crusher to the required particle sizes, and carried by bucket elevator to the storage hopper, and are fed evenly and continuously by vibrating feeder into the main unit for grinding. The grinded powder are carried by the airflow from the blower to the classifier to be classified, the particles which meet the fineness enter cyclone collector through pipe, and are separated and collected there. They are discharged at the discharging valve to become finished products; the airflow is sucked to the blower by return pipe on the top of cyclone collector. The whole airflow system is a sealed circulation, and is circulated under positive and negative air pressure. Features of YGM8314 Raymond Roller Mill YGM8314 Raymond grinding mill, Raymond mill has the similar working principle as High pressure suspension grinding equipment, but its grinding device is fixed with 1000-1500kg pressure springs. When the machine works the grinding roller, which under the action of high pressure spring and centrifugal force, rolls close up to grinding ring, its rolling pressure is 1.2 times higher than that of High pressure suspension grinding equipment given an identical condition and its capacity increase 20% to 30%; When the grinding roller and grinding ring, stable capacity and fineness are guaranteed.
ModelGrinding Table Diameter (mm)Roller Diameter (mm)Roller Number (n)Motor (kw)Output (t/h) GRMK30.313,0001,6003125055~60 GRMK32.313,2001,7003160065~80 GRMK35.413,5001,8004180085~100 GRMK40.414,0001,90042500115~125 GRMK43.414,3002,12043000135~145 GRMK46.414,6002,24043350150~160 GRMK48.414,8002,24043550170~180 GRMK50.415,0002,36043900190~200 GRMK53.415,3002,50044600210~230 GRMK56.615,6002,50065300235~250 Packaging Details:Standard Container Delivery Detail:30 Days
ZY Series Micro Powder mill Product introduction ZY series micro-powder absorbs modern grinding technology, based on the development trend and demand of the domestic mill market, and is a new equipment for ultra-fine powder processing users. It is widely used in processing materials such as limestone, calcite, calcium carbonate, dolomite, barite, talc, gypsum, wollastonite, carbon black, activated carbon, kaolin etc, which are mohs hardness below 7 and the moisture.
Intorduction of Ultra Fine Vertical Roller Mill Brand: Clirik Model: CLUM Application: Micro powder vertical roller mill are suitable for huge capacity producing, widely used in grinding non-flammable and non-explosive materials under 7(the Moh's hardness), such as quartz, feldspar, calcite, talcum, barite, fluorite, iron ore, copper ore quartz, especially for slag, cement clinker, zircon sand, fly ash and carborundum, coal, etc. Input Size: Below 25 mm. Output Size: Could be adjusted between 300-3000 mesh. Capacity: According to your fineness choose, the capacity is about 0.2-45 t/h. Ultra Fine Vertical Roller Mill Working Principle The grinding disc is driving by motor through reducer. The material falls to grinding disc from the feed opening. The materials are driven to the edge of disc by the centrifugal force and crushed into fine powders by rollers. Then, the hot air from the nozzle take the fine powder to high effiency classsifer.The qualified powder are taken by the air to the powder collector to be collected, while the unqualified powder are sent back for regrinding.
Vertical Roller Mill Wear Parts Roller Tyre High Chromium Content Roller Shell Model: LM, CLUM, ZGM, HRM Material: High chromium cast iron Application: Widely used in metallurgy, electric power, cement, chemical, ceramics, non-metallic minerals, power plant desulfurization, water slag, slag, slag, coal, cement clinker, glass, quartz, limestone and other industries for large-scale material grinding and ultra-fine powder Grinding. Advantages of Vertical Roller Mill Wear Parts Roller Tyre High Chromium Content Roller Shell 01 High hardness, grinding a variety of materials High hardness, Rockwell hardness (HRC) up to 65 degrees, can grind pyrophyllite, calcite, limestone, quartz, gypsum, slag and other materials. 02 Anti-cracking, wear-resistant, overload It adopts high-chromium cast iron grinding material and exquisite metal casting technology. It has good size and crack resistance, good wear resistance and strong load bearing capacity. It has no cracking for 20 years. 03 Factory price sales, cost-effective We promised a price of 3,000 yuan per ton than the original or original offer! 04 High-level production After the factory has passed 17 professional inspections, the quality inspection system is strictly implemented, and the output is high.
We are pleased to introduce Piyali Engineering Corporation, located in Delhi, India. We are leading manufacturer and supplier specializing in the production of Sponge Plant DRI (Direct Reduced Iron) equipment and vital components for steel plants, alongside catering to a diverse range of industries including sugar mills, cement plants, fertilizer plants, chemical plants, coal washeries, activated carbon plants, and ball mills. With a strong focus on quality and innovation, Piyali Engineering Corporation stands as a trusted provider of cutting-edge solutions across various industrial sectors. With a wide range of offerings and a strong customer base, we have been serving the industry for several years. Our product range includes various capacities of DRI kilns and coolers, ranging from 50TPD to 600TPD & 900TPD, along with components such as support rollers, pinions, shafts, shells, combined bearing housing complete assemblies, spring plates, Ball Mill Pinion Shaft, Mill Head End Cover for Ball Mill Manufacturer, girth gears, and more. These offerings are designed to meet the needs of Cement Plants, Power Plants, Steel Plants, Sponge Iron Plants, Chemical Plants, Fertilizer Plants, and various other industries. Explore top-notch Lime Kiln Paper Mill Equipment at Piyali Engineering Corporation for customized, cost-effective solutions. Our commitment to excellence ensures reliable expertise and high-quality equipment, guaranteeing seamless Paper Mill operations. Specializing in Rotary Pulp Dryers, we provide comprehensive solutions for your paper manufacturing needs. Choose Piyali Engineering Corporation, your trusted manufacturer and supplier of Rolling Mill Equipment including, Mill Roll Stands, Roll Chocks, Roll Bearings, Rolling Mill gear Universal couplings, Gearbox parts, Chain sprockets & Plummer blocks and more. Our excellence ensures seamless Rolling Mill operations. Our commitment to excellence guarantees seamless operations for industries with reliable equipment and top-notch services. At Piyali Engineering Corporation, we prioritize quality and strive to deliver products that meet and exceed customer expectations. Our adept and seasoned team is deeply committed to providing unparalleled service and ensuring utmost customer satisfaction.
Application of vertical roller grinding mill equipment: Vertical roller grinding mill equipment are suitable for huge capacity producing, widely used in grinding non-flammable and non-explosive materials under 9.3(the Moh's hardness), such as quartz, feldspar, calcite, talcum, barite, fluorite, iron ore, copper ore quartz, especially for slag, cement clinker, zircon sand, fly ash and carborundum, coal, etc. Advantages of vertical roller grinding mill equipment: 1. Grinding mill equipment in the market designed as a cement grinder and not a modified raw mill 2. Simple layout and fewer machines in the mill circuit ensure high run-factor and low maintenance costs 3. Roller and table profile improve operating stability and reliability 4. Special design features for iron removal during grinding minimize wear 5. Optimal wear protection on all internal surfaces extends lifetime 6. Flexibility to operate with reduced number of rollers guarantees long-term availability 7. Segmented roller wear parts made of the hardest possible material without the risk of cracking; very suitable for hard facing 8. High grinding efficiency: save 20~30% power consumption compared with the ball mill. With the increasing of moisture content, it can save more and more electricity. Working Principle of Vertical Roller Grinding Mill Equipment: The grinding disc is driving by motor through reducer. The material falls to grinding disc from the feed opening. The materials are driven to the edge of disc by the centrifugal force and crushed into fine powders by rollers. Then, the hot air from the nozzle take the fine powder to high efficiency classifier. The qualified powder is taken by the air to the powder collector to be collected, while the unqualified powder is sent back for regrinding.
The biggest Grinding machine in the Asia HD2500 Raymond grinding mill grand launched Breakthrough the bottleneck of the grinding mill The greatest capacity grinder of Asia alone The processing capacity of each machine is 60t/h The processing capacity is 30% high than the capacity of the R type Raymond mill. The first choice for large scale ore non-metal powder processing The production fineness is 80-400 meshes Features 1.Reduce the roller and vibrate and improve the production volume according to the calculation, Regarding to the HD series grinding mill, under the sufficient grind force, the rollers is reduced and the grind space can be increased, The material layer filled better between the roller and ring, the attrition between rollers and rings is low, and the  vibration and noise are also reduced, at the same time, the  resistance of airflow of the fan becomes less. Winds can flow freely, thus the winds increase greatly, which determines the increase in the production volume. The production volume is 20% to 30% higher than R Raymond mill. 2.The increase mechanism of linkage pressure of the rollers, which greatly prolongs the useful life of the equipment and increases the capacity by 20% under the same power. 3.With the original roller assembly, the oiling time increased 6 - 15 times, archive the application of oil once, use for 30-45 days 4.High efficiency and stability, the ring and roller always contact during processing, the efficiency and stability of the grind are improved 5.Higher Accuracy powder Classify, without coarseness missing, Variable frequency Squirrel cage classifier�Patent product� is adopted, the accuracy is 80-600 meshes. The classify efficiency reached 99%. The powder selection is stable and adjustable, compare with the blade type, it can greatly improve the powder selection efficiency and qualification rate of the Final product. 6.High efficiency and energy-saving centrifugal blower, the blower is crucial in the operation of Grinding mill, the HD series grinding mill adopts the high efficiency Impeller type energy-saving blower which efficiency is highly improved than straight blade fan. 7.Low noise and vibration: with the reasonable set of Collocation of above, the HD series has the advantages of high production, high qualification rate Low noise and vibration in grinding of the 325-400 meshes. 8.It's applied to the non-metallic non-flammable non-explosive minerals with water content less than 6% and the Moh's hardness under 6.