Indonesian Slack Wax (Cas No: 64742-61-6)

Slack Wax, minimally refined paraffinic wax obtained from the dewaxing process of base oil lubricants. It is used in a wide range of applications, including as a blending component in the production of paraffin waxes, as a waterproofing agent, and in the manufacture of candles, rust protective products, and board sizing.

Slack Wax

TTT procedure: EN590 10pm price $460/MT, Jet fuel A1 price $76/BBL (1) FREE ON-BOARD TRANSACTION PROCEDURE - (TANK TO TANK). Rotterdam, Houston, Fujairah, Jurong, Ningbo-Zhoushan 1. Buyer issues an official ICPO with the seller's procedure, passport copy, banking details along with their Tank Storage Agreement "TSA". 2. Seller issues their Commercial Invoice "CI" to the buyer, Buyer signs and returns the commercial invoice to the seller along with an Acceptance Letter of the sales and purchase procedure. 3. Seller verifies the buyerâ??s storage facility and their Tank Storage Agreement (TSA) with the port authority. (NB: Seller will issue a Tank-to-Tank Injection Agreement (TTIA) to be signed by all parties only if buyerâ??s TSA is engaged, not active or cannot be verified with the local port authority). 4. Seller issues all POP documents below to the buyer upon a successful verification and approval of the buyer TSA or after receiving the TTIA fully signed by all parties: a. Injection Report. b. Product Passport. c. 24 Hours SGS Report. d. Product Certificate of Origin. e. Tank Storage Receipt (TSR). f. Authorization to sell and collect. g. Unconditional Dip-Test Authorization. h. Product Title Holder Transfer Agreement. i. NCNDA/IMFPA. 5. If required buyer may inspect by SGS (Dip Test In Tanks) at buyerâ??s expense. 6. Upon successful verification of POP or Dip Test in the sellerâ??s tank, buyer provides Tank Storage Receipt (TSR) to seller in order to issue the scheduled Injection Programming (IP) to be signed by buyer storage facility and then injects the product into buyerâ??s tanks. 7. Buyer makes the payment for the product via MT103, seller transfers the Title Holder & Ownership of the product to the Buyer. 8. After successful Trial Lift (First Lift), Seller issues SPA/Contract for 12 months with R&E to Buyer for processing. 9. Seller pays commissions to all intermediaries involved, for the initial lift and all subsequent lifts according to the signed NCNDA/IMFPA.

Available stock in Rotterdam tank farm for jet fuel A1: CI DIP AND PAY FOB PROCEDURE 1. Buyer sends ICPO, Company Profile along with current and valid TSA company registration certificate+ buyer passport number + company profile to seller on receipt of seller's soft corporate offer. 2. Seller issues commercial invoice of the product in tanks at the port of Rotterdam and returns commercial invoice. 3.seller will provide the Proof of Product (PPOP) documents for product verification Which include ï?¼ Tank Storage Receipt (TSR) ï?¼ Certificate of origin ï?¼ Statement of Product Availability, ï?¼ Authorization to Verify (ATV), and ï?¼ Dip Test Authorization (DTA) Letter. 4.After successful verification of the PPOP, the buyer will contact the seller's Tank Storage Company to request a 1-day payment invoice to enable Buyer obtain all the necessary authorization and clearance for a Dip Test schedule. *Or* Buyer must have a minimum of 10 days TSR to avoid one day tank extension. 5.Upon a successful Dip Test conducted in the seller's tanks, the buyer will make the payment for the total product cost based on the SGS Report via MT103. The seller will transfer title ownership to the buyer and send all exportation documents. The buyer can then either transfer the product into a vessel or take over the seller's tanks for further storage. 6. Upon a successful Dip Test conducted in the seller's tanks, the buyer will make the payment for the total product cost based on the SGS Report via MT103. The seller will transfer title ownership to the buyer and send all exportation documents. The buyer can then either transfer the product into a vessel or take over the seller's tanks for further storage. 7. All intermediaries involved in the transaction will sign a Non- Circumvention, Non-Disclosure Agreement (NCNDA) and International Master Fee Protection Agreement (IMFPA). These documents will be forwarded to the seller for endorsement, and the seller will provide the Endorsed NCNDA/IMFPA and Authorization to Sell and Collect (ATSC).

Bitumen Primer * Bitumen Primer is Bituminous air curing ready mixed Acid & Alkali resistant special primer. Application * Concrete surface must be clean, dry and rough. No primer should be applied over smooth and wet surface. * After cleaning the concrete surface, one coat of Bitumen Primer should be applied with brush and allow to dry thoroughly. * The drying time will depend upon the temperature. * 24 Month at the temperature 30C (+2OC) Packing * Bitumen Primer: 25 Liter Drum Note * Bitumen Primer contains volatile and slightly toxic solvent. Keep away from spark and open flames at working area. * Bitumen premier it is manufactured using bitumen solution which is used for sealing of prime porous and non-porous surface, and also to protect residential and commercial building. * Bitumen Primer is used to protect substrate against corrosive attack, is suggested to apply anti-corrosive primer.It is best for protection against sub-striate against atmospheric corrosion and chemical corrosion. It is a mixed substance made up of organic liquids that are highly sticky, water proof, viscous,acid proof as with all surface coating, good Bitumen Premier is used for long life of the system. it is applied by brush or roller and allowed to dry before any water proofing treatment so to avoid solvent it is used in defects such as cracks, broken mortar joints, etc. are to be repaired prior to Bitumen primer application. Product Details: Grade Standard Technical Grade Physical State - Liquid Usage - Industrial Color - Black Characteristics: Appearance/Color - Pasty liquid/ black Chemical Base - Bituminous rubber emulsion. Density - 1.0 kg/l Curing Speed/ Rate - 3 - 4 hours Tack free after - 5 - 10 hours Cured after - 2 - 4 days (Dependent on ambient Solid Content by - temperature, substrate temperature, Weight - relative Water Content by weight - humidity and thickness of the coating) Bitumen Content - 41% by weight - Thixotropic (The viscosity can be adjusted by - Viscosity adding up to max. 5% of clean water. - Stir well prior use) - For light protection: 1.0 mm min. Coating - For greater protection: ~ 1.5 - 2.0 mm Thickness applied - in two coats. Water Penetration - 48 h, 1 bar: 78.5 cm2: 0 ml under Hydrostatic - 96 h, 4 bar: 78.5 cm2: 33 ml Pressure - Water vapor 6 x 10-7 mg / hmPa Permeability Service - -30 C to 200 C Temperature - Adhesion Concrete - Very good, Timber: Very good, Metal: Moderate Glass: Poor