TL-101Tube rolling machine is used for compacting elements in order to increase the density of MgO. It has been well-received in France, Japan and other countries.
Functions:
1. The frame of this machine is made out of pig iron casting. The rocker die and tank are integral linear cutting. This machine is also equipped with fine-tuning dial, automatically removing sundries device and automatically cooling system.
2. According to the tube size and your special requirements, we have two types of motor of pinch roller for your choice. They are non-uniform speed (different speed) and uniform speed. The former make the tube better ductility, while the latter applies to the tube with large diameter.
3. When the tube specifications changed, we only need to replace a set of pinch rollers. The pinch rollers can be classified into two categories: high speed steel and tungsten carbide alloy .
4. Automatically stop when clogging.
5. This machine is of small size, low noise, convenient adjustments.
6. Applicable tube: Copper, iron, aluminum, stainless steel, etc.
Main technical parameters:
1. Tube diameter after compressing: 5.2mmí½19.0mm
2. The max. diameter before compressing: 21mm
3. The min. length of tube:110mm
4. Efficiency: 18m/min.
5. After compressing, the straightness can reach:1:300 , and the roundness can reach: 0 0.07 .
TL-110 Automatic coil winding machine is used to wind a wire into a circular heater. It applies to wire with different diameters, and both single-wire or double-wire are OK.
Functions:
1. The principal axis speed controlled by Japan Mitsubishi transducer. Continuously coils electric resistance and consistent clean-cut ends on the coils.
2. The machine will produce coils with very consistent resistance values and with open inside diameters for easy assembly to the terminal pins
3. When lack of wire or wire is broken, the machine would stop automatically. It also can accumulate the output automatically.
4. Wire with small diameter is usually cut by Galvan magnetism while wire with large diameter is cut by cylinder.
5. This machine is of small size, easy to operate, no operator is required.
6. Wire with large diameter can adopt double-pinch roller type.
Main technical parameters:
1 Power supply:220V,50Hz
2 Rated power:500W
3 Main axis speed:0í½2134rpm
4 Pinch roller speed:0½74rpm
TL-120 Semiautomatic tube cutting machine is used to cut copper, iron, stainless steel round tubes
Functions:
1. Pneumatic clamping, start cutting automatically.
2. Element rotates, automatically stop when loading finished.
3. Burr-free ends on the tubes, high efficiency, easy to operate.
Main technical parameters:
1. Power supply: Triphase 380V, 50Hz
2. Rated power: 0.8KW
3. Air supply: 5í½7kg/cm2
4. Efficiency: 8000pcsí½10000pcs/8h
5. Size LxWxH :800*500*900(mm)
6. Weight: 120kg
TL-340 Cartridge heater coiling machine is used to wind metal wire on the MgO rod.
1 Step motor drive, the pitch can be adjusted.
2 PLC control, easy operation.
3 Stable performance, high production.
4 Easy to change different specification.
Main technical parameters:
1. Power supply: Single phase AC220í+10% 50HZ
2. Power: 300W
3. Applicable diameter: í_ 21mm
4. Applicable length: 60í½800mm
5. Size: 1560*600*1220mm
TL-185 M-shaped tube bending machine, is an intelligent machine which can bend various shapes of tubes.
Functions:
1. 14 touch screen, operation instruction is attached.
2. PLC automatically controlled, change the parameters according to your requirement.
3. Servo motor controls bending and feeding, the speed, angle and length are all adjustable.
4. Pneumatic clamping, can bend 1½4pcs tubes at a time.
Main technical parameters:
1. Power supply: Single-phase 220V, 50Hz
2. Rated power: 4KW
3. Air supply: 5í½7kg/cm2
4. Applicable tube diameter: 6.0mmí½ª¦10mm
5. Size LxWxH:1650*900*1450 (mm)
6. Weight: 1000kg
