The CC1101RGPR is a low-power Sub-1GHz RF Transceiver designed for very low-power wireless applications. The circuit is mainly intended for the ISM (Industrial, Scientific and Medical) and SRD (Short Range Device) frequency bands at 315, 433, 868 and 915MHz, but can easily be programmed for operation at other frequencies in the 300 to 348MHz, 387 to 464MHz and 779 to 928MHz bands. The RF transceiver is integrated with a highly configurable baseband modem. The modem supports various modulation formats and has a configurable data rate up to 600kbps. CC1101RGPR provides extensive hardware support for packet handling, data buffering, burst transmissions, clear channel assessment, link quality indication and wake-on-radio. The main operating parameters and the 64byte transmit receive FIFOs of CC1101RGPR can be controlled via an SPI interface. In a typical system, the transceiver will be used together with a microcontroller and a few additional passive components.
NLAS4599DFT2G Overview
Packed in 6-TSSOP, SC-88, SOT-363, the electronic component is convenient for shipping overseas. This packaging method provides high reliability because it uses advanced packaging techniques. This analog switch is mounted in Surface Mount. 2:1 is the ratio of multiplexer to demultiplexer circuits. Operating temperature around -55C 125 C TA extended. There are 6 terminations totally. The electronic part delivers high-quality output through its 1 channels. If the voltage supply is 4.5V volts, the electrical component should be turned on and run. A total of 6 pins are injected into the electrical part body. The analog switch ics are built using SPDT switching circuits. Use NLAS4599 to search for variants of the digital switches. A 30Ohm internal resistance characterizes this multiplexer. Please refer to the datasheets for 6 pins functions. Multiplexer or Switches is a typical switch device. Users should never supply a voltage higher than 5.5V to a switch device. Analogue multiplexers of the Single supply type that are cost-effective. The lowest voltage the electronic part should receive is 2V. An operating current of 1 A would be sufficient for this switch device. An analogue multiplexer drains from a single voltage supply at 2V~5.5V. There are various bandwidths available for data transfer. An output of 2 is provided by the digital multiplexer.
NLAS4599DFT2G Features
1 Channels
Switch Circuit: SPDT
1A Supply Current
-3db Bandwidth: 220MHz
Bandwidth: 200MHz
NLAS4599DFT2G Applications
There are a lot of ON Semiconductor NLAS4599DFT2G Analog Switches & Multiplexers ICs applications.
Voice over IP/DSL Integrated Access Devices, Smart
Cable Modem, Cable PC
T1/E1 Terminals
Precision data acquisition
Compatible with 65 V DACs and ADCs such as
Channelized and Unchannelized DS3 applications
AD7840/8, AD7870/1/2/4/5/6/8
DVD-R
Isolation
Battery-powered systems
ADG779BKSZ-Overview
Packed in 6-TSSOP, SC-88, SOT-363, the electronic component is convenient for shipping overseas. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. In Surface Mount, this analog switch is mounted. 2:1 is the ratio between multiplexers and demultiplexers. An extended operating temperature of degrees Celsius. There are 6 terminations totally. This electronic part offers high-quality output due to its 1 channels. When the electronic component is given a voltage of 3V, it should be turned on and run. It is part of the design of the 6 series that this electronic component is included. The analog switch ics are built using SPDT switching circuits. Look for analog switch ic variants by searching with ADG779. There is 5Ohm internal resistance in this digital multiplexer. You can find the functions of the 6 pins in the datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. In normalcircumstances, users should not exceed 5.5V volts for the multiplexer. Single supply type digital switch with a low cost. It is recommended to use 1.8V as the lowest voltage for the electrical part. 1nA current would be enough for this multiplexer to operate. This analogue multiplexer requires a voltage of 1.8V~5.5V when it drains from a single voltage supply. The analogue multiplexer may be damaged if voltage is greater than 1 A. The 1 inputs need to be operated in order to work. In 200MHz-bandwidths, data can be transferred. The Drain to Source resistance of this electronic component is 5Ohm. A analog switch ics with 2 outputs is included.
