Hydraulic shaftless mill roll stand
Spindle 240mm, hyperbolic heavy rocker, expand chuck, multi-point brake, hydraulic drive lifting, panning left and right on the middle.
Hydraulic mill roll stand Specification
The symmetrical structure can install two rolls of paper at the same time and continually change paper, paper roller clamp, lift-lower, loosen, movement, contraposition, translation etc.
Equipment was made of HT200-wide casting.
Maximum loading of one side arm 1500-2000kg
Each stand with two set track and trolley for carry paper.
Pneumatic braking
Electrical components are controlled centralized(domestic brank)
One set main motor power of hydraulic mill roll stand is 2kw, each arm power 1.5*4kw
YIKE GROUP Hydraulic mill roll stand Advantage
Hydraulic mill roll stand characteristic
Professional manufacturer
Economic cost
Durable working
Fast delivery
Good after service
Structural features
1.Adopt hydraulic drive to complete the paper clamping, loosen, remove for the medium, translation left and right and othersï¼?the lifting of the paper adopts hydraulic drive.
2.Brake adjustable adopts multipoint braking system.
3.Each paper rack is equipped with two paper carts that can be served simultaneously from both sides.
IIã??Technical parameter
1ã??Paper clip range maximum : 1800mm minimum : 1000mm
2 Folder diameter maximum : 1500mm minimum : 350mm
3 Main shaft diameter of paper holder 240mm
4 Gas source work pressure Mpa 0.4---0.8Mpa
III Hydraulic system parameters
1 Work pressure Mpa :16---18Mpa
2 Lifting hydraulic cylinder 10 440mm
3 Clamping hydraulic cylinder 63 1300m
4 Hydraulic station motor power 3KW --380V -- 50Hz
Solenoid valve voltage 220V 50 Hz
Features
5-layer woven fabric
Composition of cotton, synthetic and IFDY
High moisture absorption and release; Low noise and high speed
Woven structure, anti-skidding
Introduction
Corrugator belt also named Corrugated board conveyor belt.
Corrugator belt is for corrugated board production line and developed specifically for Double Facer. Corrugator belts consistently keep the fastest absorption & release of moisture, which secures high quality cardboards with less consumption of heat and energy, and higher speed is assured. Corrugator belt have been specially developed for the transport of board and optimization of the drying process ,they resist the stress continuously and achieve as long a life as possible.
Type
Normal High speed corrugator belt & High speed corrugator belt with Kevlar edge
YK-K --- Reinforced Edges Kevlar armored on both edges
-----------------------------------------------------------
Width: 1400-3200mm
Speed: 100-300m/min
Kevlar edge: 100-200mm
Suitable for: Top and Bottom Belt
Change cardboards width frequently , or hotter plates.
Features
5-layer woven fabric
Composition of cotton, synthetic and IFDY
High moisture absorption and release; Low noise and high speed
Woven structure, anti-skidding
Introduction
The corrugator belt also named the Corrugated board conveyor belt.
Corrugator belt is for corrugated board production line and developed specifically for Double Facer. Corrugator belts consistently keep the fastest absorption & release of moisture, which secures high-quality cardboards with less consumption of heat and energy, and higher speed is assured. Corrugator belt have been specially developed for the transport of board and optimization of the drying process,they resist the stress continuously and achieve as long a life as possible.
Type
Normal High-speed corrugator belt & High-speed corrugator belt with Kevlar edge
YK-K --- Reinforced Edges Kevlar armored on both edges
-----------------------------------------------------------
Width: 1400-3200mm
Speed: 100-300m/min
Kevlar edge: 100-200mm
Suitable for: Top and Bottom Belt
Change cardboards width frequently, or hotter plates.
Main Technical Parameters And Requirements In Production Line
Electronic control system: fingerless single facer driving part NC thin blade slitter scorer double facer glue machine all adopt frequency motor delta frequency control system.operation interface easy and convenient Speed display control cabinet with each unit speed display, the unit call, emergency stop function.The main relays Schneider brand.
YV5B HYDRAULIC MILL ROLL STAND
technical parameters:
1. the range of clamping paper:MAX2200mm MIN1000mm
2.clamping diameters:MAX�¢1500mm MIN�¢350mm
3.main shaft diameter of paper holder:�¢240mm
4.gas source work pressure(Mpa):0.4---0.8Mpa
5.equipment size:Lmx4.3*Wmx1.8*Hmx1.6
6.single weight:MAX4000Kg
Hydraulic system parameters:
1.Work pressure(Mpa):16---18Mpa
2.lifting hydraulic cylinder:�¢100�?440mm
3.Clamping hydraulic cylinder:�¢63�?1300m
4.hydraulic station motor power:3KW --380V -- 50Hz
5.solenoid valve voltage:220V 50 Hz
SF-280S Fingerless Type Single Facer
Structural Features:
Adopt vacuum suction structure, with high-pressure strong blower.Suction with silencer.Gas supply and electrical control cabinet to focus on the same operation cabinet, not less than 1.5 meters away from the host Fully enclosed full operation side
Base and wallboard cast iron wall,Wallboard thickness130mm universal Joints.
Does corrugated roller material adopt 48CrMoalloy steel quenched. Laser hardening. Surface finish, main roll of corrugated diameter 280mm, surface hardness HRC60degree above.The key parts of the tile and pressure roller bearings Wafangdian produce high temperature bearings.
Pressure roller 284mm,surface grinding and chrome-plated cylinder control and remove up and down, 45 carbon steel materials, quenching (with cushioning devices).
Regular Technical Parameters:
Effective width: 1800mm
Operation direction: left or right determined in accordance with customer plant
Design speed: 100m/min
Temperature range: 200 260
Corrugated flute: UV type or UVV type
Roller Diameters Parameters:
Diameter of corrugated roller 280mm
Diameter of pressure roller 284mm
Diameter of glue roller 216mm
Diameter of preheat roller  320mm
Structural Feature
Main corrugated roller: 360mm according to the flute shape different pressure roller 415mm preheat roller  400mm.
Adopt negative pressure design, use less heat,make the core paper can be pressed evenly and attached to the surface of the corrugated roller, make the corrugator shape better.Because the pressure is evenly,the top of the corrugator can be glued more evenly,make the single corrugated paper bond better.
Corrugated roller use 48Crmo alloy steel, though heat treatment, surface through grinding make tungsten carbide treatment.
Corrugated roller and pressure roller use high stability gasbag control system, also have air pressure control buffering function.
Glue quantity control use electric adjust, glue isolation device electric, glue system can operate independently when main machine stop, to avoid glue use up.Glue tank is made of stainless steel.
Movable type glue system, wash easily, maintenance and repair is more easy.
Simple control system and touch screen system, with colorful pictures show the operate sate function choice faliure indication exclude and parameter setting all can act out the machine multi function, easy operation and humanization.
Preset device inside with spray system, adjust the core papers temperature and moisture.
Main,vice corrugated roller and pressure roller bearing all use high temperature grease, to make sure the bearing working life longer and running smoothly.
Introduction:
YK-1600SFL Single Facer Line is also called 2-layer corrugated paperboard production line. This Single facer Line is composed of Paper Roll stand, Single facer machine, paper cutting machine. To use the web paper material single face machine production line, producing and cutting single face corrugated paper as required sizes, it forms the corrugated board with no need drying. This unit has the advantages of reasonable fabric, advanced technology, high quality of production, high efficiency, low workmanship, operation and maintenance easy. This is the preferred equipment for the production of corrugated cardboard of the cardboard factories.
Specification:
Working Width
YK-1400SFL
1400mm
YK-1600SFL
1600mm
YK-1800SFL
1800mm
Heating method Electrical heating/Oil heating / Steam heating
Design speed 100-120m/min
Economical speed 80-100 m/min
Compress-air pressure 0.4-0.9MPa
Flute type Standard flute UV Flute
single facer line Standard spec. A,B,C,E,F
For other type and model, we can produce as customerâ??s requirement.
hydraulic shaftless mill roll stand
structural feature
Adopt hydraulic drive to complete the paper clamping, loosen, remove for the medium, translation left and right and othersï¼?the lifting of the paper adopts hydraulic drive.
Brake adjustable adopts multipoint braking system.
Every stand matched two sets paper car , and they can paper on the both sides at the same time.
Technical parameters
1 the range of clamping paper MAX1600mm MIN1000mm 2 clamping diameters MAX1500mm MINÂ 350mm
3 main shaft diameter of paper holder 242mm
4 gas source work pressure Mpa 0.4---0.8Mpa
