Vga / uxga splitter
Creative pcda 1004 is one input vga / uxga distribution amplifiers which is very rigid for driving signal. This amplifies and distributes the signal from any pc or work stations to four separate display devices. With 350 mhz of video bandwidth, the pcda 1004 is capable of driving any vga v uxga computer signal up to 100mtrs. (using standard vga cable). Each outputs are amplified to maintain the original signal quality. Pcda 1004 eliminate interference and noise caused by poor signal quality or long cable run. The pcda 1004 is compatible with lcd monitors, crt, lcd and dlp projectors and high end crt monitors. This is also compatible to video walls; led walls.
Video inputs, Discriptions
Number/signal type : 1 vga-uxga
Connectors : 15-pin hd female
Impedance : 75 ohms
Hor. Fr. ,: 15khz to 130 khz
Vert. Fr. ,: 60 to 150 hz.
Video out puts,
Number of signal 4# : vga-uxga
Rgbhv, rgbs, rgsb, rsgsbs
Connectors : 15-pin hd female
Impedance : 75 ohms
Sync
Input type : , Rgbhv, rgbs, rgsb, rsgsbs
Output type : , Rgbhv, rgbs, rgsb, rsgsbs
VGA interface
C reative vi 1002 is a analog computer-video interface with a female 15-pin hd input connector and a 15-pin hd buffered local monitor output. The vi 1002 has a 15-150 khz scanning range, 350 mhz rgb video bandwidth, and is compatible with nearly every computer / work stations and video signal type, including vga v uxga. The vi 1002 also features auto id bit selection , ensuring that computers requiring local monitors to operate will do so in the event that one is not attached. For pcs, the vi 1002 connectivity is on 15-pin hd male to male cable.
Video in put ,Discription
Number/signal type ,1 analog rgbhv, rgbs, rgsb
Connectors 1 : 15-pin hd female
Nominal gain level :,.7v pp for rgb
Impedance : ,75 ohms
Hor. Fr. : ,15 khz to 130 khz
Vert. Fr. : ,30 hz to 170 hz
Video o/ put,
Number & type of signal :1 analog rgbhv, rgbs,
Rgsb
Connectors : 5 bnc female, 1- 15-pin hd female
(buffered local monitor)
Dual function screen interface
Ideal to control motorized projection screen / projector lift / drapes and rack (ac 220 v operated).
Provision for operating 24v drapes motor.
Timmer controled action : cut off supply to screen / lift and drapes automatically after 2 minutes.
Can be used to (on÷ (off÷ complete rack in which equipments are installed.
Can be used to control movement of screen / lift and drapes manually (without touch panel) with three individual switch provided on front panel.
Blinking led provided on front panel to show the active function
Inputs:
For screen: individual 2 pin captive screw terminals for up & dn movement
For lift: individual 2 pin captive screw terminals for up & dn movement
For drapes :individual 2 pin captive screw terminals for up & dn movement
For rack : one 3 pin captive screw terminal for
G n p connections
Out put:
For screen : three pin captive screw terminals
For lift : three pin captive screw terminals
Projection screen interface
ideal to control motorised projection screen (ac 220 v operated ).
timmer controled : automatically gets off after 1.5 minutes (only for screen)
can control set of tube lights (which are programmed in different zones). Saving cost of additional light control unit.
can control any electronic / electrical gadgets / equipments which is 220v ac operated.
can be used to switch (on÷ (off÷ audio video equipments installed in rack.
Maximum load upto 1 kva
Ac 220v / 50hz operated
One motorised 220vac screen
Three separate port for three different audio video sources
