Product name: DT Desulfurization Pump
Model: DT Desulfurization Pump
Application: Can be used as the limestone slurry pump, gypsum discharge pump, filter liquid feeding pump, an absorption tower circulating pump, recycling pump etc.
Product overview
DT (TL) type desulphurization pump (industrial slag slurry pump), referred to as: DT (TL) desulfurization pump, is a successful design experience based manufacturing in ZJ series slurry pump, in view of our country industrial flue gas desulfurization pump characteristics, absorbing domestic and foreign advanced technology products, a new generation of series desulfurization pumps carefully the development of the. Can be used as the limestone slurry pump, gypsum discharge pump, filter liquid feeding pump, an absorption tower circulating pump, recycling pump etc.
DT Desulfurization Pump
Product name: Gravel Pump01
Model: SG (or GH) Type Gravel Pump
Application:
Product overview
SG (or GH) type gravel pump is mainly used for the continuous conveying granular too big material strong abrasive slurry pump can transport the general. Suitable for dredger dredging, dredging, mining and metal smelting blast slag conveying etc.. The GH type gravel pump for high lift.
The pump adopts a single shell pump structure connected to the cassette, the flow passage spacious. The over-current components using Ni - hard, high chromium wear-resistant materials. Pump outlet direction can be in any one of 360 degrees, with convenient installation and use, the cavitation performance, has the advantages of anti abrasion etc.
Gravel Pump01
Product name: PN Mud Pump
Model: PN Mud Pump
Application: can be used for transporting solid-liquid two-phase fluid with mine
Product overview
Mud pump is a Horizontal single-stage single suction cantilever centrifugal slurry pump, can be used for transporting solid-liquid two-phase fluid with mine. Can also be used in building materials, paper, food, feed and other departments to transport all kinds of slurry. The maximum transmission, concentration of 50-60% (weight)
Flow manufacturing using wear-resistant alloy material PN type slurry pump, long life. 6 "and 6" mud sand below the impeller and the shaft is connected with the screw, 8 "and 8" above the mud pump used in key connection. The gap between the blade and sheath and the impeller can be adjusted, to maintain efficient work. 8 "and 8" above the mud pump, the pump body is large, using open structure form level, the disassembly and the maintenance are convenient.
Shaft seal packing seal used in general, work to win into higher than operating pressure of 1 kg / square cm shaft seal water.
Model PN mud pump, according to the transmission direction, rotates in counterclockwise direction (including 1, 2, 3PN clockwise) Ye Lun with a screw connected with the shaft, if the rotating in opposite directions, Ye Lun will fall off from the shaft, causing the accident.
PN Mud Pump
Product name: Flue Gas Desulfurization Pump
Model: Flue Gas Desulfurization Pump
Application: FGD pumps are sailed Pump Company in LC-T series slurry pump, the successful design manufactured on the basis of experience, in view of industrial flue gas
Product overview
Flue gas desulfurization pump Overview:
FGD pumps are sailed Pump Company in LC-T series slurry pump, the successful design manufactured on the basis of experience, in view of industrial flue gas desulfurization pump characteristics, absorb with similar products within and outside the advanced technology, well-developed The new generation of series desulfurization pumps. Dedicated to the absorption tower circulating pump PH: 2.5 to 13 chlorine ion concentration: ¹60000ppm weight concentration:¹60% Medium temperature: ¹100C.
Absorber circulation pump is large FGD key equipment, means there is high demand for its reliability and service life. FGD means more than half of the power consumed for driving the absorber circulation pump. Therefore, the circulating pump should have a high efficiency. Hydraulic design of the pump design and selection of materials flow components directly related to the efficiency of the pump operation, reliability and service life.
We developed the absorber circulation pump, pump, pump cover over-current parts are made of 2605N material, impeller, wear plate is used Cr30A material.
Hydraulic design of the pump, drawing the French company J S phase flow pump design and manufacturing technology, and the use of modern CAD, CFD technical correction.
Second, the flue gas desulfurization pumps structural features:
(1) The pump is single-stage single-suction centrifugal pumps, which form in practice has proved to be particularly suitable for FGD absorber circulation pumping device abrasive, corrosive slurry.
(2) The impeller, wear plate without using mouth ring seal in the form, set the port ring will be slurry rapid wear, leading to the rapid decline in the efficiency of the pump.
(3) having an axial adjustment structure, the impeller can be easily adjusted to maintain an axial gap between the impeller and the wear plate and the front cover, so as to maintain the high efficiency of the pump. It is always easiest to maintain and the most effective and efficient way to pump operation.
(4) is arranged in the form of pump is "pull" structure. This allows the pump impeller during disassembly, mechanical seals and shaft assembly without removing the inlet and outlet pipes.
(5) bearing with thin oil lubrication. Bearing mounted on a rubber ring secondary seal removable bearing box, to prevent dirt and water from entering.
(6) The shaft is a large diameter, short axis head can reduce shaft deflection at work, thus extending seal life.
Third, the flue gas desulfurization pump design advantages:
Overview: back pull-out design of the entire rotor assembly can be pulled from the motor, easy to maintain, the pump can remain in the pipeline, without removing the motor.
1. Front pull-out design wear plates, impellers, mechanical seal can be disassembled inlet end
2. bearing bracket can be adjusted to improve the wear resistance
3. The bearing lubrication oil immersion
4. Pump: pump pressure and wear of sufficient size, materials used 2605N, weldable, volute tongue wear some special treatment, tangential flow channel outlet, the body set foot supporting way.
5. Wear plates: the part is mounted between the pump and imported materials Cr30A, this material has excellent resistance to abrasion and erosion resistance, overall performance, thereby extending the life of the pump and impeller.
6. Impeller: material Cr30A, not welded, taking into account the long run is more economical, since the bearing holder can be adjusted when the situation abrasive wheel, the wheel can be re-processed and prolong life. Front blade structure prevents large particles rushed impeller and wear plate gap, the leading blade and wear plate gap, reducing the media (in impeller and wear plate) flow rate, reducing wear, special blades wear process design, back blade design, reduced axial force, but also to block large particles, high pressure bearing design (simulation without axial force hydraulic model back under the blade), the
7. impeller vent design, can be discharged within the gaseous medium, to prevent dry running mechanical seals.
8. After the pump cover: materials used 2605N, weldable, wear usually occurs in the back of the blade area, the pump head is mounted on the bearing bracket, release stress and allow greater wear and prolong the service life of the pump cover bolts fixed bearing frame for easy disassembly without the card and damage to the pump when dismantling the mechanical seal.
9. A bearing body: the bearing body consists of two parts, the carrier and the bearing housing, the bearing housing and the adjusting screw can be adjusted by means of bolts, move horizontally within the carriage. This has the advantage: in the bearing housing to move the carriage (reprocessing size according impeller), but the inner and outer bearing ring without relative displacement, since no relative displacement, seals fully functional. When removing the lower part of the reservation on the base for easy removal, position accuracy, the installation will not occur mutual jamming of parts.
10. Mechanical seal: The mechanical seal is designed to Single seal cartridge structure, easy disassembly. Wash design there are two options: one, loaded wash water pipe fixed wash water; of the two, without a fixed wash water line, segmental wash. In the mechanical seal the work area, if the medium containing gas, mechanical seals would run dry, so the impeller is designed with vents, you can avoid large, dirty particle contact mechanical seal. Easy emptying drainage pump seal cavity volume, full lubrication, cooling sufficiently.
Flue Gas Desulfurization Pump
Product name: Gravel Pump02
Model: SG (or GH) Type Gravel Pump
Application: used for the continuous conveying granular too big material strong abrasive slurry pump can transport the general
Product overview
SG (or GH) type gravel pump is mainly used for the continuous conveying granular too big material strong abrasive slurry pump can transport the general. Suitable for dredger dredging, dredging, mining and metal smelting blast slag conveying etc.. The GH type gravel pump for high lift.
The pump adopts a single shell pump structure connected to the cassette, the flow passage spacious. The over-current components using Ni - hard, high chromium wear-resistant materials. Pump outlet direction can be in any one of 360 degrees, with convenient installation and use, the cavitation performance, has the advantages of anti abrasion etc.
Gravel Pump02
