(main technical parameters and scope of supply)
1 the oil cylinder: inside 280mm, the rod 185mm the effective trip: 4m, 2 bars
The maximum thrust of the 2 cylinders: 260 tons;
The forward speed: 0100cm/min,
The max backward speed: 380cm/min.
2 The pump station
63scy-plunger pump :1 set, 18.5kw motor: 1set (the main working pump)
25scy-plunger pump :1 set, 11kw motor: 1set (the main working pump)
Cb-63 gear pump: 1 set, 7.5kw motor: 1set (for fast forward and back)
Cb-16 gear pump: 1 set, 4kw motor: 1set (for lifting the valve)
3 The frame for the main engine: 25# channel steel, welded with 24kg steel rail
(to know more about it, send your requirement).
Max od.325mm x 20mm
(main technical parameters and scope of supply)
1 oil cylinder: inner diameter: 125mm, stem diameter:90mm, the trip: 3m, pressure: 21mpa, 2 bars
Maximum thrust of the 2 cylinder:50tons ;
The forward speed: 0��140cm/min , the fastest back speed: 450cm/min.
2 Pump station25scy-plunger pump :1 set
5.5kw motor:1set(the main working pump)
Cb - 20 gear pump: 1 set, 3kw-motor 1set
We select the hydraulic valve with panel integrated hydraulic system.(total power:8.5kw, voltage:380v, 220v-50hz)
3 Intermediate frequency electric ark (power:160kw)
4 scope of supply:
A. Main engine(oil cylinder, frame for the main engine): 1 part, hydraulic pump station: 1 set, distribution box 1set
B. M-frequency electric ark1 set,
Water cable 2 (l = 2.5m),
127 heated induction coils1 piece.
No packing for the main machine
Hydraulic pipe bending machine
(main technicial parameters)
the main oil cylinder:the inter-diameter200mm, stem diameter160mm
Trip:4m (2 bars)
hydraulic pump
1.Pump station selection:
10scy plunger pump 1set; electric motor 5.5kw 1 set (the main pump station , frequency conversion and speed adjustable)
Cb-63 gear pump 1 set, electric motor 11kw 1set (can be force and back with a high speed)
Cbt-20 gear pump 1 set, electric motor 7.5kw 1 set(usd for the oriented pichwheel, fixture motor)
2.Hydraulic motor: 5 pieces
3.Hydraulic control valves: 1 set
4.Oil box:1 piece
5.Manipulate switch box:1 set
heating systerm:m-frequency electric ark, 1set, 500kw
assembly parts:
1.Fixtures and clamping round adopt 45# casting steel
2.The body of the main engine, structural welding section, the main bord of the pushing plate are used with the welding parts.
3.The silk column, chain, the standard parts, the bearings are all national standard parts.
(we woud design a pipe bending machine unique for you).
No packing for the main machine
101618mm hydraulic pushing
Pipe bending machine
master cylinder
Inside diameter: 280mm outside diameter: 325mm
Effective strock:12m the max thrust of the 2 cylinders260t
The other small cylinder125mm -1 piece
2 hydraulic pump station
Astation configuration:
25scy plunger pump 1 set 7.5kw motor 1 set ( to converse frequency adjust the speed of the master pump)
Cb-100 gear pump 1 set 15kw motor 1 set ( fast forwad and backward)
40scy plunger pump 1 set 11kw motor 1 set (used to guide clamp wheelfixture motor).
Bhydraulic motor 5 set
Chydraulic controlling valve 1 set
Doil tank 1 piece
Econtrol consolepower distribution box 1 sets
3medium frequency power supply
Amedium-frequency electric cabinet 1 set 600kw
Bcapacitor cabinet 1 piece
Creactor 1 piece
Dwater cooled cable 2 pieces x 3m
Equenching transformer 1 set 3000kva
F1016-426 water cooled heating coil 6 pieces
4assembly parts
Aclamp wheelfixture made of 45# cast steel
Bmaster fuselageweldmentthe main pushing board are welded board
Cscrewchainstandard parts and bearing are national standards
Dthe guider is dovetail groove slide plate mode.
No packing for the main machine
12mm tee machine
The upside cylinder:inner diameter 650mm
The side-cylinder:inner diameter 600mm
B.The biggest equal-diameter carbon steel tee can be made: 8 mm
C.The diameter under a wall thickness 8mm can be changed
D.The tee with a wall thickness between 10mm and 12mm can be made by 3 times��squeezing.
A.Factory price with whole structure, the main frame weights about 28tons
B.Factory price with separated structure , the main frame weights about 45tons
��a.The upside cylinder:inner diameter 800mm
The side-cylinder:inner diameter 750mm
B.The biggest equal-diameter carbon steel tee can be made: 12 mm
C.The tee with a wall thickness 12mm, if you want to change its diameter, you need squeeze 2-3 times.
No packing
