Supplier: Solvent, tdm( tertiary dodecyl mercaptan)
Supplier: Chemical, chemical raw material, auxiliaries, solvents, paint, textile fiber, rubber, plastic, paint drier, plasticizer, flame retardant, surfactant, additives, steel pipe, steel tube, stainless steel tube, stainless steel pipe, ms pipe, pipe fitting, flange, fasteners, steel wire
Services: Transportation agent,customs clearance service,
Buyer: Import chemical raw materials, auxiliaries, bulk commodities
[Technical Indicators] 1. Industrial grade Indicator Name/Indicator Value Powdered Products (F) Needle Products (Z) Level 92 Level 93 Level 95 Level 92 Level 95 Appearance White or light yellow powder, without caking White or yellowish needle-like, without lumps Active matter,% 92.0 93.0 95.0 92.0 95.0 Free oil,% 1.2 1.2 1.2 2.0 1.5 Inorganic salt,% Sodium sulfate 5.8 4.8 2.5 4.8 2.5 Sodium chloride 0.15 0.15 0.15 0.15 0.15 Moisture,% 2.0 2.0 2.0 4.0 3.0 PH value (1% aqueous solution) 7.5-9.5 7.5-10 Whiteness (WB), 90 2. Toothpaste grade Indicator Name/Indicator Value Toothpaste Grade (Y) (I) Level (II) Level (III) Level Appearance White or yellowish powdery or needle-like, without caking Active matter,% 95.0 93.0 93.0 Free oil,% 1.2 1.2 1.2 Inorganic salt,% Sodium sulfate 2.5 3.2 4.0 Sodium chloride 0.15 0.15 0.15 Moisture,% 2.0 2.0 3.0 PH value (1% aqueous solution) 8-9.3 8-9.3 8-10 Whiteness (WB), 90 Foaming capacity/mm 180 Heavy metal (as Pb)/ (mg/Kg), 15 Arsenic content (as As)/ (mg/Kg), 3 Total bacterial count/ (CFU/G), 100 Total number of molds and yeasts/ (CFU/G), 100 Fecal coliforms/G Not to be detected Pseudomonas aeruginosa/G Not to be detected Staphylococcus aureus/G Not to be detected  3. Latex grade Indicator Name/Indicator Value Latex grade (powder, needle, liquid) Aggregate grade Seed level Liquid K12 Appearance White or yellowish powdery or needle-like, without caking Light yellow transparent liquid Active matter,% 94.0 92 28.5-30.5 Free oil,% 0.8-1.0 1.5-2.0 1.5 Inorganic salt,% Sodium sulfate 3.0 3.0 1.5 Sodium chloride 0.15 0.15 0.05 Moisture,% 3.5 3.5 - PH value (1% aqueous solution) 8-10 7.5-9.5 Whiteness (WB), 90 - Color Klett (30% active), - 60 4. Reagent grade Indicator Name/Indicator Value Reagent grade Level 99% Level 97% Appearance White flaky crystals White powder Solubility (1%, alcohol) Completely dissolved Solubility (10%, aqueous solution) Completely dissolved Chroma APHA (20%, deionized water), 15  - Active matter (%), â?¥ 99 (on dry basis) 97 Petroleum ether soluble matter (%), 0.2 1.0 Sodium sulfate (%), 0.5 1.5 Sodium chloride (%), Moisture (%), 1.0 2.0 PH value (1% aqueous solution) 6.0-8.0 6.0-11 Phosphate, 1ppm - Lead (Pb), 2ppm Iron (Fe), 1ppm Nitrogen, 5ppm - Arsenic (As), 0.1ppm Fraction content (%), 99.0 Absorbance (3%, deionized water) 230nm 0.4 260nm 0.1 280nm 0.1 - 410nm 0.01
Supplier: Chemical solvents like acetone, ethanol, ipa,mix xylene, mix toluene etc ( recycled, off grade, stock, contaminated, expired products
Services: :
Buyer: Off spec solvents and glycols for reprocessing. unused, off spec, expired,stock, bottom sludge, slurry products like ea, ba, ipa, mix xylene, hydrocarbons etc
Commodity: Synthetic Cryolite Formula: Na3AlF6 M.W.: 209.95 Properties: The product is a white crystalline powder or a sandy-size granularity, and a pinkish crystalline powder or a sandy-size granularity as well. Sp.gr.2.953.01g/cm3, melting point about 1000centigrade, specific heat 1.056j/gcentigradeat 18100centigrade. Its slightly soluble in water, but insoluble in anhydrous hydrogen fluoride. The content of its crystal water will be decreased while the increasing of the molecular ratio, therefore its loss on ignition will be also decreased while the increasing of the molecular ratio. After the paste of synthetic cryolite with different molecular ratio dehydrates, the loss on ignition at 800centigrade will appear 10.34%, 6.22% and 2.56% when the molecular ratio reaches 1.74, 2.14 and 2.63 reactively. Specifications: Appearance white powder F 52% min Al 12% min Na 33% max SiO2 0.36% max Fe2O3 0.08% max CaO 0.5% max P2O5 0.03% max SO4 0.6% max H2O 0.4% max Loss on ignition 2 % max Uses: Its mainly used as a flux in the aluminum smelting by fused-salt electrolysis; also an opalizer in the manufacture of enamel; an opacifier and auxiliary solvent of glass and enamel; an insecticide of crops; a flux in aluminum alloy casting; and in the production of ferrous alloy and effervescing steel; as well as a wear-resistant filler for resin and rubber-boned abrasive wheels. Packing & Storage: In plastic coating woven bags with plastic film inside, 25kg,40kgs, 50kgs or 1000kgs net each, or as the requirement of clients.Stored: in a cool , ventilated, dry place.