Scrap Trading Incorporation

SPECIFICATIONS: the following Percentage Points: Chemical Composition Carbon - 0.54 to 0.82% Phosphorus - 0.035% max Manganese - 0.60 to 1.05% As. - 0,01max of Mass share Silicone - 0.18 to 0.40% Sulphur - 0.035% max Norms - R-50 GOST-7173-75 / R-65 GOST- 8165-75 The scrap consists of R-50 (51,67 KG/m) R-65 (64,72KG/m) Used Rails shall be considered free of alloys when the residual alloying elements do not exceed Cut to 1.5 meter length (standard) 1. Technical terms: USED RAIL R50-R65 2. Specifications and Chemical Composition: Used Rail: R50 (51.67KG/Meter, GOST 7173-55), Used Rail: R65 (64.72KG/Meter, GOST 8161-75). Size & Weight: Length: 12meter ~ 12.5meter Maximum or less according tobuyerâ??s instruction; Expenses on seller Width: 5.5 inches ; Weight: 64.72Kg. No fishplates or steel pieces or bolts are attached to the used rails. All rails are clean and straight. No pitting. Only atmospheric rust No heavy rust. It is mandatory that Rails must be cut into length 1.5 meter(max.) before shipment.

We engage in metal materials, metal products, steel products, i.e. ferrosilicon, titanium iron, silicon ferrozirconium, ferrovanadium, ferrowolfranium, mg-ferrosilicon-rare-earth alloy, ferromolybdenum, ferrochromium products, ferromanganese products; non-ferrous metal products, i.e. stibium ingot, silicon-calcium, silicon manganese, zinc-alum alloy, zinc ingot, lead ingot, chrome powder, magnesium ingot, aluminium ingot/ coil/ can/ scrap, copper ingot/wire/ sheet/ scrap, Plastic and Polymer Scrap, Plastic Raw Material Granules, Rubber Scrap, Paper Scrap, etc. Chemical Composition: C:0.06 - 0.082% Mn:0.75 - 1.05% SI:0.13 - 0.28% P: Max 0.035% S: Max 0.045% Ar: Max 0.15% HMS 1 / 2 STEEL METAL SCRAP FOR SELL: Iron Scrap HMS1 & 2 C:0.06 - 0.082% Mn:0.75 - 1.05% SI:0.13 - 0.28% P: Max 0.035% S: Max 0.045% Ar: Max 0.15% HMS 1 / 2 STEEL METAL SCRAP FOR SELL: Iron Scrap HMS1 & 2 C:0.06 - 0.082% Mn:0.75 - 1.05% SI:0.13 - 0.28% P: Max 0.035% S: Max 0.045% Ar: Max 0.15%

C: 0.54-0.8% Si: 0.18-0.40% Mn: 0.60-1.05% S: 0.04% Max P: 0.035% Max Used rails R50-R65 Under 200-202 International Standard ISRI Code 27-29 R50 R65 Harmonization System (HS) Code : 730210

Heavy Melting Steel (HMS): Heavy melting steel is a designation for recyclable steel. It is categorised into two major categories: HMS 1 and HMS 2. The difference between the two is HMS 1 does not contain galvanized and cast iron, whereas HMS 2 does. Because both grades guarantee a minimum piece thickness â?? at least 1/4inch (6.3mm) for HMS 1, and 1/8 in for HMS 2 â?? consignments have a high density. The typical constituents are plates, truck parts, structural items, large machinery parts, automatic parts, pipes, post consumer steel goods. Quality Heavy metal ,Iron Scrap/ Metal scrap HMS 1 and HMS 2 scrap steel for sale

R50- R65 - IRSI CODES; The chemical composition is the standard for R-50 R-65 Tee rails original weigh 50 pounds per yard or heavier,6 meters long and over. Material to be suitable for rerolling into bars and shapes. Free from bent and twisted rails, frog, switch and guard rails, rails with split heads and broken flanges. Continuous welded rail may be included provided no weld is over 9 inches from end of the piece of rail. Free from Fluff, Nonferrous inclusions, excessive rust and other impurities. Free from war and explosives, shells, cartridges, other arms and ammunitions used or otherwise and any closed containers. Free from any radioactive materials, any harmful chemicals, substances, and coatings any organic waste any other harmful substances. Dirt, dust, rust fluff and other impurities not allowed over 05 %. The rails are to be neatly bundled and secured with iron wire or straps, provided with adequate lifting hooks. Individual bundles not to exceed 5 MTW. Used Rails R50 - R65 Chemical Composition Used Rails; C: 0, 54 - 0,82 Si: 0,18-0,40 Mn: 0, 60-1, 05 S: 0.04 max P: 0,035 max As.: 0, 01 max of Mass share Norms: R-50 GOST7173-75 and R-65 GOST-8165-75 The scrap consists of R-50 (51, 67 kg/m) R-65 (64,72 kg/m) Used Rail ISRI 27-29 ISRI-CODES; (27) Rail, Steel No. 1. Standard section tee rails, original weight 50 pounds per yard or heavier, 10 feet long and over. Suitable for re-rolling into bars and shapes. Free from bent and twisted rails, frog, switch, and guard rails, or rails with split heads and broken flanges. Continuous welded rail may be included provided no weld is over 9 inches from the end of the piece of rail. (28A) Rail, Steel No. 2 Cropped Rail Ends. Standard section, original weight of 50 pounds per yard and over, 18 inches long and under. (28B) Rail, Steel No. 2 Cropped Rail Ends. Standard section, original weight of 50 pounds per yard and over, 2 feet long and under. (28C) Rail, Steel No. 2 Cropped Rail En ds. Standard sec t ion, original weight 50 pounds per yard and over, 3 feet long and under. (29) Rail, St eel No. 3.Standard section tee, girder, and/or guard rails, to be free from frog and switch rails not cut apart, and contain no manganese, cast, welds, or attachments of any kind except angle bars. Free from concrete, dirty and foreign material of any kind. The rails can be cut to the length the buyer wants