Specifications 1.odorless 2.low VOC 3.antimicrobial 4. mildew resistant 5.environmentally friendly 6.waterproof 7.Scrub resistance Description It is an enhanced mildew proof product adopting nano-scale Ag+ antimicrobial and mildew proof technology, integrating odorless formula, with fresh product smell, smooth paint film, durable and beautiful paint.As an affordable and environmentally friendly product with excellent decorative performance, it is characterized by fresh smell, environmental health, strong covering power, large painting area, convenient constructionapplication, short constructionapplication period, etc. Specification Data Solvent: Water Pigment: Non-lead pigment Theoretical Solids By Volume: more than 50% Theoretical Coverage: Theoretically 1 litre of this product covers 12 sqm in 1 coat Coverage varies considerably depending on application methods and surface roughness and porosity. Shelf Life: Minimum 12 months at 77F(25C) unopened and store in cool and dry places. Recommended Film Thickness: Wet: 80 micron Dry: 30 micron Dry Time: At 77F (25C) and 50% R.H. to recoat Touch Dry: 1 hours Recoat : 2-3 hours Application: Brush, Roll, conventional spray or Airless Spray. Thinner: Thin up 15% depend on different application methods & temperature. Do not over thin by adding more than 30% water. Brush or Roller: For sealing new or bare surfaces thin with up to 1 part of clean water to 5-10 parts of paint(10%-20%) Conventional Spray: Add up to 1 part clean water to 5 parts paint(20%) Airless spray: do not thin Clean-up: Clean up equipment with water Typical painting system Substrate System All kinds of Wall surfaces 1.Alkali Resistance Primer (1 coat) 2.Emulsion Wall Paint (2 coats)
Supplier: Cast iron skulls, cast iron borings and turnings, steels skulls, eaf skulls, plate iron, mill scale, metal scrap, incinerated scrap (e46)
The Incinerated scrap or E46, is the by-product derived from the reprocessing of incinerated domestic waste. After the combustion process, the furnace output (IBA Incinerator bottom ash) is firstly washed, magnetically separated and screened to separate any no ferrous material. At a visual inspection, the material is fragmentized, with iron and steel parts, resulting partly cut or in shredded form. The stock appears heterogeneous and contains all kind of cut or dismantled steel parts such as sheets, bars, frames, wires, bolts and other iron/steel household residues. The incinerated scrap is eventually oxidized, due to the thermal and cooling treatments, that the material has been submitted to. The burnt scrap also contains minor slag parts, ash and iron oxide, due to the recovery process. Such components are inherent and adhere to the scrap surface. The total impurities, can be sorted, but not fully removed. The consignment does not contain any type of arms, ammunition, mines, shells, cartridges, radioactive contaminated, or any other explosive material in any form either used or otherwise. The collected stock, is stored in open air, on cemented flooring. It can be loaded loose in 20â?? heavy duty container. Please feel free to contact us for further details.
Pipe fittings are the general names of parts and components that play the role of connection, control, direction change, diversion, sealing and support in the pipeline system. Steel fittings are pressure fittings. According to the different processing technology, it is divided into four categories, namely, butt welding pipe fittings (divided into weld and no weld), socket welding and threaded pipe fittings, flange pipe fittings. According to the application: 1. pipe fittings for connecting pipes are: flanges, live joints, pipe hoops, clamps, clamps, throat hoops, etc. 2. changing the direction of the pipe: bends, bends. 3. pipe fittings changing pipe diameter: variable diameter (different diameter pipe), different diameter elbow, branch pipe table, reinforcing pipe. 4. pipe fittings with additional piping branches: three links, four links. 5. pipe fittings for pipe sealing: gasket, raw material belt, thread hemp, flange blind plate, pipe plug, blind plate, head, welding plug. 6. pipe fittings for pipe fixing: clasp, hook, ring, bracket, bracket, pipe clamp, etc. According to the connection :1, welded pipe fittings 2, threaded pipe fittings 3, clamping pipe fittings 4, clamping pipe fittings 5, socket pipe fittings 6, rubber ring connection pipe fittings According to the material divided into 1, cast steel pipe fittings 2, forged steel pipe fittings 3, alloy pipe fittings 4, stainless steel pipe fittings. Pipe fittings are widely used in municipal, petrochemical, west-to-east gas transmission, ships and nuclear power.
AINiCo is composed primarily of Aluminum Nickel Cobalt and also Copper and Titanium. They are manufactured through either casting or sintering process. Cast AINiCo may be manufactured in complex shapes such as horseshoes not possible with other magnet materials. Sintered AINiCo offer slightly lower magnetic properties but better mechanical characteristics. it can be efficiently magnetized in any direction, and for anisotropic AINiComagnet, it generally has greater magnetic capacitive in a preferred orientation than isotropic types. AINiCo is hard and brittle, Machining or drilling cannot therefore be accomplished by ordinary methods. Holes are usually cored in at the foundry, and magnets are cast close to final size and then finish machined to closer tolerances. â?¢ Advantages of AlNiCo Magnet: 1.Customized designs are available. 2.Max working temperature can be as high as 550�°C. 3.Disadvantage: Br and BH(max)are not as high as rare earth magnet. 4.High energies and relatively low coercivity. 5.High magnetic flux density; low mold charge stable temperature properties; easy to shap.
Fasteners are the general term of the class of mechanical parts used in fastening two or more parts (or components) into a whole. It is widely used in energy, electronics, electrical appliances, machinery, chemical, metallurgy, mold, hydraulic and other industries, at the same time, in various kinds of machinery, equipment, vehicles, ships, railway, bridge, construction, structure, tools, instruments, chemical, instruments and supplies, you can see all kinds of fasteners, is the most widely used mechanical foundation parts. It is characterized by a wide variety of variety specifications, different performance uses, and a very high degree of standardization, series, and generalization. Therefore, a class of fasteners that already have national standards is called standard fasteners, or simply standard ones.
Pularin: Foot ball shaped 60 atoms of carbon at edges is layed in pularin.Pularin atoms are arranged in ball. Each atom is called Bucky balls and tubes are called Bucky tubes or Nano tubes.Each nano tube is 1 to 7 nm diameter i.e 1nm=50000 part of a hair sting. where? 1)mangampet ,cuddapah dist.Ap,India.app 800 ppm(parts prer million)info given by stanford University. Cost: 150 times costlier than gold. 10 grams pularin $23000 to $45000 also info given by Bucky-USA website. Special uses if this becomes common: 1)Pularin coting on aeroplanes withstands from thunders ,rains ,Flashes etc. 2)Bullet proof ackets 3)curing cancer etc.
Steel products refer to solid straight steel products with a certain section shape and size, including wire, profile and plate, which are formed by plastic processing except pipes. It can be divided into hot rolling, cold bending, cold rolling, cold drawing, extrusion, forging, hot bending, welding and special rolling according to the production method. It can be divided into railway, shipbuilding, mining, structure and construction according to its use. According to the material can be divided into carbon steel, alloy steel and stainless steel. At the same time, these steel products can be reprocessed to form semi-finished products or finished products to meet special requirements. We can according to the customer's different needs, according to the drawings or samples for reprocessing production.
Neodymium magnets (also known as NdFeB, Neo or NIB magnets), are strong permanent magnets made from an alloy of neodymium, iron & boron. Part of the Rare-Earth magnet family, they have the highest magnetic properties of all permanent magnets. Due to their high magnetic strength and relatively low-cost, they are the preferred choice for many consumers, commercial, industrial and technical applications.NdFeB is divided into sintered NdFeB and bonded NdFeB. Bonded NdFeB is magnetic in all directions and corrosion resistance and is divided into Bonded Compression NdFeB Magnet and Bonded Injection NdFeB Magnet; while sintered NdFeB is easy to corrosion, the surface requires coating, generally divided into axial and radial magnetic charging. Advantages of Sintered NdFeB Magnet : 1. Very hard and brittle, high diamagnetic resistance, high cost / performance ratio, not suitable for high working temper ature; 2. Magnetic performance is higher than that of the rare earth cobalt permanent magnet, the residual magnetic induction strength, magnetic induction coercivity, the maximum magnetic energy product is very high, is the current magnetic performance of the best permanent magnet; 3. High cost performance.
