HIGINSON company plans to develop a new plunger hydraulic cylinder, which needs to purchase the supporting hydraulic directional control valves. Helen, who had just joined the company, stumbled when purchasing the hydraulic directional control valves. Helen has no hydraulic valve supplier and can only purchase from the original hydraulic valve manufacturer of the company. Half a month later, the engineer and technician of the company installed the hydraulic directional control valves purchased by Helen for commissioning, and the plunger hydraulic cylinder dropped intermittently with vibration and noise. The technician pointed out that the hydraulic directional control valves needed to be replaced. Helen contacted the original manufacturer of hydraulic directional control valve. Per the manufacturer, the delivered hydraulic directional control valves met the requirements of Helen's parameters, and the accuracy also fully met the standard. As a novice, Helen was helpless, and the technician did not specifically say why to replace the hydraulic direction control valves. She tried to contact the new hydraulic directional control valve manufacturer to solve the problem. Helen left a message on AAK website: why is the plunger hydraulic cylinder equipped with hydraulic directional control valve noisy? At this moment, we can't tell the reason. After communicating with Helen, I learned the process of purchasing this hydraulic directional control valve and the judgment of technician in their company. AAK engineers are not 100% sure that where the problem is according to the hydraulic directional control valve drawings sent by Helen, the shipment sample of the original manufacturer and the video of their technician's machine test. We are thinking if Helen, as a novice, has mistaken the type of hydraulic directional control valve? The hydraulic directional control valves can be divided into internal leakage type and external leakage type. Combined with the working conditions, this plunger hydraulic cylinder just reverses the oil outlet chamber, and the back pressure is high. If the internal leakage hydraulic directional control valve is used, there will be abnormal phenomena such as vibration or noise. We told Helen our thinking. She really did not note to the original manufacturer that the hydraulic directional control valve is internal leakage or external leakage. I told her that AAK has ready-made samples of the external leakage hydraulic directional control valve. It is recommended to test the machine with AAK hydraulic directional control valve to see if there is still vibration or abnormal noise. A week later, Helen sent an email saying that AAK hydraulic directional control valve was installed and there was no abnormality in the test run.
The hydraulic directional control valve with internal leakage of 2drops/min makes AAK have no peers Oliver comes from a hydraulic equipment company in Canada. At the end of last year, they planned to develop a hydraulic cylinder that uses a hydraulic directional control valve. The parameter requirements are high, especially the internal leakage should be less than 2drops/min. Oliver inquired about more than 10 manufacturers of hydraulic directional control valves. Only one supplier who had cooperated for 5 years told him that he was 90% sure. Other manufacturers surrendered. One month later, the hydraulic directional control valve was installed with the oil cylinder. Less than 12 hours after startup, the hydraulic oil cylinder was unstable during reciprocating motion. After disassembly, the engineer found that the hydraulic directional control valve had internal leakage exceeding the requirement of 2 drops/min. Oliver was very helpless. He continued to look for new manufacturers of hydraulic directional control valves, and they all basically replied that they could not meet the requirement of internal leakage. Oliver found an article on Google, "The internal leakage index is equaled to the local manufacturer in Germany, but AAK hydraulic threaded cartridge valve has better cost performanceâ??, and left a message on our website: can you customize the hydraulic directional control valve with internal leakage of 2drops/min? At first glance, I knew that this was an accurate customer consultation. Although the internal leakage of 2drops/min was difficult, AAK had mass production 1 year ago. We suggested him send us the drawings and working condition requirements of the hydraulic directional control valve, and AAK can make samples directly. If the internal leakage of the hydraulic directional control valve does not meet the standard, 100% of the development cost will be returned. According to the development data provided by Oliver, there may not be any other manufacturer that can provide guarantee except AAK. After 30 days, AAK successfully sent 8 hydraulic directional control valve samples. Three months later, Oliver informed that no abnormality of the hydraulic directional control valve was found during the 3 internal commissioning of his company. After the hydraulic cylinder was tried out by the user, the feedback was also very good. Oliver is curious about the hydraulic directional control valves surrendered by so many manufacturers. Why did AAK samples succeed at one time? AAK hydraulic directional control valve has 3 absolute advantages and has already surpassed its domestic counterparts: 1. The precision honing machine imported from the United States is used to finish the valve hole and valve spool of the hydraulic direction control valves for more than 3 times. The dimensional accuracy of the valve hole is IT7 ~ 4, and the surface roughness can reach Ra 0.32 ~ 0.04�¼m, thus meeting the requirements of high accuracy.
Customer reversed internal and external leakage of the hydraulic directional control valve, causing vibration, AAK new design solved it all at once Stephen is from Hi-Force hydraulic equipment manufacturing company in the UK. In the second half of last year, he was promoted to the purchasing manager of Kuala Lumpur Branch due to his excellent work. Within a week of taking office, he met with complaints. A batch of their hydraulic cylinders were noisy and vibrated seriously during operation. The after-sales engineer failed to solve the problem within 3 days. The user was not satisfied. Stephen was a little worried. Stephen browsed an article of AAK on Google: "change the design of the hydraulic directional control valve, the vibration disappeared, and AAK eliminated the Canadian factory at zero cost", and left a message: how to solve the noise and vibration of the hydraulic cylinder? After reading this message, I roughly judged that either the hydraulic directional control valve used had problems or the original design had hidden dangers. We asked Stephen to provide the hydraulic system schematic diagram and design drawings, and AAK engineer judges that the working principle of the hydraulic cylinder is reasonable, only by checking on site can we find out the source of the vibration, and then no news from Stephen. 2 weeks later, Stephen emailed that according to the last case that AAK solved the vibration of the hydraulic cylinder, they also added a triangular throttling groove to the hydraulic direction control valve, but after installation, the hydraulic cylinder still vibrated. Their engineers said that AAK solution was a lie. I was speechless and didn't want to explain anything, so I ignored him. 3 days later, Stephen emailed us again, and sent a video of the hydraulic cylinder working and asked our help to check. AAK engineers found that the hydraulic cylinder will emit rhythmic noise and vibration whenever the load drops in the actual work, and preliminarily judged that there is a problem with the hydraulic direction control valve. AAK technical team discussed again according to the drawings, the working principle diagram of the hydraulic cylinder and the working video of the hydraulic cylinder, and confirmed that the problem lies in the hydraulic direction control valve. I told him that AAK could redesign the hydraulic directional control valve and asked him to send us samples of the original hydraulic directional control valve. Stephen may have no choice but promised. 5 days later, we received the sample of the original hydraulic directional control valve, which confirmed the judgment of our engineers that the internal leakage and external leakage of the original hydraulic directional control valve was reversed. 1 week later, AAK sent the newly designed external leakage type hydraulic directional control valve. Stephen informed by email that the noise and vibration problems of the hydraulic cylinder had been
AAK hydraulic directional control valve, which has been used for 2 years, is free of rust and corrosion. It stands out from 3 hydraulic valve manufacturers. Joseph finally received a large order for 1000 hydraulic directional control valves from customer. Joseph is the purchasing manager of a hydraulic pump company in Italy. Two years ago, the company received a test order for a special chemical hydraulic pump, which needs a hydraulic direction control valve. The customer requires that after 2 years, if the hydraulic directional control valve is free of rust and corrosion, it will have the opportunity to obtain a large order. The boss asked Joseph to find a very professional hydraulic valve manufacturer. Joseph knew that relying only on the existing hydraulic valve suppliers is not enough to guarantee the quality. He checked with all the hydraulic valve manufacturers he had contacted before and the new ones searched online, and selected 16 hydraulic valve factories, including AAK Hydraulic Valve. He asked all hydraulic valve manufacturers to provide 2 samples of hydraulic directional control valves according to the drawing requirements of the customer for testing at their headquarters. According to the post analysis to the drawing of hydraulic directional control valve from Joseph, we found that there is no problem to meet the accuracy, sensitivity and durability of this hydraulic directional control valve, except that the finish of the outer surface of the hydraulic directional control valve must be free of abnormality, rust and corrosion after 2 years of use, which is too uncertain. We didn't receive email from Joseph until 15 days after we sent out the hydraulic directional control valve samples. According to their simulation test, only the hydraulic directional control valves from 3 factories can be approved to send samples to their customer. It would take 2 years for AAK to know if we can get the order of hydraulic directional control valve. At that time, we were very surprised that there were such strange customers. We almost forgot the test order of this hydraulic directional control valve 2 years ago. Last week, Joseph sent an email asking about the production time and new price of 1000 hydraulic directional control valves, and told us that the surface of the hydraulic directional control valves from other two hydraulic valve manufacturers began to have scratches, corrosion, fading and rust after more than a year of use, only the surface gloss of AAK hydraulic direction control valve does not change. In fact, when we sent out the hydraulic directional control valve samples, we were not 100% sure to meet this special requirement, because we used a new process to proofing. We know that the conventional nickel plating, chromium plating, zinc plating, blackening and other processes basically can not keep the same appearance after 2 years of use. We adopted electroless nickel plating.
Dear buyer, if you find the cost is not adequate after joining the shopping cart, please contact us! We will adjust the rate according to your situation. Do not worry about any problem. We guarantee product quality and after-sales service. Contact us and you will get what you want. This is the 2P80F-OT hydraulic directional control valve, if you need another hydraulic directional control valve, please contact us or keep in mind.
1. Inner check valve: the check valve inside the valve body is to insure the hydraulic oil will not be returned. 2. Inner relief valve: the relief valve inside the valve body is able to adjust the hydraulic system working pressure. 3. Oil way: parallel circuit, with power beyond. 4. Control way: manual, air, air&electric, micro-switch, electric&hydraulic control. 5.Valve construction: monoblock construction, 1-8 levers are available to assembled as you requests. 6.Spool function: o, a, y , p etc. 7. Flow 40 l/min with pressure 160bar, 200bar, 315bar 8.Spool returning type with t (spring return) and w (ball locking) 9. Joining port: l (screw connection) 10 .Nominal diameter: g1/2; g3/8; m18*1.5
Supplier: Hydraulic Directional Control Valve.
Some time ago, , from a Hydraulic Valve Company in UK, fell in a batch of hydraulic directional valves purchased in Ningbo. There had some email communication between HYDRAULIC VALVE and , but maybe the fate has not yet arrived, we did not cooperate until last month this year. Steven regained his confidence because he had suffered a waterloo and got back a key game here in . At the beginning of this year, a batch of hydraulic directional valves purchased by Steven in Ningbo were stuck and failed during the test run, resulting in the failure of the whole batch of equipment to start up and run. His customer asked UK company to solve it within 30 days, otherwise there will be a big claim. Steven informed the original hydraulic valve manufacturer of these conditions, but the manufacturer prevaricated that it was a problem caused during the assembly process and had no direct relationship with them. Steven also consulted other hydraulic valve manufacturers. They either replied that the hydraulic valve was not produced by them and could not give the corresponding strategy, or there was no reply. Steven received serious rebuff here and there, and feel stressed. When contacted HYDRAULIC VALVE, we were willing to cooperate with him to solve this problem because we felt his trust in HYDRAULIC VALVE. Through his email description, we were still not sure what the problem is, and asked him to send us samples. After HYDRAULIC VALVE received the hydraulic directional valve samples from Steven, we felt that the relative sliding between the middle valve column and the valve body was not smooth. When the whole hydraulic directional valve is disassembled, there are slight scratches on the column surface, the valve body hole has a negative tolerance, and the valve body column hole has plastic distortion. Further microscopic examination showed that the surface of the material was etched badly. It is certain that the original hydraulic valve manufacturer has problems in material selection and heat treatment of alloy steel. Then we informed Steven of the result in a report and attached our suggestions for this style of hydraulic directional valve. After receiving the report, Steven seemed to see hope and asked us to make 5 hydraulic directional valve samples for his customer to run successfully first. After knowing the working conditions of this hydraulic directional valve, we adjusted the material selection of alloy steel, and increased the overall hardness of the hydraulic directional valve by 30% on the original basis. week after Steven received the samples, he informed HYDRAULIC VALVE by e-mail that the hydraulic directional valve samples made by were started up smoothly as soon as they were tested on the machine. When the new delivery date and order quantity were confirmed by his customers, he was finally relieved.
Hydraulic directional control valve troubleshooting, in only half of the time given by Leo, AAK HYDRAULIC VALVE used Fluororubber Sealing Ring and solved the problem of the hydraulic directional control valve troubleshooting that the other hydraulic valve manufacturers have not been able to solve, so that Leo can sleep at ease. This morning, just after reading the emails in the office and preparing for a cup of coffee, my colleague forwarded me an international express. I was a little surprised that there was no parcel notice from any customer, who sent the hydraulic valves to AAK? Will it be a complaint? I haven't met this for several years. I opened the package in fear. There are 5 new hydraulic valves inside. After simple inspection, they should be hydraulic directional valves. Looking at the sending address and person, it turns out that it belongs to the old customer Leo. This guy likes to make this sudden attack. Open the face book and I ask him, these are hydraulic directional valves. What do you need me to do? Leo said, hydraulic directional control valve troubleshooting, can you do it? I'm not good at the hydraulic directional control valve troubleshooting. He didn't reply. I immediately joked that I'm not good at the hydraulic directional control valve troubleshooting, which doesn't mean that AAK HYDRAULIC VALVE is also not good at the hydraulic directional control valve troubleshooting. AAK HYDRAULIC VALVE valve has its own technical team, which can help you on the hydraulic directional control valve troubleshooting. Leo commanded that I have 3 hours to go to bed. Give you 2.5 hours to finish the hydraulic directional control valve troubleshooting. I need to know where the hydraulic directional control valve troubles are and your solutions to the hydraulic directional control valve troubleshooting. After learning about his use scenarios of these hydraulic directional valves and media, I immediately asked AAK HYDRAULIC VALVE technical team to finish the hydraulic directional control valve troubleshooting within 2 hours. The AAK HYDRAULIC VALVE technical team simulated the use scenario of Leo's hydraulic directional valves under the pressurization and flow scenario. The test report came out soon. There were problems with the sealing rings of these hydraulic directional valves. At the same time, we suggested him use Fluororubber sealing ring to seal this hydraulic directional valve. We took 1.5 hours to finish the hydraulic directional control valve troubleshooting, which is just half of the time given by Leo. After learning the result, Leo was relieved and could sleep at ease. The story turned out to be this: Leo purchased some hydraulic directional valves, 30% of the hydraulic directional valves have flow parameter problems. The hydraulic valve manufacturer has not been able to have solutions to the hydraulic directional control valve troubleshooting. The boss is very unhappy.
