All bearings Abec-1 to abec_7
Rolling bearing Iso 9001:2000 Gb/t19001--2000 idt Cartons , wooden
Backing bearing mainly used for cold cluster rolling mill's roller. This mill take the bearing's outer ring as working surface, generally there's 3 or 5set bearings mounted on each roller and even more, depending on its matching rule. The bearing has thick outer ring and thin inner ring, high accuracy up to abec-7. Cylindrical roller bearing based on two or three rows of rollers and are available as full complement bearings (without cage) or as caged bearings. The advantage of the bearings without flanges lies in their particularly simple geometrical form and their very high radial load carrying capacity. Cylindrical roller backing bearings without flanges or flange rings cannot accommodate any axial load. So it is necessary to position thrust washers of bronze or plastic between the side faces of the outer ring and the support saddles. Thrust washers are not required with backing bearings with flanges (or flange rings) as the design of these bearings enables them to accommodate simultaneously acting radial and axial forces. For different requirement, zsj's backing bearing could fall in 2 classes by material: vacuum-degassed bearing steel and electroslag cemented bearing steel. Combined with advanced heat-treatment, grinding process, the bearing's quality is highly reliable. Zsj standard packing
Zsj products Sendzimir mill rolling bearing This bearing has been specially developed for cold rolling mills of the cluster type, but can also be used for other applications, e.G. Straightening or bending machines. This bearing is a roller bearing has a particularly thick-walled outer ring and can be mounted on stationary support shafts to form back-up or straightening rolls. The forces from the work rolls are transmitted via the support shaft and a system of support saddles to the roll or machine stands. The bearing for cluster mills is produced in many designs but is generally based on double or three-row cylindrical roller bearings. Single row needle roller bearing and Double row tapered roller bearing designs are also available. The logarithmic contact profile between rollers and raceways produces a vastly improved stress distribution under all load conditions as well as when the bearing is misaligned under load. An optimized finish on all surfaces in contact serves to enhance lubrication conditions. As lubricant is supplied to the bearings via the support shaft, the bearings have lubrication holes and some have one or more annular grooves in the inner ring. --individual wooden box packing --unique pe material inside box protection --epal standard pallet --vacuumize plastic bag packing if customer requires
China cylindrical roller bearings NU5244M made for rolling mills, single wrapped in a wooden case and ready for shipment in 2 days. Size of NU5244M bearings are 220X400X133.4mm,Mass 79.38kgs.
roll shaft bearing Material:ZG30Mn Weight:3-10t Process:sand casting Description: the main parts of coal grinding machine Function: Roller shaft bearing is the main accessories of grinding machine, connection roller cover and the bearing seat, and easy to open the shaft bearing and maintain it after open the roller cover
Four Row Cylindrical Roller Bearing Rolling Mill Bearing FCD6492240/804571/BC4B 322216/VJ202 Inner Ring: 320.000mm Outer Ring: 460.000mm Width: 240.000mm Chamfer: 3mm Outer diameter of Inner Ring:364.00mm Basic Dynamic Load Rating: 3370KN Basic Static Load Rating: 7550KN Gross Weight: 141kg Material: Carburizing Steel Four row cylindrical roller bearings as rolling mill bearings are mainly used on rolling mill stands, calenders and roller presses. The four rows of rollers lends itself to carry large radial loads, but no thrust capacity, for the given bearing cross section. Four row cylindrical roller bearings are separable, the rings and rolling elements could be separated, it is convenient to wash, check, mount and dismount. Four-row cylindrical roller bearing can only bear radial load; therefore, they must be installed with groove ball bearings or angular contact ball bearings, it will be the latter which bear the axial load. our row cylindrical roller bearings are classified into FC, FCD, FCDP types. Type FC four row cylindrical roller bearing consists of two outer rings and one inner ring, which have two ribs on outer rings, a center rib in the middle, and the inner ring without rib. Essentially, type FCD four row cylindrical roller bearing is formed by two type NN type of double row cylindrical roller bearings, so it has double outer rings, double inner rings, and the inner ring without rib. Type FCDP four row cylindrical roller bearing consists of two outer rings and two inner rings, which have two ribs on outer rings. Type FC, FCD and FCDP four row cylindrical roller bearings permit axial displacement in double directions of the housing relative to the shaft. Therefore, they are suitable to be used as non-locating bearings. Normally, their cages are made from solid machinery. I.D Size range: above 150mm FC3045120: 150mm*225mm*120mm FC3045120: 150mm*225mm*120mm FC3248168: 160mm*240mm*168mm FC3652168: 180mm*260mm*168mm FC3656180: 180mm*280mm*180mm FC3852168E: 190mm*260mm*168mm FC4058192: 200mm*290mm*192mm FC4462192: 220mm*310mm*192mm FC4666206: 230mm*330mm*236mm FC4668260: 230mm*340mm*260mm FC4866220: 240mm*330mm*220mm FC4872220: 240mm*360mm*220mm FC5275500YA3B2: 260mm*360mm*200mm FC5274220: 260mm*370mm*220mm FC5276280: 260mm*380mm*280mm FC5476230: 270mm*380mm*230mm FC5678220: 280mm*390mm*220mm FCDP5678275: 280mm*390mm*275mm FC5882240: 290mm*410mm*240mm FC6084240: 300mm*420mm*240mm FCD6084300: 300mm*420mm*300mm FCD6084300A: 300mm*420mm*300mm FC6896280: 340mm*480mm*280mm FCDP96130450: 480mm*650mm*450mm FCD96136500: 480mm*680mm*500mm
Housing washer raceway of thrust spherical roller bearing is sphere, has self-aligning ability, shaft to bearing is allowed to has a certain gradient, thrust spherical roller bearing has large axial loading capacity.Further more, when supporting an axial load, it can also bear a radial load which is not more than 55% of axial load. Normally thrust spherical roller bearings are lubricated with oil.
The spherical plain bearing is able to bear radial, axial load or the combined load. It boasts big load-bearing capacity and anti-impact ability and is characterized by anti-corrosion, anti-fraying, self-aligning, self-lubricate, dirty proof, etc.
Spherical roller bearings are inherently self-aligning and very robust. The two rows of rollers make the bearings able to carry heavy loads.The bearings have good self-aligning ability and can operate when the shaft deflection under load or the shaft deflection under load or the shaft misaligningment in mounting, and their permissible aligning angle is 1 to 2.5 degree.
