The attapulgite, that is, the attapulgite, is an aqueous magnesium-rich aluminosilicate clay mineral having a chain layer structure. Due to the special physical and chemical properties and process properties of attapulgite clay, it has been widely used in petroleum, chemical, building materials, papermaking, medicine, agriculture and so on. The current domestic use of coatings, drilling mud, edible oil decolorization. Mining equipment for processing attapulgite: 1. jaw crusher The preliminary coarse crushing processing of the attapulgite is carried out in order to better carry out the later grinding treatment. The device has the advantages of simple structure, large processing capacity, uniform crushing, low investment, small volume, and convenient operation and installation. 2. high pressure grinding mill The high-pressure grinding mill is the core equipment of attapulgite processing. It adopts a three-dimensional structure to save space, and it can form a systematic grinding process. The fine powder of attapulgite after grinding is excellent in quality and impurities. Less, the screening rate is 99.99%, and the fineness can be adjusted between 30-425 mesh. 3. bucket elevator Bucket elevator has good stone conveying function, its own driving power is small, the lifting range is large, the operation is reliable, the service life is long, and there are few faults. 4. electromagnetic feeder The electromagnetic feeder is to send the stone uniformly and orderly to the main machine, which has many features such as simple structure, no lubrication, uniform feeding and continuous. Attapulgite processing process: The large attapulgite is initially crushed by the jaw crusher, and is transported from the bottom up to the silo by the bucket elevator, and then uniformly and continuously fed to the main machine under the action of the vibrating feeder (high pressure grinding mill) Powder machine) The inner powder is processed by the powder separator. The fine powder that does not meet the requirements is returned to the main machine for re-grinding. The fine powder that meets the requirements enters the finished silo or the powder tanker with the pipeline device. Uniform packaging can be.
Dehong jaw crusher series are based on years experience and technology development. The continuous improvement and refinement has made them the preferred jaw crusher for professionals and our customers. They can meet most crushing requirements in primary and secondary crushing, and the largest compression resistance of the material is 320mpa. This series are widely used in stone mining, metallurgical, construction, smelting, hydraulic and chemical industries, etc.
we are the manufacturer to produce all kinds of accessories for iron works, such as centrifugal pump, spare parts for continuous caster, water-cooled furnace wall, water-cooled furnace cover and so on. We can supply you the best price and the best quality.
Features of jaw crusher 1)high crushing ratio. 2)even product granularity. 3)simple structure. 4)wide ranges of choice. 5)convenient maintenance. Working principle of jaw crusher: The motor transmits power through belt, drives the moving jaw to do periodic motion towards the fixed jaw by the eccentric shaft.The angle between toggle plate and moving jaw plate increases when moving jaw moves.So the moving jaw moves towards the fixed jaw.The stuff will be crushed in this process.The angle between toggle plate and moving jaw decreases when moving jaw moves down, the moving jaw moves leaves fixed jaw by pulling rod and spring, the final crushed stuff will be discharged from the outlet. Echo jiang
1. Brief introduction of cone crusher, symons crusher Cone crusher is generally used as a secondary crusher in a crushing circuit.Pre-crushed product (usually 3in minus depending on the cone crusher model) is fed through the top of the cone crusher and flows over the mantle.The vertical cone crusher drive shaft rotates the mantle eccentrically below the concave, or bowl liner, squeezing the product and
1. Working principle of stone impact crusher: This series of impact crusher is a new product designed by our company after absorbing the advanced technology.This kind of crusher can crusher many kinds of materials with max feed size less than 500mm and crushing strength less than 350mpa.It has the features of high ratio of crushing, reliable working, easy maintenance, etc.The final products are with cubic shapes and are ideal equipments for the highway, water and electricity construction.In addition, impact crushers are more suitable to process tranite, limestone, river gravel etc.In the area of highway construction, water cnservancy project and architecture. 2. Types of impact crusher We have various of impact crusher, such as pf0807, pf1007, pf1010, pf1210, pf1214, pf1315, pf1320 etc. In order to give you a responsible quotation, you can inform us the following information: 1). What's the material you are going to deal with? 2). What's the granularity of the material? 3). What's the granularity of the final products are you going to achive? 4). What's the producing capacity you are going to achieve? Our engineers will suggest you the most suitable one for you according to your information. Overall dim L*w*h(mm) 2210*1490*2670
Hello, we are the mine equipment supporting motor company, do you need the mining equipment supporting motor? We very much hope to cooperate with you. We sell YKK,YR,JS,JR,Y series motors, high and low voltage motors all the year round. Our contact information is
Supplier: Premium quality, certified & treated non gmo seed for planting, including: u.s.d.a. grade #1, 2, 3 corn seed, wheat seed, alfalfa seed, forage seed, barley seed, rice seed.
access to a wide variety of agricultural machinery & irrigation equipment including solar and wind.
bulk crude oil and various petrochemical loads including jet a1, en590, and w.t.i. to anywhere in the world a.s.w.p.
Services: Agricultural & farm design & construction consulting
Buyer: Excellent opportunity. needed: drilling rigs
Mining Equipment & spares
