Daikin Hydraulic Pump PV22 Brand new Made in Japan Quantity 110pcs
We are supplier and exporter of Hydraulic Oil. Our product is a high quality product made from imported oils and additives of best quality. It has a very good life and will give the best performance under the most critical conditions. It is available in 210 ltrs. Hdpe drum/ 26 ltrs. And 50 ltrs. Multi-brand Hydraulic Oils ISO VG 15, 32, 46, 68 and 100. Available in Drums, pails, IBCc, Bulk.
Principal Power steering system consists of a cylinder, a pump and handle. The oil is pressured from hydraulic pump and a handle(orbitrol) control a cylinder. The cylinder helps rudder move and the required oil is supplied from the hydraulic pump. Cylinder is classified Single, Rotary, Twin, Two rudders by torque and appearance Pump is classified Pulley type drived by engine and Power unit drived by electric motor We offer 7 kinds of handles with various appearance and functions. Features Narrow handle diameter helps you operate with small energy and power steering system offers light operation On where you put the handle, the rudder is fixed Structure that the rudder does not rotate even when the tide power the rudder When engine stops, manual steering is capable (Handle becomes heavy) You can choose the combination fit to your vessel Application Vessel above 350 HP A wide range of vessel from fishing boat to ferry
Can supply: ALUMINIUM LAMINATED FILM ROLLS, PRINTED STOCK LOT. Post industrial. Clean. Pack: in big bags. Can load in 1x40HC container aprox. 26 - 28 MT net. Ready for shipment. Photos available upon request. If you are interested kindly contact us for more information. You are welcome to visit our company premises and supervise our materials. Certificate ISO: 9001, ISO: 14001, OHSAS 45001, AQSIQ and CCIC
Principle Electric steering system is equl with the power steering system equipped a solenoid valve. It is the system which steers with solenoid valve by comparing resistance values of electric handle and rudder angle sensor It consists of a cylinder and a pump, an solenoid valve and a electric handle. The cylinder makes the rudder move and the pump supplies the oil to the cylinder. Handle is to swap the direction of hydraulic pressure Cylinder is classified Single, Rotary, Twin, Two rudders by torque and appearance Pump is classified Pulley type drived by engine and Power unit drived by electric motor We offer 7 kinds of handles with various appearance and functions. You can choose the combination fit to your vessel Key features Narrow handle diameter helps you operate with small energy and power steering system offers light operation The number of rotation wheel is 2.8 like the hydraulic handle Analogue type of a indicator for handle and a rudder angle indicator are applied. Controlled by Joystick / Autopilot USB port Autopilot can be used together. Application Vessel above 350HP A wide range of vessel from fishing boat to ferry
Our Y81 series hydraulic metal baling presses are drived by fully hydraulic power. This baling presses are mainly used in compressing the scattered plastic black and non-ferrous metal plates. It is very convenient for transportation and smelting. The baling presses adopted the electro hydraulic driver. They can be operated in both manual and automatic control modes. The operation is convenient and the performance is reliable. The mode of baling is side push. The baling block can be transported directly, so it will omit the porterage.--rogerweimail(at)sina(dot)com--- The technical features are as below: 1.the density of baling block is 2 T/M according to the requirement in third grade in conformity with GB4223-84 recycle Carbon Scrap Steel Category&Technique Terms. 2.the hydraulic station adopted the entirety type valve block, and its volume is small, and realize the partial non-pipe design, and it decrease the leakage. 3.the control valve adopted lishile series valves, changeover is stable and flexible, and noise is low. 4.optimizing the system design, assuring the oil temperature is not less than 55 5.the machine is driven by hydraulic system, and the electric system is automatically controlled by PLC.Controling is stable and modification is convenient. 6.the machine can be laid in the flattening concrete floor, and it needn't be made the foundation. 7.The discharge mode includes turn bag, push bag, fore push bag.
Hydraulic Baling Press from 40 tons to 150 tons capacity . Minimum weight 2.5 tons,packing to be done with wood.
Hydraulic baling press The production in our company contains hydraulic press; automatic hydraulic press ; automatic turning inside-out hydraulic press; large horizontal type hydraulic press; semi-automatic hydraulic press; hydraulicylinder; hydraulic lift and so on. All the productions had won the iso9001, 2000 stand.The production markets cover abroad and home. 1150*700*1700mm
Fasteners are the general term of the class of mechanical parts used in fastening two or more parts (or components) into a whole. It is widely used in energy, electronics, electrical appliances, machinery, chemical, metallurgy, mold, hydraulic and other industries, at the same time, in various kinds of machinery, equipment, vehicles, ships, railway, bridge, construction, structure, tools, instruments, chemical, instruments and supplies, you can see all kinds of fasteners, is the most widely used mechanical foundation parts. It is characterized by a wide variety of variety specifications, different performance uses, and a very high degree of standardization, series, and generalization. Therefore, a class of fasteners that already have national standards is called standard fasteners, or simply standard ones.
