AINiCo is composed primarily of Aluminum Nickel Cobalt and also Copper and Titanium. They are manufactured through either casting or sintering process. Cast AINiCo may be manufactured in complex shapes such as horseshoes not possible with other magnet materials. Sintered AINiCo offer slightly lower magnetic properties but better mechanical characteristics. it can be efficiently magnetized in any direction, and for anisotropic AINiComagnet, it generally has greater magnetic capacitive in a preferred orientation than isotropic types. AINiCo is hard and brittle, Machining or drilling cannot therefore be accomplished by ordinary methods. Holes are usually cored in at the foundry, and magnets are cast close to final size and then finish machined to closer tolerances. â?¢ Advantages of AlNiCo Magnet: 1.Customized designs are available. 2.Max working temperature can be as high as 550�°C. 3.Disadvantage: Br and BH(max)are not as high as rare earth magnet. 4.High energies and relatively low coercivity. 5.High magnetic flux density; low mold charge stable temperature properties; easy to shap.
Raw melting material - aluminum scraps, cans, engine waste etc. Output capacity - 5-30 tons/h, customized Automation - Full automatic/ half automatic (based on output requirement and investment budget Ingot type - ADC12 (7.5kg/ 10kg / customized) 1. After cleaning the oil and grease of waste aluminum, manually put it into the furnace with a forklift; 2. Ignition for melting furnace .Heat up to 680C, and input appropriate proportion of alloy elements. Heat up to 800C, melt and stir evenly, then fetch samples to the spectrometer for testing. Every lot of production need to do testing . 3. Put A tool that attracts iron into the furnace by forklift, to suck away the iron in the aluminum water. 4. Put the slag agent into Alu liquid to remove the slag. After slag removed , put the slags into Aluminum ash separation machine , and let the aluminum water and ash separate. The proportion of slag agent and aluminum liquid is 1:500 5.Open the drain valve and the aluminum water flows automatically to the ingot production line After the ingot casting is completed, the ingot stacking robot will stack the ingots, which means the production is completed.
1,Hight prurity (99.99% min) Metal Antimony (Sb) 2,4N>99.99%, 5N>99.999%, 6N>99.9999%, 7N>99.99999% 3,Lumps/Ingot/Granule/Bar 4,Color: Gray 5,Atomic weight: 121.760 6,Electronegativity: 2.05 7,CAS No.: 7440-36-0 8,Density: 6.697 g/cm3 (25â??) 9,Melting Point: 630.63 â?? 10,Boiling Point: 1587 â?? 11,Mainly used for the preparation of â?¢ - V compound semiconductor InSb, Bi2Sb, GaSb, high purity alloys, electronic refrigeration element materials and germanium, silicon single crystal dopants.
Metal tin is mainly used in the manufacture of alloys. Tin and sulfur compounds - tin sulfide, which is similar in color to gold, is commonly used as a gold pigment. Tin's modern application is as a solder for the electronics industry. Used in various purities and alloys (often with lead or indium), tin solders have a low melting point, which makes them suitable for bonding materials. Standard ASTM B29-03, BS EN 12659:1999, GB/T 469 -2005 , Content Pb â?¥ 99.99 % Density 11.34 g / cm 2 Color Bluish Weight 35 kgs / lump, 55 kgs / lump Dimension 21" x 4" x 2.5" Package Standard Sea-worthy package, fixed by belt per ton Shape Rectangular Lump Application lead-acid storage batteries Ammunition, cable sheathing, and building construction materials counterweights, battery clamps cast products such as: bearings, ballast, gaskets, type metal, terne plate, and foil Container Size 20Gp - 2.352(width) *2.385 ( Height ) * 5.90 ( Inside length ) Meter 40Gp - 2.352(width) *2.385 ( Height ) * 11.8 ( Inside length ) Meter 40HQ - 2.352(width) *2.69 ( Width ) * 5.90 ( Inside length ) Meter
Inch Deck Screws: Deck screws are screws specifically designed for use in outdoor decking projects. They are usually corrosion-resistant to withstand exposure to the elements. The "inch" specification likely refers to the length of the screws.
SPECIFICATIONS: the following Percentage Points: Chemical Composition Carbon - 0.54 to 0.82% Phosphorus - 0.035% max Manganese - 0.60 to 1.05% As. - 0,01max of Mass share Silicone - 0.18 to 0.40% Sulphur - 0.035% max Norms - R-50 GOST-7173-75 / R-65 GOST- 8165-75 The scrap consists of R-50 (51,67 KG/m) R-65 (64,72KG/m) Used Rails shall be considered free of alloys when the residual alloying elements do not exceed Cut to 1.5 meter length (standard) 1. Technical terms: USED RAIL R50-R65 2. Specifications and Chemical Composition: Used Rail: R50 (51.67KG/Meter, GOST 7173-55), Used Rail: R65 (64.72KG/Meter, GOST 8161-75). Size & Weight: Length: 12meter ~ 12.5meter Maximum or less according tobuyerâ??s instruction; Expenses on seller Width: 5.5 inches ; Weight: 64.72Kg. No fishplates or steel pieces or bolts are attached to the used rails. All rails are clean and straight. No pitting. Only atmospheric rust No heavy rust. It is mandatory that Rails must be cut into length 1.5 meter(max.) before shipment.
Supplier: Valves & forged fittings.
KHODIYAR INDUSTRIA PVT LTD is an ISO-9001:2015 certified Hot Forging & Machined Components manufacturing facility produce all grades of Brass, Copper & Alloys, Aluminium & Alloys, Carbon Steels, Alloy Steels & Stainless Steel in the weight range of 50 GMS to 35KG as a single part to suit your production requirements. We were established in 2014 & produce Forged & Machined components for OEMs in Heavy Engineering, Pump, Valve, Wind turbine, Automotive, Electrical, Aerospace Industry, Oil, Power & Gas, Material Handling, Construction & Mining Equipments, Defense etc., to list a few applications. Our Forge shop includes : a. 100 MT Screw Press Product weight:0.050 0.500 Kgs. + Equivalent Trimming Press (40 MT) b. 200 MT Screw Press Product Weight: 0.100 Kg to 2.000 Kgs. + Equivalent Trimming Press (75 MT) (Non-Ferrous 4 Kg.) c. 300 MT Screw Press Product Weight: 0.100 Kg to 3.000 Kgs. + Equivalent Trimming Press (100 MT) (Non-Ferrous- 5 Kgs.) d. 1 Ton Drop Hammer & 2 Drop Hammer e. Furnace : Oil, Electric, Gas & Coal. MACHINE SHOP 1. Vertical Machining center - BFW ( 800*550*500 MM ) BED SIZE with 4th axis 2. Vertical Machining center - HAAS make ( 800*550*500 MM ) BED SIZE with 4th axis & 3. Turning centers - up to 350 MM DIA. Jobs can be turned
Heavy melting steel is a designation for recyclable steel. It is categorised into two major categories: HMS 1 and HMS 2. The difference between the two is HMS 1 does not contain galvanized and cast iron, whereas HMS 2 does. Because both grades guarantee a minimum piece thickness â?? at least 1/4inch (6.3mm) for HMS 1, and 1/8 in for HMS 2 â?? consignments have a high density. The typical constituents are plates, truck parts, structural items, large machinery parts, automatic parts, pipes, post consumer steel goods. Chemical Composition: C:0.06 â?? 0.082% Mn:0.75 â?? 1.05% SI:0.13 â?? 0.28% P: Max 0.035% S: Max 0.045% Ar: Max 0.15%
Model NO : OEI - 717 TC 1400 Watts Power Steam / Burst / Spray Ironing German Grade Non Stick Coated Sole Plate Cast In Sole Plate Technology for Faster and Uniform Heating Button Groove: Reaches into Tricky Areas Adjustable Steam Control Thermostat for Variable Temperature Control Thermal Fuse for Over Heat Safety Protection Shock Proof Plastic Body Silk Braided 360 degree Swivel Cord for Easy
