Features:
1. Our pumps applied the single or double vane structure so that it can transfer sewage easily. It can transfer the fibrous matter which is with bore 5 times than pumps.
2. Seal the pumps with material tungsten carbide which is new, tough and corrosion resistant. All the same time we seal up the pumps with double-end, make it working in the oil chamber with long time safely, at least more than 8, 000 hours.
3. The structure of our pumps is portable, minimum-volume, non-noise and distinct energy-saving effect. Our pumps are convenient to repair and they can work as long as been put in water, this will save the cost much.
4. We installed the leak detection sensor which is high-precision and anti-jamming in the sealed oil chamber which can protect the pumps totally.
5. We can equip the automatic safety control cabinet according to the request from customer. Protect the leak, over-temperature and over-weight totally.
6. Float switch can adjust automatic according to the liquid, it can control the start and stop of pump, need not person to operate, it is very convenient for using.
7. We can equip double guide rail automatic coupling installation system according to the needs from customer; it can be convenient for repair and installation.
8. Our pumps can be used in the range and assurance the electrical machinery will not be overload.
9. There is 2 ways for installation: fixed type automatic coupling installation system and mobile free installation system.
Flow: 15m3/h
Head: 39m
Power: 4kw
Material: cast iron
Medium: clean water
Outlet dia: 50mm
Diameter: 175mm
Speed: 2850r/min
Voltage: 380V
Phase: 3 phase/50Hz
Color: Blue
QJ Submersible pumps Parameters:
Flow range10~500m3/h, Lift scope within 5~405m;
Caliber scope 32~203mm, Temperature range-15~80° C.
Products Overview:
QJ Series submersible pumps widely used in farmland irrigation, spray irrigation and water-use, industrial and civil buildings, also the drainage system to level hills, mountain diversion and in low-lying areas dunes, urban and rural mining supply, drainage and other water conservancy facilities. Characteristics are that they are assembled into a simple structure they have installation convenience a small footprint, simple maintenance and a safe reliable operation.
Product use conditions:
QJ Submersible pumps use conditions
1. 380 V bias voltage does not exceed + -5% and 50 HZ frequency, and the deviation is not more than + -1% of the three-phase power supply.
2. Electrical cavity must be filled with water.
3. The first-class pump impeller should at least go into the dynamic water level 2 m below surface. Static pump unit immersed under water shall not be greater than 70 m.
4. Electrical from the bottom of the bottom of the well shall be not less than 3 m.
5. The water temperature no higher than 20 ° C, QJR-temperature hot water pump up to 80 ° C.
6. Water and sand content (by mass) of not more than 0.01%.
7. Water PH 6.5-8.5.
8. The hydrogen sulfide in water content is not more than 1.5 mg / L.
Application :
deep well water
farm irrigation
sprinkling irrigation
urban and rural industry
mine supply and drainage.
Shenlong pump Ltd is located at the beautiful shore of the Yellow River and at the foot of the mountains of Mangshan, ZhengZhou City in the heart of Henan province.
The company was created in the 1980s, And after the company's combined relentless efforts has become one of the largest modern enterprises in Henan that combines Research and Development (R&D), Prototype Design, Product testing, Advanced industrial production, and operational excellence.
Shenlong pump Ltd is a design manufacture export professional company. Our Enterprise is Ministry of Agriculture. We are production and sales pumps around the world. The manufacture have strong technical force, with all kinds of machine tools, planer, drill press, etc. and The manufacture's total land area of over 660000 Square meters and with in excess of 300 equipment sets. Employing 860 staff members; amongst them over 40 senior technical experts. The allocation of B-level exceeds the national standard of computer Pump testing centers.
Sea water submersible pumps are high-performance, wear-resistant pumps which are produced by international advanced technology. Our products have no pollution to water environment by using advanced oil-filled or water-filled stainless steel motors. Our products are made of quality stainless steel shell, shaft, coupling and the new floating impeller has no axial pressure load to the motor. The water power pattern layout's impeller, raised the efficiency, saved the run cost. Electrical machinery and water pump vertical connection, therefore only need the small installment space. The built-in check valve, is loaded with the prevent returning valve in the pump upper extreme body, prevent water hammer impact. ge impellers series connestion
Application:
1. offshore platform fire-fighting,
2.thermal dissipation,
3.seawater desalinization, seawater lifting,
4.coastal square fountain,
5.mariculture and attemperation as ground source heat pump in coastal area.
Flow: 10m3/h
Head: 40m
Power: 2.2kw
Material: cast iron
Medium: clean water
Outlet dia: 32mm
Diameter: 175mm
Speed: 2850r/min
Voltage: 380v
Phase: 3 phase/50hz
Color: blue
Qj submersible pumps parameters:
Flow range10~500m3/h, lift scope within 5~405m;
Caliber scope 32~203mm, temperature range-15~80° c.
Products overview:
Qj series submersible pumps widely used in farmland irrigation, spray irrigation and water-use, industrial and civil buildings, also the drainage system to level hills, mountain diversion and in low-lying areas dunes, urban and rural mining supply, drainage and other water conservancy facilities. Characteristics are that they are assembled into a simple structure they have installation convenience a small footprint, simple maintenance and a safe reliable operation.
Product use conditions:
Qj submersible pumps use conditions
1. 380 v bias voltage does not exceed + -5% and 50 hz frequency, and the deviation is not more than + -1% of the three-phase power supply.
2. Electrical cavity must be filled with water.
3. The first-class pump impeller should at least go into the dynamic water level 2 m below surface. Static pump unit immersed under water shall not be greater than 70 m.
4. Electrical from the bottom of the bottom of the well shall be not less than 3 m.
5. The water temperature no higher than 20 ° c, qjr-temperature hot water pump up to 80 ° c.
6. Water and sand content (by mass) of not more than 0.01%.
7. Water ph 6.5-8.5.
8. The hydrogen sulfide in water content is not more than 1.5 mg / l.
Application :
Deep well water
Farm irrigation
Sprinkling irrigation
Urban and rural industry
Mine supply and drainage.
180W, 1" outlet diameter, Max. flow with 133 l/min, Max. head with 7m, Max. diameter of particle with 15mm, Max. submersible depth with 5m, Maxi. fluid temperature with 40 liquid PH valve: 4-10, Class B, IPX8,
18.5*18*36.5cm for each piece and each carton, G.W. is 9kgs
Flow: 10m3/h
Head: 95m
Power: 5.5kw
Material: cast iron
Medium: clean water
Outlet dia: 32mm
Diameter: 175mm
Speed: 2850r/min
Voltage: 380v
Phase: 3 phase/50hz
Color: blue
Qj submersible pumps parameters:
Flow range10~500m3/h, lift scope within 5~405m;
Caliber scope 32~203mm, temperature range-15~80° c.
Products overview:
Qj series submersible pumps widely used in farmland irrigation, spray irrigation and water-use, industrial and civil buildings, also the drainage system to level hills, mountain diversion and in low-lying areas dunes, urban and rural mining supply, drainage and other water conservancy facilities. Characteristics are that they are assembled into a simple structure they have installation convenience a small footprint, simple maintenance and a safe reliable operation.
Product use conditions:
Qj submersible pumps use conditions
1. 380 v bias voltage does not exceed + -5% and 50 hz frequency, and the deviation is not more than + -1% of the three-phase power supply.
2. Electrical cavity must be filled with water.
3. The first-class pump impeller should at least go into the dynamic water level 2 m below surface. Static pump unit immersed under water shall not be greater than 70 m.
4. Electrical from the bottom of the bottom of the well shall be not less than 3 m.
5. The water temperature no higher than 20 ° c, qjr-temperature hot water pump up to 80 ° c.
6. Water and sand content (by mass) of not more than 0.01%.
7. Water ph 6.5-8.5.
8. The hydrogen sulfide in water content is not more than 1.5 mg / l.
Application :
Deep well water
Farm irrigation
Sprinkling irrigation
Urban and rural industry
Mine supply and drainage.
Flow: 10m3/h
Head: 180m
Power: 13kw
Material: cast iron
Medium: clean water
Outlet dia: 32mm
Diameter: 175mm
Speed: 2850r/min
Voltage: 380V
Phase: 3 phase/50Hz
Color: Blue
QJ Submersible pumps Parameters:
Flow range10~500m3/h, Lift scope within 5~405m;
Caliber scope 32~203mm, Temperature range-15~80° C.
Products Overview:
QJ Series submersible pumps widely used in farmland irrigation, spray irrigation and water-use, industrial and civil buildings, also the drainage system to level hills, mountain diversion and in low-lying areas dunes, urban and rural mining supply, drainage and other water conservancy facilities. Characteristics are that they are assembled into a simple structure they have installation convenience a small footprint, simple maintenance and a safe reliable operation.
Product use conditions:
QJ Submersible pumps use conditions
1. 380 V bias voltage does not exceed + -5% and 50 HZ frequency, and the deviation is not more than + -1% of the three-phase power supply.
2. Electrical cavity must be filled with water.
3. The first-class pump impeller should at least go into the dynamic water level 2 m below surface. Static pump unit immersed under water shall not be greater than 70 m.
4. Electrical from the bottom of the bottom of the well shall be not less than 3 m.
5. The water temperature no higher than 20 ° C, QJR-temperature hot water pump up to 80 ° C.
6. Water and sand content (by mass) of not more than 0.01%.
7. Water PH 6.5-8.5.
8. The hydrogen sulfide in water content is not more than 1.5 mg / L.
Application :
deep well water
farm irrigation
sprinkling irrigation
urban and rural industry
mine supply and drainage.
Shenlong pump Ltd is located at the beautiful shore of the Yellow River and at the foot of the mountains of Mangshan, ZhengZhou City in the heart of Henan province.
The company was created in the 1980s, And after the company's combined relentless efforts has become one of the largest modern enterprises in Henan that combines Research and Development (R&D), Prototype Design, Product testing, Advanced industrial production, and operational excellence.
Shenlong pump Ltd is a design manufacture export professional company. Our Enterprise is Ministry of Agriculture. We are production and sales pumps around the world. The manufacture have strong technical force, with all kinds of machine tools, planer, drill press, etc. and The manufacture's total land area of over 660000 Square meters and with in excess of 300 equipment sets. Employing 860 staff members; amongst them over 40 senior technical experts. The allocation of B-level exceeds the national standard of computer Pump testing centers.
Flow: 10m3/h
Head: 240m
Power: 15kw
Material: cast iron
Medium: clean water
Outlet dia: 32mm
Diameter: 175mm
Speed: 2850r/min
Voltage: 380V
Phase: 3 phase/50Hz
Color: Blue
QJ Submersible pumps Parameters:
Flow range10~500m3/h, Lift scope within 5~405m;
Caliber scope 32~203mm, Temperature range-15~80° C.
Products Overview:
QJ Series submersible pumps widely used in farmland irrigation, spray irrigation and water-use, industrial and civil buildings, also the drainage system to level hills, mountain diversion and in low-lying areas dunes, urban and rural mining supply, drainage and other water conservancy facilities. Characteristics are that they are assembled into a simple structure they have installation convenience a small footprint, simple maintenance and a safe reliable operation.
Product use conditions:
QJ Submersible pumps use conditions
1. 380 V bias voltage does not exceed + -5% and 50 HZ frequency, and the deviation is not more than + -1% of the three-phase power supply.
2. Electrical cavity must be filled with water.
3. The first-class pump impeller should at least go into the dynamic water level 2 m below surface. Static pump unit immersed under water shall not be greater than 70 m.
4. Electrical from the bottom of the bottom of the well shall be not less than 3 m.
5. The water temperature no higher than 20 ° C, QJR-temperature hot water pump up to 80 ° C.
6. Water and sand content (by mass) of not more than 0.01%.
7. Water PH 6.5-8.5.
8. The hydrogen sulfide in water content is not more than 1.5 mg / L.
Application :
deep well water
farm irrigation
sprinkling irrigation
urban and rural industry
mine supply and drainage.
Shenlong pump Ltd is located at the beautiful shore of the Yellow River and at the foot of the mountains of Mangshan, ZhengZhou City in the heart of Henan province.
The company was created in the 1980s, And after the company's combined relentless efforts has become one of the largest modern enterprises in Henan that combines Research and Development (R&D), Prototype Design, Product testing, Advanced industrial production, and operational excellence.
Shenlong pump Ltd is a design manufacture export professional company. Our Enterprise is Ministry of Agriculture. We are production and sales pumps around the world. The manufacture have strong technical force, with all kinds of machine tools, planer, drill press, etc. and The manufacture's total land area of over 660000 Square meters and with in excess of 300 equipment sets. Employing 860 staff members; amongst them over 40 senior technical experts. The allocation of B-level exceeds the national standard of computer Pump testing centers.
Qj submersible pumps parameters:
Flow range10~500m3/h, lift scope within 5~405m;
Caliber scope 32~203mm, temperature range-15~80° c.
Products overview:
Qj series submersible pumps widely used in farmland irrigation, spray irrigation and water-use, industrial and civil buildings, also the drainage system to level hills, mountain diversion and in low-lying areas dunes, urban and rural mining supply, drainage and other water conservancy facilities. Characteristics are that they are assembled into a simple structure they have installation convenience a small footprint, simple maintenance and a safe reliable operation.
Product use conditions:
Qj submersible pumps use conditions
1. 380 v bias voltage does not exceed + -5% and 50 hz frequency, and the deviation is not more than + -1% of the three-phase power supply.
2. Electrical cavity must be filled with water.
3. The first-class pump impeller should at least go into the dynamic water level 2 m below surface. Static pump unit immersed under water shall not be greater than 70 m.
4. Electrical from the bottom of the bottom of the well shall be not less than 3 m.
5. The water temperature no higher than 20 ° c, qjr-temperature hot water pump up to 80 ° c.
6. Water and sand content (by mass) of not more than 0.01%.
7. Water ph 6.5-8.5.
8. The hydrogen sulfide in water content is not more than 1.5 mg / l.
