Supplier: Cast iron skulls, cast iron borings and turnings, steels skulls, eaf skulls, plate iron, mill scale, metal scrap, incinerated scrap (e46)
The Incinerated scrap or E46, is the by-product derived from the reprocessing of incinerated domestic waste. After the combustion process, the furnace output (IBA Incinerator bottom ash) is firstly washed, magnetically separated and screened to separate any no ferrous material. At a visual inspection, the material is fragmentized, with iron and steel parts, resulting partly cut or in shredded form. The stock appears heterogeneous and contains all kind of cut or dismantled steel parts such as sheets, bars, frames, wires, bolts and other iron/steel household residues. The incinerated scrap is eventually oxidized, due to the thermal and cooling treatments, that the material has been submitted to. The burnt scrap also contains minor slag parts, ash and iron oxide, due to the recovery process. Such components are inherent and adhere to the scrap surface. The total impurities, can be sorted, but not fully removed. The consignment does not contain any type of arms, ammunition, mines, shells, cartridges, radioactive contaminated, or any other explosive material in any form either used or otherwise. The collected stock, is stored in open air, on cemented flooring. It can be loaded loose in 20â?? heavy duty container. Please feel free to contact us for further details.
AINiCo is composed primarily of Aluminum Nickel Cobalt and also Copper and Titanium. They are manufactured through either casting or sintering process. Cast AINiCo may be manufactured in complex shapes such as horseshoes not possible with other magnet materials. Sintered AINiCo offer slightly lower magnetic properties but better mechanical characteristics. it can be efficiently magnetized in any direction, and for anisotropic AINiComagnet, it generally has greater magnetic capacitive in a preferred orientation than isotropic types. AINiCo is hard and brittle, Machining or drilling cannot therefore be accomplished by ordinary methods. Holes are usually cored in at the foundry, and magnets are cast close to final size and then finish machined to closer tolerances. â?¢ Advantages of AlNiCo Magnet: 1.Customized designs are available. 2.Max working temperature can be as high as 550�°C. 3.Disadvantage: Br and BH(max)are not as high as rare earth magnet. 4.High energies and relatively low coercivity. 5.High magnetic flux density; low mold charge stable temperature properties; easy to shap.
Raw melting material - aluminum scraps, cans, engine waste etc. Output capacity - 5-30 tons/h, customized Automation - Full automatic/ half automatic (based on output requirement and investment budget Ingot type - ADC12 (7.5kg/ 10kg / customized) 1. After cleaning the oil and grease of waste aluminum, manually put it into the furnace with a forklift; 2. Ignition for melting furnace .Heat up to 680C, and input appropriate proportion of alloy elements. Heat up to 800C, melt and stir evenly, then fetch samples to the spectrometer for testing. Every lot of production need to do testing . 3. Put A tool that attracts iron into the furnace by forklift, to suck away the iron in the aluminum water. 4. Put the slag agent into Alu liquid to remove the slag. After slag removed , put the slags into Aluminum ash separation machine , and let the aluminum water and ash separate. The proportion of slag agent and aluminum liquid is 1:500 5.Open the drain valve and the aluminum water flows automatically to the ingot production line After the ingot casting is completed, the ingot stacking robot will stack the ingots, which means the production is completed.
Metal tin is mainly used in the manufacture of alloys. Tin and sulfur compounds - tin sulfide, which is similar in color to gold, is commonly used as a gold pigment. Tin's modern application is as a solder for the electronics industry. Used in various purities and alloys (often with lead or indium), tin solders have a low melting point, which makes them suitable for bonding materials. Standard ASTM B29-03, BS EN 12659:1999, GB/T 469 -2005 , Content Pb â?¥ 99.99 % Density 11.34 g / cm 2 Color Bluish Weight 35 kgs / lump, 55 kgs / lump Dimension 21" x 4" x 2.5" Package Standard Sea-worthy package, fixed by belt per ton Shape Rectangular Lump Application lead-acid storage batteries Ammunition, cable sheathing, and building construction materials counterweights, battery clamps cast products such as: bearings, ballast, gaskets, type metal, terne plate, and foil Container Size 20Gp - 2.352(width) *2.385 ( Height ) * 5.90 ( Inside length ) Meter 40Gp - 2.352(width) *2.385 ( Height ) * 11.8 ( Inside length ) Meter 40HQ - 2.352(width) *2.69 ( Width ) * 5.90 ( Inside length ) Meter
Cold Shot Nitrogen Deburring Machine Introduction Automatic deburring is a process for removing flash from molded rubber parts. We use liquid nitrogen, high - speed rotation and shot blasted plastic media in varying combinations to remove the flash in a highly precise, economical and expedient manner. Parts that have thin flash can be quickly and thoroughly cryogenically deflashed. This process is exceptionally good at removing the inner dimensional and complex flash that cannot be removed by any other method. Application O - rings, gaskets and other rubber sealings Insulators and other electric / electronic components Valve stems, washers and fittings Short tubes and flexible boots Rubber absorbers and bumpers for automobile Face masks & goggles Mobile phone housing and intelligent watch strap Zinc and mag alloys like door lockers for auto cars SPECIFICATIONS NS - 120C Size: L1400mm * W1300mm * H2300mm Weight: 1500kg Power Supply: AC380V 50HZ Electrical Capacity: 8KW * 3PH Design Temp: - 130Deg. C Design Pressure: 0.5 - 0.7 Mpa Outer Wall Material: SUS Frame Material: 100% SUS304 Barrel Capacity: 120L Wheel Speed: 6, 000 rpm Max Barrel Speed: 0 - 16rpm Media Throw wheel Size : 350 Operation Mode: Press Button
Supplier: Engineering goods like machined, forged, stamped, casting, aluminum casting, aluminum extrusion, fasteners, springs, washers, gaskets, oil seals, rubber components, etc
Supplier: Soda ash light / dense 99.2%
sodium bicarbonate
caustic soda flakes 99%
sodium sulphate anhydrous (ssa) 99%
sodium sulphite flakes (ssf) 60%
sodium metabisulphate
hydrogen peroxide (h2o2) 50%
formic acid 85%
glacial acetic acid
paraffin wax
liquid paraffin (white oil) lp 100
menthol crystal
fumed silica
deg (di ethylene glycol)
mono ethylene glycol (meg)
poly ethylene glycol (peg),
base oil 150n, bs 150, 600n
bitumen 60/70
rpo (rubber process oil)
lioh (lithium hydroxide)
hco (hydrogenated castor oil)
12 hsa (hydroxy stearic acid)
ferrous sulphate heptahydrate
additive for lubricating oil
aromatic chemicals
Services: Exporting of chemicals & other products
KHODIYAR INDUSTRIA PVT LTD is an ISO-9001:2015 certified Hot Forging & Machined Components manufacturing facility produce all grades of Brass, Copper & Alloys, Aluminium & Alloys, Carbon Steels, Alloy Steels & Stainless Steel in the weight range of 50 GMS to 35KG as a single part to suit your production requirements. We were established in 2014 & produce Forged & Machined components for OEMs in Heavy Engineering, Pump, Valve, Wind turbine, Automotive, Electrical, Aerospace Industry, Oil, Power & Gas, Material Handling, Construction & Mining Equipments, Defense etc., to list a few applications. Our Forge shop includes : a. 100 MT Screw Press Product weight:0.050 0.500 Kgs. + Equivalent Trimming Press (40 MT) b. 200 MT Screw Press Product Weight: 0.100 Kg to 2.000 Kgs. + Equivalent Trimming Press (75 MT) (Non-Ferrous 4 Kg.) c. 300 MT Screw Press Product Weight: 0.100 Kg to 3.000 Kgs. + Equivalent Trimming Press (100 MT) (Non-Ferrous- 5 Kgs.) d. 1 Ton Drop Hammer & 2 Drop Hammer e. Furnace : Oil, Electric, Gas & Coal. MACHINE SHOP 1. Vertical Machining center - BFW ( 800*550*500 MM ) BED SIZE with 4th axis 2. Vertical Machining center - HAAS make ( 800*550*500 MM ) BED SIZE with 4th axis & 3. Turning centers - up to 350 MM DIA. Jobs can be turned
