We put forward a high quality of assortment of Nickel which is available in many forms including LME registered and non registered cathodes, cut cathodes, briquettes, pellets, disks, shots, granules, foil, powder, flakes, sheet, wire, mesh, spheres, “evaporation slugs”, and rods. Nickel is a silvery white metal that takes on a high polish. It is hard, malleable, ductile, somewhat ferromagnetic, and a fair conductor of heat and electricity
We hold immense expertise in making available Copper in many forms including LME registered and non registered cathodes, billets, rods, cakes, bars, foil, sheet, granules, plates, powder, shot, turnings, wire, insulated wire, mesh and “evaporation slugs”. Copper is one of the most important metals. Copper is reddish with a bright metallic lustre. It is malleable, ductile, and a good conductor of heat and electricity (second only to silver in electrical conductivity). Its alloys, brass and bronze, are very important. Monel and gun metals also contain copper. The most important compounds are the oxide and the sulphate, (blue vitriol
We are able to supply Tin in many forms including LME registered and non registered, ingots, slabs, bars, foil, granules, powder, anodized activated powder, shot, wire, sticks, ingots, and “mossy tin”. Tin is a silvery-white metal, is malleable, somewhat ductile, and has a highly crystalline structure. The element has two colours, with a cubic structure which changes at allotropic forms. On warming it is grey, the ordinary form of the metal. When Tin is cooled below 13.2°C, it changes slowly from white to grey or tetragonal structure. This change is affected by impurities such as Aluminium and Zinc, and can be prevented by small additions of Antimony or Bismuth.
We are engaged in making Lead available in several forms including LME registered and non registered 99.97% and 99.99% as well as secondary ingots, foil, granules, powder, rod, shot, sheet, and wire. Lead is a bluish-white lustrous metal. It is very soft, highly malleable, ductile, and a relatively poor conductor of electricity. It is very resistant to corrosion but tarnishes upon exposure to air. Alloys include pewter and solder.
We offer a wide plethora of Zinc in many forms including LME registered and non registered Special High Grade Ingots and Jumbos, cathodes, dust, foil, granules, powder, pieces, anodize activated powder, shot, and a mossy form. Zinc is a bluish-white, lustrous metal. It is brittle at ambient temperatures but is malleable at 100 to 150°C. It is a reasonable conductor of electricity, and burns in air at high red heat with evolution of white clouds of the oxide. Plating thin layers of zinc on to iron or steel is known as galvanizing and helps to protect the iron from corrosion.
A unique product of Aluminum briquettes made from aluminum turning Aluminum contain 90% above.
Ferrite Magnet is manufactured from oxide material by powder metallurgical process. Its advantages include: low-cost excellent corrosion resistance, resistance to be demagnetized etc. The normal working temperature of Ferrite Magnet is between-40C and +250C.It can be magnetized before or after assembling. Generally, Ferrite Magnet can be machined to regular shapes like segments, blocks, rings and discs etc. The normal grades for sintered Ferrite Magnets are Y10,TY25, Y30, Y30BH, Y35, etc. Advantages of Ferrite Magnet: Ferrites have isotropic characteristics, weak magnetic performance, has the same magnetic performance in any direction, multipolar magnetic charge. The main raw material of ferrite is oxides, so it is not corroded by high temperature, high humidity or chemicals (except strong acid and base); with excellent diamagnetic impedance, no flux loss before and after assembly and magnetic charging; working temperature is-40C to + 250C, poor temperature coefficient; Br temperature coefficient is-0.2% /C, 0.2% under Br, etc. per 1 Cincrease; high hardness, wire cutting and grinding; ferrite is brittle and fragile during production and transportation. magnetic requirements and good for strict working environment requirement.
Neodymium magnets (also known as NdFeB, Neo or NIB magnets), are strong permanent magnets made from an alloy of neodymium, iron & boron. Part of the Rare-Earth magnet family, they have the highest magnetic properties of all permanent magnets. Due to their high magnetic strength and relatively low-cost, they are the preferred choice for many consumers, commercial, industrial and technical applications.NdFeB is divided into sintered NdFeB and bonded NdFeB. Bonded NdFeB is magnetic in all directions and corrosion resistance and is divided into Bonded Compression NdFeB Magnet and Bonded Injection NdFeB Magnet; while sintered NdFeB is easy to corrosion, the surface requires coating, generally divided into axial and radial magnetic charging. Advantages of Sintered NdFeB Magnet : 1. Very hard and brittle, high diamagnetic resistance, high cost / performance ratio, not suitable for high working temper ature; 2. Magnetic performance is higher than that of the rare earth cobalt permanent magnet, the residual magnetic induction strength, magnetic induction coercivity, the maximum magnetic energy product is very high, is the current magnetic performance of the best permanent magnet; 3. High cost performance.
AINiCo is composed primarily of Aluminum Nickel Cobalt and also Copper and Titanium. They are manufactured through either casting or sintering process. Cast AINiCo may be manufactured in complex shapes such as horseshoes not possible with other magnet materials. Sintered AINiCo offer slightly lower magnetic properties but better mechanical characteristics. it can be efficiently magnetized in any direction, and for anisotropic AINiComagnet, it generally has greater magnetic capacitive in a preferred orientation than isotropic types. AINiCo is hard and brittle, Machining or drilling cannot therefore be accomplished by ordinary methods. Holes are usually cored in at the foundry, and magnets are cast close to final size and then finish machined to closer tolerances. â?¢ Advantages of AlNiCo Magnet: 1.Customized designs are available. 2.Max working temperature can be as high as 550�°C. 3.Disadvantage: Br and BH(max)are not as high as rare earth magnet. 4.High energies and relatively low coercivity. 5.High magnetic flux density; low mold charge stable temperature properties; easy to shap.
