A) the zg sand pumps are designed for continuously handling the most difficult higher abrasive slurries Which contain too big solids to be pumped by a common pump. Such as dredging, suck gravel in the Dredger, suck gravel in the course of rivers or lakes, delivering slurries in mining, explosive sludge in Metal smelting.( type zgh pumps are of high-head ones ) B) zg dredge pumps are widely used to dredger and dam in the rivers, ports and wharf over our country, Such as changjiang river, huanghe river, liao river, and zhujiang delta. And also widely used Abraoad, such as middle east, Europe.
Sand Gravel Pumps are designed specifically for continuous pumping of extremely aggressive slurries, gavels, and sands. with a wide particle size distribution. Capable of handling large particles at consistently high efficiencies results in low cost of ownership. The large volume internal profile of the casing reduces associated velocities further increasing component life. Design Features: The unique segmented clamp ring on larger size units and solid on smaller pumps, facilitates casing rotation to any angle, reducing the need for costly high wearing bends. Minimal maintenance is required. Impeller expulsion vanes reduce gland pressure and intrusion of high concentrations of solids in the gland area. Efficiency is maintained by minimining suction side recirculation. Specially designed and shaped impeller vanes allow the handling of extraordinarily large particles. The unique casing design and sealing vanes prevent abrasive solids intrusion at the sealing faces. The large, robust casing has been designed to reduce internal velocities resulting in minimum efficiency loss and improved casing wear life. The casing is made up of three components to reduce maintenance time and costs associated with a onepiece design. (Except the 6/4 DG which has two components) heavy-duty grease lubricated taper roller bearing assemblies are fitted as standard. A rigid large diameter shaft with reduced overhang minimises deflection and vibration under all conditions ensuring trouble free operation. Unusually high service factors enable the assembly to carry all radial and axial thrusts. A unique -10 (dash 10) end cover assembly comprising of V-seals, double piston rings and an external flinger with grease lubricated labyrinths are standard with all warman pumps
¡¡4. Impeller type: non-clog (3/5vans) 5. Shaft sealing: packing/ mechanical ¡¡6. Wet parts material: a05, a07, steel 3) sand dredging pump general features: Xiyue brand xn sand dredging pumps are specially designed for dredge boat around river mud Delivering. It¡¯s single-stage, single-suction, centrifugal pumps with reliable structure and design. ¡¡¡¡1. Good structure design for marine using. ¡¡¡¡¡¡200xn-500xn series are single casing and 600xn-1000xn are two casing structure. ¡¡¡¡¡¡they both apply forward disassemble way and easy maintenance. According to the connection ¡¡¡¡¡¡with the pump working part, two structures can be offered: self-carrying bracket and pump ¡¡¡¡¡¡integrated with gearbox. The lubrication for the bracket is grease or thin oil. ¡¡¡¡2. Good dredging performance ¡¡¡¡¡¡good cavitations performance makes sure the pump high suction capacity and allows high ¡¡¡¡¡¡head and heavy concentration dredging. The impeller with width channel allows a large ¡¡¡¡¡¡flow and high head. ¡¡¡¡3. Good anti-abrasiveness pump wet parts ¡¡¡¡all wet parts are made by top anti-abrasive chromium alloy with good impact ¡¡¡¡ resistance and anti-abrasiveness. ¡¡¡¡4. Bearing seal type ¡¡¡¡¡¡200xn~500xn dredging pump apply mechanical sealing and packing seal. ¡¡¡¡¡¡600xn~1000xn dredging pump equipped with l-type spiral rubber seal which consist of 3 ¡¡¡¡¡¡l-ring of 1 sleeve to ensure the bearing sleeve water clean, it also equipped with sand ¡¡¡¡¡¡water separator. ¡¡¡¡ ¡¡¡¡ ¡¡¡¡ ¡¡¡¡ ¡¡¡¡ 4) sand dredging pump structure: ¡¡ ¡¡xiyue brand xn dredge pump is a new type of sludge pump researched & manufactured By our company basing on international g type gravel pumps, aiming at rivers and seas out Of repair. Xn pump is a single-stage single suction cantilever horizontal centrifugal pump with ¡¡advantages of light weight, good wear-resistant, super dredging performance, perfectly suited Wooden box
5. Shaft sealing: packing/gland packing & mechanical ¡¡6. Wet parts material: a05, a07, steel 3) gravel pump general features: ¡¡1. Xiyue brand xg sand gravel pumps are designed for continuous pumping of highly abrasive Slurries that containing large particles which the xh and xl series can't handle. ¡¡2. Xg sand gravel pumps are single casing structure, high efficiency, and wear resistant, wide flow Channel, good ability of npsh, stable performance, easy assembly, and the discharge ¡¡¡¡outlet can be adjusted at any directions. ¡¡3. They are suitable for delivering slurries in mining, explosive-sludge in metal melting, ¡¡¡¡dredging in dredger and course of rivers, sand reclamation ect. ¡¡¡¡ 4) gravel pump structure: ¡¡¡¡xiyue xg pumps are single casing connected by means of clamp bands and wide ¡¡¡¡wet-passage. The wet-parts are made of ni-hard and high chromium abrasion-resistance ¡¡¡¡alloys. The discharge direction of pump can be oriented in any direction of 360¡ã. ¡¡¡¡this type of pump possesses the advantages of easy installation and operation, good ¡¡¡¡performance of npsh and abrasion resistance. ¡¡¡¡ Material construction Impeller: high chrome alloy/steel Mechanical seal: carbon/ceramic/stainless steel Motor housing: alloy aluminum Shaft: carbon steel/stainless steel/high frequency wedding shaft Skype:allenfan83 Wooden box
Supplier: River Sand Suction Pump.
double tube hand pump for BIG SUP board TRIPLE ACTION it's more compact and light. It's the best for brands who want to use a pump of triple action as standard equipment in their SUP. The compact piston permits also females and young guys to be able to achieve easily high pressure. HP6, being used in TRIPLE-doublesingle action, can achieve 30psi rapidly and effortlessly. The switching 3-2-1 can be realized easily and comfortably rotating the switch knob. Itâ??s completely customizable for colour, graphic and calibration of gauge meter. Features: · capacity 3.2+3.2L, max. pressure 30psi as DIN EN 16051 · switch knob to change comfortably from triple to double or single seals and anti-sand filter for long life of pump and SUP extra long body and high-airflow piston for an easier inflation pump completely shock-proof, compact and light (1.7kg) · shockproof gauge meter
Monoblock pumps - Falcon centrifugal monoblock pumpsets are powered by a totally enclosed fan cooled AC induction two pole motor. Motor stator is made of low watt loss silicon steel laminations assembled under pressure and rigidly locked in the frame. The windings are of high-grade enameled copper wire offer excellent resistance and are varnish impregnated. Construction of motor frame and usage of quality materials result in high performance and low temperature rise thereby increasing the life cycle of the motor. salient features - High operating efficiency resulting in lower power consumption - Good suction lift characteristics - Inbuilt thermal overload protector in al single phase pumpsets upto 2.0 HP - Specially designed for wide voltage operation - Dynamically balanced rotating parts including rotor and impeller ensures minimum vibration and longer life - Back pull-out design for easy servicing and repair - Double shielded ball bearings, so no need of external lubrication - All Model fitted to Mechanical seal. specification - Power Range : 0.37Kw - 1.5 Kw (0.5 HP - 2.0 HP) - Version : Single Phase, 220-240V, 50Hz AC Supply Three Phase, 380-415V, 50Hz AC Supply - Speed : 2880 RPM - Maximum Total Head : 32 Mtr. - Maximum Flow Rate : 940 LPM - Maximum Suction Lift : 7 Mtr. - Degree of Protection : IP 44 - Class of Insulation : B0 - Maximum Ambient Tem. : 40 C - Sealing : Mechanical Seal - Type of Duty : S1 (Continuous) - Method of Starting : Permanent Split Capacitor (PSC) - Direction of Rotation : Three Phase, Electrically Reversible - Nominal Pumpset Size (Suction X Delivery in inch) : 25 X 25, 32 X 25, 40 X 32, 40 X 40, 50 X 40, 50 X 50, 65 X 50, 80 X 65, 80 X 80 (All size in mm) characteristics of clear cold water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5 Part Name Material Mechanical Seal : Carbon & Ceramic Motor Shaft : EN-8 Motor Body : FG-250 Bearing : SKF End Cover : FG-250 Bracket : FG-250 Flange : FG-250 Casing : FG-250 Impeller : FG-250 Cooling Fan : Plastic
Monoblock Pumps Falcon centrifugal monoblock pumpsets are powered by a totally enclosed fan cooled AC induction two pole motor. Motor stator is made of low watt loss silicon steel laminations assembled under pressure and rigidly locked in the frame. The windings are of high-grade enameled copper wire offer excellent resistance and are varnish impregnated. Construction of motor frame and usage of quality materials result in high performance and low temperature rise thereby increasing the life cycle of the motor. salient features High operating efficiency resulting in lower power consumption - Good suction lift characteristics - Specially designed for wide voltage operation. - Dynamically balanced rotating parts including rotor and impeller ensures minimum vibration and longer life. - Back pull-out design for easy servicing and repair. - Double shielded ball bearings, so no need of external lubrication. - Mechanical seal is provided as per customers requirement Specification - Power Range : 2.2 Kw - 11.2 Kw (3.0 HP - 15.0 HP) - Version : Three Phase, 380-415V, 50Hz AC Supply - Speed : 2880 RPM - Maximum Total Head : 65 Mtr. - Maximum Flow Rate : 1450 LPM - Maximum Suction Lift : 7 Mtr. - Degree of Protection : IP 44 - Class of Insulation : B0 - Maximum Ambient Tem. : 40 C - Sealing : Stuffing Box - Type of Duty : S1 (Continuous) - Direction of Rotation : Three Phase, Electrically Reversible - Nominal Pumpset Size (Suction X Delivery in inch) : 50 X 40, 50 X 50, 65 X 50, 80 X 65, 80 X 80 100 X 80 and 100 X 100 (All size in mm) Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 1.75 x 10 mÃ?/sec (max.) - Ph Value : 6.5 to 8.5 Material of construction - motor Part Name Material Gland Dori : Graphite String Motor Shaft : EN-19 with SS SLEEVE Motor Body : FG-250 Bearing : SKF End Cover : FG-250 Bracket : FG-250 Flange : FG-250 Casing : FG-250 Impeller : FG-250 Cooling Fan : Aluminium
Monoblock pumps Falcon centrifugal monoblock pumpsets are powered by a totally enclosed fan cooled AC induction two pole motor. Motor stator is made of low watt loss silicon steel laminations assembled under pressure and rigidly locked in the frame. The windings are of high-grade enameled copper wire offer excellent resistance and are varnish impregnated. Construction of motor frame and usage of quality materials result in high performance and low temperature rise thereby increasing the life cycle of the motor. Salient Features High operating efficiency resulting in lower power consumption. - Good suction lift characteristics. - Specially designed for wide voltage operation. - Dynamically balanced rotating parts including rotor and impeller ensures minimum vibration and longer life. - Back pull-out design for easy servicing and repair. - Double shielded ball bearings, so no need of external lubrication. specification - Power Range : 1.5 Kw - 5.5 Kw (2.0 HP - 7.5 HP) - Version : Three Phase, 380-415V, 50Hz AC Supply - Speed : 1440 RPM - Maximum Total Head : 12 Mtr. - Maximum Flow Rate : 3160 LPM - Maximum Suction Lift : 7 Mtr. - Degree of Protection : IP 44 - Class of Insulation : B0 - Maximum Ambient Tem. : 40 C - Sealing : Stuffing Box - Type of Duty : S1 (Continuous) - Direction of Rotation : Three Phase - Electrically Reversible - Nominal Pumpset Size (Suction X Delivery in inch) : 80 X 80, 100 X 100, 125 X 125, 150 X 150 (All size in mm) Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5 Part Name Material Gland Dori : Graphite String Motor Shaft : EN-19 with SS SLEEVE Motor Body : FG-250 Bearing : SKF End Cover : FG-250 Bracket : FG-250 Flange : FG-250 Casing : FG-250 Impeller : FG-250 Cooling Fan : Aluminum
