APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
They are used to connect precision tubing or pipe systems for fluid control, which makes them ideal for industries that require high levels of precision, accuracy & control. Instrumentation Tube Fittings are also commonly used for process instrumentation, analytical instrumentation, and process control equipment. SS Instrumentation Fittings are also known for their excellent mechanical properties, including high strength, toughness & resistance to corrosion fatigue. Stainless steel instrumentation fittings also have good high-temperature and pressure capabilities, making them ideal for use in many applications. We provide an extensive range of products, such as Alloy 20 Flanges, SMO 254 Forged Fittings and more. SS Compression Tube Fittings are essential in industries requiring high precision, accuracy & flow control levels. They offer superior corrosion resistance, durability, and reliability, making them a cost-effective solution for many applications. The high-quality stainless steel products we provide at Global Steel include Stainless Steel 304 Instrumentation Fittings, Stainless Steel 310 Instrumentation Fittings and more. Stainless steel instrumentation fittings are crafted through precision CNC machining, shaping, and thread creation. The chosen high-quality stainless steel, often 316 or 316L, undergoes processes like cold forming and surface treatment for corrosion resistance. Thorough quality control ensures dimensions, threads, and overall quality
Hastelloy Olets is a tungsten-added nickel molybdenum-chromium super alloy designed to survive corrosion in a variety of severe environments. In reducing conditions, nickel steel alloys with high nickel and molybdenum content resist pitting and crevice corrosion, while chromium gives resistance to oxidizing environments. Carbide precipitation is avoided during welding due to the low carbon concentration, ensuring corrosion resistance in as-welded structures. This nickel alloy is suitable for most chemical process applications because it resists the formation of grain boundary precipitates in the weld heat-affected zone when welded. Hastelloy C-22 is resistant to oxidizing acid chlorides, wet chlorine, formic and acetic acids, ferric and cupric chlorides, seawater, brine, and a wide range of mixed or contaminated organic and inorganic chemical solutions. This nickel alloy also has the best resistance to reducing and oxidizing conditions in process streams. Flue gas scrubbers, chlorination systems, sulfur dioxide scrubbers, pulp, and paper bleach plants, pickling systems, and nuclear fuel reprocessing are all examples of the chemical process business. Acid production, pharmaceutical industries, cellphone manufacture, chlorination systems, pesticide production, incinerator scrubber systems, wastewater treatment, pollution control stack liners, ducts, dampers, scrubbers, stack-gas, reheaters, fans, fan housings, flue gas desulfurization systems heat exchangers, reaction vessels, evaporators, and transfer pipes are examples of chemical processing components.
Hastelloy Olets is a tungsten-added nickel-molybdenum-chromium super alloy designed to survive corrosion in a variety of severe environments. In reducing conditions, nickel steel alloys with high nickel and molybdenum content resist pitting and crevice corrosion, while chromium gives resistance to oxidizing environments. Carbide precipitation is avoided during welding due to the low carbon concentration, ensuring corrosion resistance in as-welded structures. This nickel alloy is suitable for most chemical process applications because it resists the formation of grain boundary precipitates in the weld heat-affected zone when welded. Hastelloy C-22 is resistant to oxidizing acid chlorides, wet chlorine, formic and acetic acids, ferric and cupric chlorides, seawater, brine, and a wide range of mixed or contaminated organic and inorganic chemical solutions. This nickel alloy also has the best resistance to reducing and oxidizing conditions in process streams. Flue gas scrubbers, chlorination systems, sulfur dioxide scrubbers, pulp, and paper bleach plants, pickling systems, and nuclear fuel reprocessing are all examples of the chemical process business. Acid production, pharmaceutical industries, cellphone manufacture, chlorination systems, pesticide production, incinerator scrubber systems, wastewater treatment, pollution control stack liners, ducts, dampers, scrubbers, stack-gas, reheaters, fans, fan housings, flue gas desulfurization systems heat exchangers, reaction vessels, evaporators, and transfer pipes are examples of chemical processing components
Product Name : Stainless Steel Angle Surface : Sandblasting, solution, pickling Edge : Plain Mill Standard : ASTM DIN GB JIS EN AISI 1 Stainless steel angle steel is widely used in the construction layout, as well as in various engineering layouts, such as the construction of beams, and has a significant effect in the construction of engineering equipment. 2. When used, stainless steel angle steel has comparative weldability, strong plasticity and deformation, and also has certain mechanical strength. 3. The corrosion resistance of stainless steel angle steel is relatively high, and it has good corrosion resistance in the production process of pulp and paper. Moreover, stainless steel is also resistant to the corrosion of ocean and corrosive industrial atmosphere. 4. Stainless steel angle steel can be used as equipment for dry pulp and paper making, heat exchanger, dyeing equipment, film processing equipment, pipes, and materials for the exterior of buildings in coastal areas. 5. Precipitation hardening stainless steel angle steel is a steel that can precipitate carbides in the steel by means of heat treatment, so as to improve the strength. 6. Martensitic stainless steel angle steel is a kind of steel whose properties can be adjusted by means of heat treatment. Its strength and hardness are high and it is very useful in technology and mechanics. Application field * The company adheres to the corporate spirit of never being satisfied and striving to surpass, and continuously creates new brilliance with the new economic concept of continuous innovation. Reward guests and friends from all over the world with satisfactory service. Our company is willing to cooperate closely with friends from all walks of life at home and abroad, and work together to create a better tomorrow. Warehouse Storage * Shandong Jintuo Metal Materials Co., Ltd is located in Liaocheng City, the capital of steel tubes. It is a large enterprise specializing in the sales of carbon steel, stainless steel, galvanized color coated products, and copper and aluminum.Our company adopts a flexible business approach and management mechanism to provide good services to customers, while also considering the interests of the owner and the project, in order to ensure the quality of the project. Packing and shipping * Our products are exported to multiple overseas countries and regions such as Europe, America, South Asia, Southeast Asia, Africa, and Latin America, and have won the trust and support of customers with excellent quality and service. * During the supply process, the company can timely use sufficient funds to adjust the production variety and model of the steel plant, ensuring the use needs during the peak construction period.
At A.S Engineers & Fabricators, excellence is not just a goal; it's our commitment. With a steadfast dedication to providing unparalleled solutions for marine construction, we stand as pioneers in the industry. Backed by years of experience and a wealth of expertise, we have earned a reputation for delivering top-notch products and services that exceed expectations. Our mission is simple yet profound: to revolutionize the marine construction industry with innovative solutions that prioritize quality, reliability, and sustainability. Every project we undertake is driven by a passion for excellence and a relentless pursuit of customer satisfaction. Robust Construction Our Heavy Structure Column - Marine is built with durability in mind, ensuring it can withstand the harsh marine environment without compromising on strength Customizable Options We understand that every project has unique requirements. That's why our Heavy Structure Column - Marine is available in various sizes and configurations, allowing for customization to suit specific project needs. Corrosion Resistance Made from high-quality materials and treated with corrosion-resistant coatings, our columns offer long-lasting protection against saltwater and other corrosive elements Exceptional Stability With a focus on structural integrity, our columns provide exceptional stability, ensuring the safety of marine structures even in challenging conditions Easy Installation Designed for hassle-free installation, our columns come with user-friendly features, reducing downtime and labor costs during marine construction projects Cost-Effective Solution Investing in our Heavy Structure Column - Marine means investing in a cost-effective solution. Its longevity and low maintenance requirements make it a smart choice for marine construction projects, saving both time and money in the long run
Supplier: Coir bricks, fresh vegetables , fish, chicken, black paper, ceylon tea, tiles
Services: Agent and out sourcing
SIZE : 1/8" to 4" (As Per Customer Requirement) DIMENSION STANDARD : ANSI B 16.9 ,B 16.25 , B 16.28,MSS SP-43,SP-48,SP59 SCHEDULE: SCH 10, SCH 40, STD, SCH30, SCH80, SCH XS, SCH 80, SCH 60, SCH120, SCH140, SCH160, XXS TYPE : Seamless FORM :Pipe Nipple, Hex Nipple, Swage Nipple, Barrel Nipple MATERIAL GRADE : Carbon Steel Buttweld Nipple: ASTM A 234 WPB, WPBW, WPHY 42, WPHY 46, WPHY 52, WPH 60, WPHY 65 & WPHY 70 Stainless Steel Buttweld Nipple: ASTM A403 WP Gr. 304, 304H, 309, 310, 316, 316L, 317L, 321, 347, 904L Alloy Steel Buttweld Nipple: ASTM / ASME A/SA 234 Gr. WP 1, WP 5, WP 9, WP 11, WP 12, WP 22, WP 91 Duplex Steel Buttweld Nipple: ASTM A 815 UNS NO S 31803, S 32205 Low Temperature Carbon Steel Buttweld Nipple: ASTM A420 WPL3 / A420WPL6 Nickel Alloys Buttweld Nipple: Standard ASTM / ASME SB 336 UNS 10276 (Hastelloy C 276) UNS 2200 (NICKEL 200) UNS 2201 (NICKEL 201) UNS 4400 (MONEL 400) UNS 8020 (ALLOY 20) UNS 8825 Inconel (825) UNS 6600 (Inconel 600) UNS 6601 (Inconel 601) UNS 6625 (Inconel 625)
We have in store for our clients a sturdy range of stainless steel Grade 321 Pipes, Stainless steel Grade 316L pipes, Stainless steel grade 904L Pipes, that are capacitated to withstand temperature variations and thus are used in heat transfer process equipment like boilers, super heaters, heat exchangers, condensers and similar applications. Size : ½" to 24" in Seamless & upto 60" in Welded. (As Per Customer Requirement) Schedule : Sch 5s To Sch 160 Stainless Steel Grade : ASTM / ASME SA 312 GR. TP 304, 304L, 304H, 309S, 309H, 310S, 310H, 316, 316TI, 316H, 316L, 317, 317L, 321, 321H, 347, 347H, 904L. ASTM / ASME SA 358 CL 1 & CL 3 GR. 304, 304L, 304H, 309, 310S, 316, 316H, 321, 347. DUPLEX STEEL GRADE : ASTM / ASME SA 790 UNS NO S 31803, S 32205 Specifications : ASTM A/ASME SA213/A249/A269/A312/A358 CL. I to V ASTM A789/A790.
