Organic Waste Composter machine with heater . from 50 kg to 1000 kg per day capacity. fully automatic.
Product introduction: 1. The crawler type compost turner belongs to the ground pile fermentation mode, which is the most economical mode of saving soil and human resources at present. 2. The material needs to be piled up into a stack, then the material is stirred and crushed at regular intervals by the turning machine, and the decomposition of organic matter will be under aerobic conditions. 3. It also has a broken function, which greatly saves time and labor force, making the production efficiency and product quality of the organic fertilizer plant improved significantly, and the cost reduced greatly. 4. When the turning machine works, the sludge, sticky chicken manure and other materials can be well stirred with the fungus and straw powder, creating a better aerobic environment for the fermentation of materials. 5. It not only ferments faster than deep groove type, but also effectively prevents the production of harmful and odorous gases such as hydrogen sulfide, amine gas and indole during fermentation, which is in line with environmental production requirements. Performance characteristics: Tongda crawler type compost turner has the following characteristics: 1. The operation is easier and the hydraulic directional type was eliminated; save the site, artificial, diesel, shorten the working time, advanced the fermentation cycle. 2. This product has been turned over and separated by soft start. (The other domestic products of the same kind use iron for iron hard clutch, which has a serious damage to the chain, bearing and shaft). 3. Installed front hydraulic push plat, so it is no need to manually take the whole pile. 4. Cylinder hydraulic lifting. Working principle: 1. The bio-organic manure turning machine is a bio-organic fertilizer made of livestock and poultry manure, agricultural waste, sugar mill filter sludge, sludge, domestic garbage, etc. through the principle of oxygen-consuming fermentation to make it green and environmentally friendly and improve the soil quality. 2. It can reach one day of heating, 3-5 days of deodorization, sterilization (can completely kill insects and eggs in feces, etc.), and fertilizer is made in 7 days. 3. It is faster and more efficient than other Mechanical methods of fermentation. 4. According to customer requirements can also add some auxiliary facilities, such as automatic sprinklers, etc.
length 4300 mm net, width 2300 mm, height 2300 mm hook-and-wire systems refrigeration floor heating Composting is a biological process in which micro-organisms, mainly bacteria and fungi convert organic matter into compost. This natural process of complex organic matter breaking down into simpler elements is called decomposition; which results in a dark earthy sweet smelling nutrient rich humus high in carbon and nitrogen called compost. Compost is an excellent medium for growing plants that recycles nutrients back to enrich the soil. We manufacture COMMUNITY (for Municipalities,Hotels, Restaurant, Schools, etc.) and for INDUSTRY (foodindustry for example).
Product introduction: 1. The crawler type compost turner belongs to the ground pile fermentation mode, which is the most economical mode of saving soil and human resources at present. 2. The material needs to be piled up into a stack, then the material is stirred and crushed at regular intervals by the turning machine, and the decomposition of organic matter will be under aerobic conditions. 3. It also has a broken function, which greatly saves time and labor force, making the production efficiency and product quality of the organic fertilizer plant improved significantly, and the cost reduced greatly. 4. When the turning machine works, the sludge, sticky chicken manure and other materials can be well stirred with the fungus and straw powder, creating a better aerobic environment for the fermentation of materials. 5. It not only ferments faster than deep groove type, but also effectively prevents the production of harmful and odorous gases such as hydrogen sulfide, amine gas and indole during fermentation, which is in line with environmental production requirements. Performance characteristics: Tongda crawler type compost turner has the following characteristics: 1. The operation is easier and the hydraulic directional type was eliminated; save the site, artificial, diesel, shorten the working time, advanced the fermentation cycle. 2. This product has been turned over and separated by soft start. (The other domestic products of the same kind use iron for iron hard clutch, which has a serious damage to the chain, bearing and shaft). 3. Installed front hydraulic push plat, so it is no need to manually take the whole pile. 4. Cylinder hydraulic lifting. Working principle: 1. The bio-organic manure turning machine is a bio-organic fertilizer made of livestock and poultry manure, agricultural waste, sugar mill filter sludge, sludge, domestic garbage, etc. through the principle of oxygen-consuming fermentation to make it green and environmentally friendly and improve the soil quality. 2. It can reach one day of heating, 3-5 days of deodorization, sterilization (can completely kill insects and eggs in feces, etc.), and fertilizer is made in 7 days. 3. It is faster and more efficient than other Mechanical methods of fermentation. 4. According to customer requirements can also add some auxiliary facilities, such as automatic sprinklers, etc.
Product Information: The groove type compost turner are also called as rail type compost turner, which is usually used in the fermentation and turning of the poultry manure, sludge and garbage, filter mud, sugar dregs cake, straw sawdust and other organic waste. It is widely used in the fermentation and compost job of organic fertilizer plant, compound fertilizer plant, sludge and waste treatment plant, garden spot, agaricus bisporus growing plant, etc,. Features: 1.Automation control. Centralized control by the control cabinet, so that can realize the function of manual or automatic control. 2.Solid and durable. The teeth are durable and has the ability of breaking and mixing the compost materials. 3.The groove type compost turner is suitable for aerobic fermentation, and it can match with solar energy fermentation chamber, fermentation tank and transfer machine. 4.Compact structure and advanced technology. The use of some beneficial microorganisms can promote the rapid decomposition of organic wastes such as livestock manure. Turning over the heap machine fermentation production of biological organic fertilizer process: 1. The ground stack, with the ground stack machine, or with aerobic tank type fermentation machine, in the fermentation tank according to the proportion of the other organic matter and bacteria 2. Evenly sprinkle the fungus agent, turn over the heap fermentation to heat up, smelly, decomposing, killing the mixed fungus grass seeds 3. Ferment for 7-12 days, according to the temperature of different places turn over the number of times is not the same 4. Completely fermented and cooked, out of the pool (the ground type is directly collected by forklift) 5. With a screening machine for thickness screening, (screening good powder fertilizer can be sold directly) 6. The screened out large pieces with the pulverizer after crushing back to the screening machine 7. Use premixed machine to mix the required trace elements 8. Use granulator to granulate 9. Into the dryer and cooling machine 10. Automatic packaging machine packaging for sale
Supplier: Shredder machine and composting machine.
Product overview 1.The device is a kind of desktop CNC plasma cutting machine featuring high speed, precision cutting and small size. 2.The desktop CNC plasma cutting machine is specially designed for the rapid plasma cutting of carbon steel plates, aluminum plates, copper plates, stainless steel plates and other metal plates in any graphic. Under normal circumstances, the cutting plane does not need secondary processing, and the cutting effect is good, without dross and burrs. 3.The desktop plasma cutting machine can replace punch for processing and is characterized with high degree of automation, high reliability, high accuracy, low price, easy operation and maintenance, etc. The product is particularly suitable for medium and thin non-ferrous metal plates. 4.Desktop CNC plasma cutting machine is extensively used in machinery manufacturing, auto parts, hardware, sports equipment, advertising and other industries, with a high cost performance. Application Materials Galvanized sheets, white sheets, titanium olate, carbon steel, stainless steel, alloy steel, composte metal. Application Industries This machine can be used in ship building,construction equipment, transport equipment, aerospace industry, bridge building, military industry, wind power, structural steel, boiler containes making, agriculture machinery, chassis electrical cabinets, elevator manufacturing, textile machinery and environmental protection equipment etc. Feature 1. CNC plasma cutter machine adopts light-weight structural design, the structure has good rigidity, light weight and small motion inertia. 2.Desktop structure. Y axis adopts synchronous double-motor and driver, and X,Y,Z axises adopt linear guideways, stable transmission and high operational precision. 3.Mainly cut Three-dimensional LED advertising word, metal plates with groove characters and baseboards, and cutting accuracy lives up to excellent index. 4.Small cutting holes, tidiness and no-residue phenomenon, avoids shaping process at second time. 5.Fast cutting speed, high precision and low cost.CNC system with high configuration, automatic arc strike and stable performance, with above 99% arc strike success rate. 6.Support for standard G code path files which are generated by softwares such as Artcut, Artcam, Type3. DXF format files generated by softwares such as AUTOCAD can also be read through software transform. The controlling system adopts U disk to exchange processing files, operation is convenient and speedy. 7.Plasma power source and burning torch are equipped with famous domestic brands. and they are manufactured by factories with multi-termed national patent technology. 8.Training video available air plasma cutting machine , plasma cutting machine , cnc plasma power source. Technical parameter 1 Cutting shape any shapes 2 LCD Display Dimension 7.0 Inches 3 Effective Cutting Width (X axis) 1250mm 4 Effective Cutting Length (Y axis) 2500mm 5 Cross Beam Length 1500mm 6 Longitudinal Rail Length 3000mm 7 Cutting Speed 0-8000mm per minute 8 Plasma Cutting Thickness 2--20mm ( Depends on plasma power source capacity) 9 lifting body 1set 10 Drive Mode bilateral drive 11 Cutting Mode plasma 12 Ignition device Auto ignition device 13 Height regulating device Arc voltage height 14 File transmission USB transmission 15 Nesting software Fastcam standard 16 File transmission USB 17 LCD Display Dimension 7" 18 Plasma Power Source Ruiduncnc 45/85/105/120/200A 19 Plasma Air Only pressed Air 20 >Plasma Air Pressure Max. 0.8Mpa 21 Cutting precision 0.5mm National standard JB/T10045.3-99 22 Control accuracy 0.01mm 23 Power Supply Voltage/Frequency 380V 50HZ 24 Rated Power Supply 1000W 25 Working Temperature >-10C-60C. Relative Humidity, 0-95%. wooden package
Supplier: Thanjavur paintings, vermy compost, cotton sarees, cotton dhoties, cotton towels (thundu), CNC Machined components, heavy duty universal drilling machine
Hydraulic lane compost turner uses hydraulic system to control the lifting of turning device, which saves labor and prolongs the machines service life. The turner is designed according to the aerobic fermentation technology. It can mix the materials evenly, providing better aerobic environment for fermentation. Equipped with a control cabinet, lane type compost turning machine can be controlled both manually and automatically.
