Epoxy Finish Paint is two-component, polyamide adduct cured, General Purpose Air drying Epoxy Coating. Its Excellent substitute to Enamel.
DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.
Specifications 1.odorless 2.low VOC 3.antimicrobial 4. mildew resistant 5.environmentally friendly 6.waterproof 7.Scrub resistance Description It is an enhanced mildew proof product adopting nano-scale Ag+ antimicrobial and mildew proof technology, integrating odorless formula, with fresh product smell, smooth paint film, durable and beautiful paint.As an affordable and environmentally friendly product with excellent decorative performance, it is characterized by fresh smell, environmental health, strong covering power, large painting area, convenient constructionapplication, short constructionapplication period, etc. Specification Data Solvent: Water Pigment: Non-lead pigment Theoretical Solids By Volume: more than 50% Theoretical Coverage: Theoretically 1 litre of this product covers 12 sqm in 1 coat Coverage varies considerably depending on application methods and surface roughness and porosity. Shelf Life: Minimum 12 months at 77F(25C) unopened and store in cool and dry places. Recommended Film Thickness: Wet: 80 micron Dry: 30 micron Dry Time: At 77F (25C) and 50% R.H. to recoat Touch Dry: 1 hours Recoat : 2-3 hours Application: Brush, Roll, conventional spray or Airless Spray. Thinner: Thin up 15% depend on different application methods & temperature. Do not over thin by adding more than 30% water. Brush or Roller: For sealing new or bare surfaces thin with up to 1 part of clean water to 5-10 parts of paint(10%-20%) Conventional Spray: Add up to 1 part clean water to 5 parts paint(20%) Airless spray: do not thin Clean-up: Clean up equipment with water Typical painting system Substrate System All kinds of Wall surfaces 1.Alkali Resistance Primer (1 coat) 2.Emulsion Wall Paint (2 coats)
Supplier: Chemical, chemical raw material, auxiliaries, solvents, paint, coating, rubber, plastic, plasticizer, surfactant, additives, steel pipe, steel tube, stainless steel tube, stainless steel pipe, pipe fitting, flange, fasteners, steel wire, steel accessories
Services: Transportation agent,customs clearance service,
Buyer: Import chemical raw materials, auxiliaries, bulk commodities
We supply balustrade and its related components like connectors, saddles, pipes end caps in SS201, SS304, SS316, SS316L. Pipes OD42.2mm*2mm. Also available other OD on request. Balustrade shape round, square any other custom designed shape. Height about 1060mm. Finish: satin, Glossy.
Product Description: We supply connector in SS201, SS304, SS316, SS316L suitable for pipes OD42.2mm*2mm. Also available other OD on requist. Connectors in round, square any other custom designed shape. Finish: satin, Glossy.
Indian Granite: We can supply Premium Grade to commercial grade. Size and surface and sides finishes can be customized. Finishes: Mirror, Matte, Flame finish etc. Slabs: Length- 6’ to 9’, width: 2’ to 3’, thickness:18mm (+/-1) Tiles: 45x45cm, 60x45,x60x60cm in 10mm. Any other sizes can be customize. Edge finish as per your requirement. Surface finish: we have automated polishing and Semi Automated polishing. 1. Indian Granite-Black 2. Indian Granite-Black Galaxy 3. Indian Granite-Black Pear 4. Indian Granite-Coffee Brown 5. Indian Granite-Coral Gold 6. Indian Granite-Jasemine White 7. Indian Granite-River White 8. Indian Granite-Sappahire Blue 9. Indian Granite-Silver Waves 10. Indian Granite-Steel Grey 11. Indian Granite-Tan Brown 12. Indian Viscon White 13. Indian Granit-Aspen White
Indian Granites: Indian Granite: We can supply Premium Grade to commercial grade. Size and surface and sides finishes can be customized. Finishes: Mirror, Matte, Flame finish etc. Slabs: Length- 6’ to 9’, width: 2’ to 3’, thickness:18mm (+/-1) Tiles: 45x45cm, 60x45,x60x60cm in 10mm. Any other sizes can be customize. Edge finish as per your requirement. Surface finish: we have automated polishing and Semi Automated polishing. 1. Indian Granite-Black 2. Indian Granite-Black Galaxy 3. Indian Granite-Black Pear 4. Indian Granite-Coffee Brown 5. Indian Granite-Coral Gold 6. Indian Granite-Jasemine White 7. Indian Granite-River White 8. Indian Granite-Sappahire Blue 9. Indian Granite-Silver Waves 10. Indian Granite-Steel Grey 11. Indian Granite-Tan Brown 12. Indian Viscon White 13. Indian Granit-Aspen White
Indian Granite Black: We can supply Premium Grade to commercial grade. Size and surface and sides finishes can be customized. Finishes: Mirror, Matte, Flame finish etc. Slabs: Length- 6’ to 9’, width: 2’ to 3’, thickness:18mm (+/-1) Tiles: 45x45cm, 60x45,x60x60cm in 10mm. Any other sizes can be customize. Edge finish as per your requirement. Surface finish: we have automated polishing and Semi Automated polishing.
Indian Granite Black Galaxy: We can supply Premium Grade to commercial grade. Size and surface and sides finishes can be customized. Finishes: Mirror, Matte, Flame finish etc. Slabs: Length- 6’ to 9’, width: 2’ to 3’, thickness:18mm (+/-1) Tiles: 45x45cm, 60x45,x60x60cm in 10mm. Any other sizes can be customize. Edge finish as per your requirement. Surface finish: we have automated polishing and Semi Automated polishing.
