Part No. 20BYGH408Single Shaft Frame Size:  NEMA8 Step Angle:  1.8 degree Voltage:  4.32VDC Current: 0.8A/phase Resistance: 5.4Ohm/phase Inductance:  1.5mH/phase Holding torque:  30Kg-cm Rotor inertia: 3.6  g-cm2 Detent torque: 5� kg-cm Number of wire leads:  4 Weight:  0.2KG Length:40mm Front  shaft diameter: 4mm Front shaft length: 20mm round shaft This model is for Single shaft, with 4mm motor shaft, 20mm front shaft length, round shaft! More Order Quantites, more  discount!
Part No.:  20BYGH206  Single Shaft Frame Size: NEMA8 Step Angle:  1.8 degree Voltage:  1.92VDC Current:  0.6A/phase Resistance:  3.2 Ohm/phase Inductance:  0.9  mH/phase Holding torque 14Kg-cm Rotor inertia  9  g-cm2 Detent torque: 2 kg-cm Number of wire leads  4 Weight:  0.05KG Length:28mm Front  shaft  diameter: 4mm (1/4'') Front shaft length:  20mm round shaft This model is for Single shaft, with 4mm motor shaft, 20mm front shaft length, round shaft!
Part No.  39BYG003Single Shaft Frame Size NEMA16 Step Angle:  1.8 degree Voltage:  12VDC Current:  0.48A/phase Resistance:  25Ohm/phase Inductance  22mH/phase Holding torque:  100Kg-cm Rotor inertia:� � � 11g-cm2 Detent torque:� � � 5kg-cm Number of wire leads:� 4 Weight:� � � 0.12KG Length:20mm Front� shaft� diameter: 5mm Front shaft length:� � 24mm round shaft This model is for Single shaft, with 5mm motor shaft, 24mm front shaft length, round shaft! More Order Quantites, more  discount!
Part No.: 28BYGH102Single Shaft Frame Size:NEMA11 Step Angle: 1.8 degree Voltage: 3.8VDC Current: 0.67A/phase Resistance: 5.6Ohm/phase Inductance: 3.4mH/phase Holding torque: 60Kg-cm Rotor inertia: 9g-cm2 Detent torque:� 4kg-cm Number of wire leads: 4 Weight: 0.11KG Length:32mm Front shaft diameter: 5mm Front shaft length: 20mm round shaft This model is for Single shaft, with 5mm motor shaft, 20mm front shaft length, round shaft More Order Quantites, more discount
Part No.:  20BYGH202  Single Shaft Frame Size:  NEMA8 Step Angle:  1.8 degree Voltage:  4.6VDC Current:  0.2 /phase Resistance:  23 Ohm/phase Inductance:  8.2  mH/phase Holding torque:  14Kg-cm Rotor inertia:   9 g-cm2 Detent torque:    2 kg-cm Number of wire leads: 4 Weight:   0.05KG Length:   28mm Front shaft diameter: 4mm (1/4'') Front shaft length:  20mm round shaft This model is for Single shaft, with 4mm motor shaft, 20mm front shaft length, round shaft! More Order Quantites, more discount!
Introduction The d2hb882mb is an economical microstepping driver based on patented technology of longs motor.It is suitable for driving 2-phase 4-phase hybrid stepping motors .By using the advanced bipolar constant-current shopping technique , it can output more speed and torque from the same motor, compared with traditional drivers , such as l/r drivers .Its 3-state current control technology allows coil currents to be well controlled and with relatively small current ripple, therefore less motor heating is achieved. Features Low cost and good high-speed torque 14 selectable resolutions Supply voltage up to +80vdc Suitable for-2-phase and 4-phase motors Output current up to 5.86a Dip switch current setting 8different values Optically isolated input signals Pulse frequency up to 200khz Automatic idle-current reduction Small size (107*97*48), weight:1kg
Introduction The d2hb542ma is an economical microstepping driver based on patented technology of longs motor.It is suitable for driving 2-phase 4-phase hybrid stepping motors .By using the advanced bipolar constant-current shopping technique , it can output more speed and torque from the same motor, compared with traditional drivers , such as l/r drivers .Its 3-state current control technology allows coil currents to be well controlled and with relatively small current ripple, therefore less motor heating is achieved. Features Low cost and good high-speed torque Supply voltage up to +45vdc Output current up to 5.86a Optically isolated input signals Automatic idle-current reduction 14 selectable resolutions Suitable for-2-phase and 4-phase motors Dip switch current setting 8 different values Pulse frequency up to 200khz Dip switch current setting 8 different values Small size (122.2*90*33), weight:0.3kg
Features: Model: 86blf01; 86blf02; 86blf03; 86blf04 Number of poles: 8 Number of phases: 3 Nominal voltage vdc: 48 Rated speed rpm: 3000 Continuous torque n-m: 0.35~1.4 Output power watts: 110~440 Peak torque1 n-m: 1.05~4.2 Peak current amps: 10.8~38.0 Line to line resistance ohms: 0.47~3.2 Line to line inductance mh: 0.71~2.1 Torque constant n-m/amps: 0.11~0.115 Back emf v/krpm: 11.5~12.0 Rotor inertia gòcm2: 350~1250 Body length (l) mm: 57~94 Mass kg: 1.1~2.75
Features: Modelú¦pm25s-048-01ú+pm25s-048-02ú+pm25s-048-02bú+pm25s-048-03aú+pm25s-048-09ú+pm25s-048-10ú+pm25s-048-11ú+pm25s-048-15ú+pm25s-048-17ú+pm25s-048-19ú+pm25s-024-01ú+pm25s-024-02ú+pm25s-024-03ú+pm25s-024-04ú+pm25s-024-05ú+pm25s-024-09ú+pm25s-024-12ú+pm25s-024-14 Step angel ( íp) 7.5~15 No. Of phaseú¦ 2/4 Rate voltage (v): 5~24 Rate current (a): 0.1~1.3 Phase resistance ( ª+ ): 5~120 Phase inductance (mh): 1.5~31 Holding torque (g.Cm): 100~230 Detent torque: 45~60
Features: Modelú¦ 17hm201ú+ 17hm206ú+ 17hm208ú+ 17hm602ú+ 17hm604ú+ 17hm607ú+ 17hm805ú+ 17hm809ú+ 17hm810 Step angel ( íp): 0.9 Motor length l(mm): 34~48 Rate voltage (v): 2.4~11.2 Rate current (a): 0.4~2.4 Phase resistance ( ª+ ): 1~28 Phase inductance (mh): 1.8~30 Holding torque (g.Cm): 1400~4800 Lead wire (no.): 4/6 Rotor inertia (g. C¬o): 34~68 Detent torque (g.Cm): 180~260 Motor weight (kg): 0.2~0.34
