Pod Logistics

D6 is also be known as Residual Fuel Oil and is of high-viscosity. This particular fuel oil requires preheating to 220 - 260 Degrees Fahrenheit. D6 is mostly used for generators. D6 is a type of residual fuel, mainly used in power plants and larger ships. The fuel requires to be preheated before it can be used. It is not possible to use it in smaller engines or vessels/vehicles where it is not possible to pre-heat it. D6 is its name in the USA. In other parts of the world it has other names. Residual means the material remaining after the more valuable cuts of crude oil have boiled off. The residue may contain various undesirable impurities including 2 percent water and one-half percent mineral soil. D6 fuel is also known as residual fuel oil (RFO), by the Navy specification of Bunker C, or by the Pacific Specification of PS-400 Recent changes in fuel quality regulation now require further refining of the D6 in order to remove the sulfur, which leads to a higher cost. Despite this recent change, D6 is still less useful because of its viscosity as well as that it needs to be pre-heated before it can be used and contains high amounts of pollutants, such as sulfur. Since it requires pre-heating, it cannot be used in small ships or boats or cars. However large ships and power plants can use the residual fuel oil. The price of D6 diesel traditionally rises during colder months as demand for heating oil rises, which is refined in much the same way.In many parts of the United States and throughout the United Kingdom and Australia, d6 diesel may be priced higher than petrol. D6 Diesel Standards and ClassificationCCAI and CII are two indexes which describe the ignition quality of residual fuel oil, and CCAI is especially often calculated for marine fuels.

We supply high-quality petroleum products from trusted Middle Eastern, European, and Turkish producers, ensuring compliance with international standards. Important Notice: Due to widespread fraud in the oil industry, our procedures are non-negotiable. No upfront payment is required. TTM (Table-Top Meeting) can be arranged before LC for qualified buyers with ICPO + POF. Key Products & Origins: Diesel (D2, D6) Origin: Middle East EN590 Origin: Italy, Europe, Turkiye, Middle East Jet Fuel (Jet A1) Origin: Middle East Our UAE office is a licensed petroleum exporter, ensuring seamless transactions and full regulatory compliance. Sales & Purchase Procedure: Request: Buyer submits Letter of Interest + Proof of Funds (POF) (Bank Statement, BCL, etc.). Introduction: Seller verifies the buyer and conducts an introductory call. Capability Assessment: Seller assesses the buyer's financial capacity. Corporate Offer: Seller issues a Formal Corporate Offer (FCO) with prices, volume, and terms. Sales Agreement: Buyer & Seller finalize a Sales & Purchase Agreement (SPA). The seller also issues an MFPA (Master Fee Protection Agreement) for agents/mandates. Banking & Collateral: Buyer submits SBLC MT760, and Seller provides a 2% Performance Bond. Loading & Documentation: Seller loads the vessel at their own cost and issues delivery documents (B/L, Ullage Report, COO, Q88, etc.). Delivery & Payment: Buyer conducts a Dip Test, completes an MT103 wire transfer, and receives Title of Ownership upon payment. We ensure reliable supply, competitive pricing, and seamless transactions for our global buyers.

We can connect you with our friend end sellers/title holders to offer express work with petroleum products of Russian or non-Russian origin, where they can provide reliable and serious offers. Please contact us only if you are the real end buyer or his direct mandate. The products list: - Diesel EN590 - JET FUEL A1, JP 54 - VIRGIN D6 FUEL OIL - LPG, LNG - AGO Automotive Gas Oil - Gasoline Octane 72, 76, 91, 93, 95

MOQ: 10,000 Barrels per Month Supply Ability: 1,000,000 Barrels per Month JP54 Technical Specifications: ADDITIVES Antioxidant in hydro processed fuel mg/l min 17 max 24 Antioxidant non hydro processed fuel mg/l max 24 Static dissipater first doping ASA- 3 mg/l max 1 Stadis 450 mg/l max 3 COMBUSTION PROPERTIES Specific energy, net mi/kg min 18.4 D 4808 Smoke point mm min 19 D 1322 Lumininomitter number min 45 D 1740 Naphtales % vol max 3 D 1840 Propriety unit min max result test ip method ASTM COMPOSITION Total acidity mg KOH /g max 0.01 354 D 3242 Aromatic % vol max 22.0 158 D 1318 Sulphur, total % mass max 0.30 107 D 1266/2622 Sulphur mercaptan % mass max 0.003 342 D 3227 Doctor test 30 D 4952 VOLATILITY Initial boiling point centigrade max report 123 D 96 10% vol at C 240 20% vol at C report 50% vol at C report 80% vol at C report End point centigrade max 42 170/303 D 56 / 3828 Density at 15 C kg m2 min /max 776/840 180/385 D 1298 LOW TEMPERATURES PROPERTIES freezing point centigrade max 40 15 D 1298 Corrosion copper (2hrs at 100 C) Corrosion silver (4 hrs at 500C) max 1 227 STABILITY Thermal stability control temp. 280C 323 Filter pressure, differential mm. Hg max 25 Tube deposit rating (visual) max

TTT procedure: EN590 10pm price $460/MT, Jet fuel A1 price $76/BBL (1) FREE ON-BOARD TRANSACTION PROCEDURE - (TANK TO TANK). Rotterdam, Houston, Fujairah, Jurong, Ningbo-Zhoushan 1. Buyer issues an official ICPO with the seller's procedure, passport copy, banking details along with their Tank Storage Agreement "TSA". 2. Seller issues their Commercial Invoice "CI" to the buyer, Buyer signs and returns the commercial invoice to the seller along with an Acceptance Letter of the sales and purchase procedure. 3. Seller verifies the buyer's storage facility and their Tank Storage Agreement (TSA) with the port authority. (NB: Seller will issue a Tank-to-Tank Injection Agreement (TTIA) to be signed by all parties only if buyer's TSA is engaged, not active or cannot be verified with the local port authority). 4. Seller issues all POP documents below to the buyer upon a successful verification and approval of the buyer TSA or after receiving the TTIA fully signed by all parties: a. Injection Report. b. Product Passport. c. 24 Hours SGS Report. d. Product Certificate of Origin. e. Tank Storage Receipt (TSR). f. Authorization to sell and collect. g. Unconditional Dip-Test Authorization. h. Product Title Holder Transfer Agreement. i. NCNDA/IMFPA. 5. If required buyer may inspect by SGS (Dip Test In Tanks) at buyer's expense. 6. Upon successful verification of POP or Dip Test in the seller's tank, buyer provides Tank Storage Receipt (TSR) to seller in order to issue the scheduled Injection Programming (IP) to be signed by buyer storage facility and then injects the product into buyer's tanks. 7. Buyer makes the payment for the product via MT103, seller transfers the Title Holder & Ownership of the product to the Buyer. 8. After successful Trial Lift (First Lift), Seller issues SPA/Contract for 12 months with R&E to Buyer for processing. 9. Seller pays commissions to all intermediaries involved, for the initial lift and all subsequent lifts according to the signed NCNDA/IMFPA.