Specifications 1.odorless 2.low VOC 3.antimicrobial 4. mildew resistant 5.environmentally friendly 6.waterproof 7.Scrub resistance Description It is an enhanced mildew proof product adopting nano-scale Ag+ antimicrobial and mildew proof technology, integrating odorless formula, with fresh product smell, smooth paint film, durable and beautiful paint.As an affordable and environmentally friendly product with excellent decorative performance, it is characterized by fresh smell, environmental health, strong covering power, large painting area, convenient constructionapplication, short constructionapplication period, etc. Specification Data Solvent: Water Pigment: Non-lead pigment Theoretical Solids By Volume: more than 50% Theoretical Coverage: Theoretically 1 litre of this product covers 12 sqm in 1 coat Coverage varies considerably depending on application methods and surface roughness and porosity. Shelf Life: Minimum 12 months at 77F(25C) unopened and store in cool and dry places. Recommended Film Thickness: Wet: 80 micron Dry: 30 micron Dry Time: At 77F (25C) and 50% R.H. to recoat Touch Dry: 1 hours Recoat : 2-3 hours Application: Brush, Roll, conventional spray or Airless Spray. Thinner: Thin up 15% depend on different application methods & temperature. Do not over thin by adding more than 30% water. Brush or Roller: For sealing new or bare surfaces thin with up to 1 part of clean water to 5-10 parts of paint(10%-20%) Conventional Spray: Add up to 1 part clean water to 5 parts paint(20%) Airless spray: do not thin Clean-up: Clean up equipment with water Typical painting system Substrate System All kinds of Wall surfaces 1.Alkali Resistance Primer (1 coat) 2.Emulsion Wall Paint (2 coats)
Supplier: Brass components ,brass precision part,brass cable glands, brass molding insert,brass stop plugs,brass ppr inserts,brass hardware, brass & metal nozzles,brass nipples, brass sanitary part,brass bush and brass products,brass anchors & fasteners, brass lock nut & check nuts & dome nuts, brass turned components,brass inserts, brass auto parts, brass threaded stud, brass forging components, brass forging metal turning parts, brass shower header wall bracket socket,brass electrical components,brass shower hinges pipe to glass connector,brass shower header clamp,brass knob,brass pipe bush,brass guide bush,brass parts,brass tuned components,brass and metal precision parts,brass,ms,ss elbow fitting,brass terminal box connector,brass tee,brass,ms,ss,aluminium stand off(spacers),brass&ms&aluminium &steel metal adapter,brass&ms & aluminium & steel precision turned components,brass & ms& aluminium & steel & metal nuts, bolts, washers, zinc (zamak,mazak) metal parts, brass & ms, ss, zinc, aluminium
Services: Manufacturer & exporter
we are leading manufacturer & exporter of standoff/spacers as per requirement or Drawing
Supplier: Engineering components for automotive, electrical, construction, transmission tower projects , rail road components hardware like different types of washers, circlips & retaining rings, clips , clamps ,hose clamp , spring band clamps ,metal pressed parts, wire form parts.
Services: Manufacturing & sourcing agents
1. Snap rings 2. Circlips - external & internal 3. E-clips
Spring band clamps of dia 10 mm to 100 mm
1. Nut clamp 2. Nail clamp 3. Shuttering clamp
1. Spring washers 2. Wave washers 3. Plain washers : m.S. , s.S 4. Lock washers : internal & external tooth 5. Copper washer
1. Wire rings 2. Wire clamps 3. Bottle holder 4. Any wire forming component
APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
