Dear buyer--We are known a s a quality brand globally and now offering 2 models for Hair dryer with wattage 1800 and 2200. our body is not plastic body rather it is an ABS material body. Also, we are using copper motor windings which do not heat up and performance of our product is excellent. Please contact us for wholesale qty. Sample facility is available on to pay basis with freight cost to be paid by buyer.
Drum material, European Certificated Stainless Steel AISI 304 Cooling unit supplies automatic cooling down Filtration by front located stainless steel filter Specially designed aluminium fan Specially designed serpentine heaters 600 kg/pes Hydraulically controlled tilting & Pneumatically controlled door opening Control unit with PLC & LCD touch screen panel LG brand PLC, Touch screen Power transmission with special design belt system Power supply is 380 Volt, 3 phase, 50 Hertz Optional Features European Certificated AISI 316 Stainless Steel Rotating door Silicon softening injection system Humidity control unit Natural gas heating Auto cooling for electrical box by air conditioner Dryer mechanices are totally controlled by PLC control unit to command heating, rotating, time and cycle. Tilting hydraulically controlled and door opening pneumatically controlled. Unloading is done by tilting as standard option Steel serpentines, stainless steel drum and cooling unit are standard features as well Dryer machines are totally controlled PLC control unit to command heating, rotating, time and cycle. Tilting hydraulically controlled and door opening pneumatically controlled. Unloading is done by tilting as a standard option. Steel serpentines, stainless steel drum and cooling unit are standard features as well
Supplier: Industrial washing machine and dryers
Buyer: Washing machine.
Dyson Supersonic Hair Dryer
ALTUS AL704 Hair Dryer 2100W
Industrial Dryer
Spray Dryer
Drying and Evaporation Plants
APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
