Epoxy Finish Paint is two-component, polyamide adduct cured, General Purpose Air drying Epoxy Coating. Its Excellent substitute to Enamel.
Supplier: Chemical, chemical raw material, auxiliaries, solvents, paint, coating, rubber, plastic, plasticizer, surfactant, additives, steel pipe, steel tube, stainless steel tube, stainless steel pipe, pipe fitting, flange, fasteners, steel wire, steel accessories
Services: Transportation agent,customs clearance service,
Buyer: Import chemical raw materials, auxiliaries, bulk commodities
Specifications 1.odorless 2.low VOC 3.antimicrobial 4. mildew resistant 5.environmentally friendly 6.waterproof 7.Scrub resistance Description It is an enhanced mildew proof product adopting nano-scale Ag+ antimicrobial and mildew proof technology, integrating odorless formula, with fresh product smell, smooth paint film, durable and beautiful paint.As an affordable and environmentally friendly product with excellent decorative performance, it is characterized by fresh smell, environmental health, strong covering power, large painting area, convenient constructionapplication, short constructionapplication period, etc. Specification Data Solvent: Water Pigment: Non-lead pigment Theoretical Solids By Volume: more than 50% Theoretical Coverage: Theoretically 1 litre of this product covers 12 sqm in 1 coat Coverage varies considerably depending on application methods and surface roughness and porosity. Shelf Life: Minimum 12 months at 77F(25C) unopened and store in cool and dry places. Recommended Film Thickness: Wet: 80 micron Dry: 30 micron Dry Time: At 77F (25C) and 50% R.H. to recoat Touch Dry: 1 hours Recoat : 2-3 hours Application: Brush, Roll, conventional spray or Airless Spray. Thinner: Thin up 15% depend on different application methods & temperature. Do not over thin by adding more than 30% water. Brush or Roller: For sealing new or bare surfaces thin with up to 1 part of clean water to 5-10 parts of paint(10%-20%) Conventional Spray: Add up to 1 part clean water to 5 parts paint(20%) Airless spray: do not thin Clean-up: Clean up equipment with water Typical painting system Substrate System All kinds of Wall surfaces 1.Alkali Resistance Primer (1 coat) 2.Emulsion Wall Paint (2 coats)
DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.
PC natural 100% pure pc without any coating MATERIAL: PC natural 100% pure pc without any coating CATEGORY: PC TYPE: Natural SPECIFICATION: Separate 25 kg bag and Mark per month 78 mt 100% pure pc without any coating ,post Industrial materials Origin: Bangladesh LOADING WEIGHT: 24 Ton FOB (USD/Ton): 1450$ - 1700$ Packaging: Jumbo Bag Est. Shipping Time: 15, 30, 45 days Our Commitment We are committed to delivering in accordance with the quality given, source and licensed in the field of scrap transportation. 2Lians always for the purpose of satisfying customers on the criteria of sustainability and fairness through high work efficiency
Supplier: Electrical materials, electrical equipments, lighting fixtures, plumbing materials, ac materials, it materials, ceiling materials, partition materials, painting materials, floor tiles, hardware materials, hand tools & power tools, garage tools, wooden & carpenter materials, batteries. medical equipment and medical consumable product and medical surgical equipment.
Supplier: Vinyl rolling floor, sports floor, rubber floor, luxury vinyl floor tile, stone plastic floor (spc plank), anti static floor and raised access flooring
Two component, acrylic aliphatic polyurethane coating. Offers excellent gloss and colour retention. It is used for subtracts as steel, aluminum, glass-fiber, plywood etc.
Epoxy Floor Coating (interior Floor Coat) Covered/underground Car Park/garage Warehouse Coatings Factory/food Plant Coating Industrial Floor Coating Self Levelling Floor Coat Hygienic Coating (anti-bacterial)
