Introduction to Instrument PQWT-CL300 series underground pipes water leak detector, is high performance leak detection equipment, has powerful anti-jamming and data processing capabilities, you can make your work easier. It has the following main features. Main Features 1.The use of latest digital signal processing chip and a digital filter chip, 16M cache controller integrated, more responsive. In particular, it can filter with the interference of environmental noise, screening out the leakage noise, allowing the operator to lock leakage points quickly. 2. 7-inch high-definition digital color LCD touch screen with a resolution of 800 * 480, can provide 8 display pages, can show the measurement parameters more clearly and intuitively, and full touch screen design, simple operation. 3. 50 ~ 2500Hz frequency range (spectrum analysis), real-time display of the noise signal distributed on each frequency. 4.Sensor is built-in preamp circuit, using a rubber ring seal and cushion, and the application of professional acoustic methods, making the ability to capture the noise is higher than similar products. 5,Adopt latest noise detecting element, sounds clear. 6.Save 8 sections totaling eight minutes of recording, which is not lost after shut down, could be analyzed at any time. 7.Using a large capacity battery, can work for more than ten hours , and can be removed charging and online charging. 8. Super anti-jamming circuit design, digital signal and analog signal effectively isolate and eliminate the noise generated by the digital circuit . Model No. :PQWT-CL300 Measuring Depth :2 meter Frequency Range: 50-2500HZ Audio Amplifier Gain: Adjustable within the class of 100 Operation Mode :Spectral Analysis,Filter Analysis ,Fine Mode LCD :7-inch Touch Screen Power Supply : 12V 3600mAh Rechargeable Battery
A pipe short nipple is a short length of pipe with threaded ends It is used to connect two pipes or to extend a pipe Description A pipe short nipple is a cylindrical tube with threaded ends The length of the nipple is typically less than 12 inches The diameter of the nipple is typically the same as the diameter of the pipes that it is connecting Technical Specifications The following are some of the technical specifications of a pipe short nipple 1 Size 18 Inch to 4 Inch Customized Up to 12 2 Material Carbon steel Alloy Steel Stainless steel Duplex 3 Thread NPT BSP BSPT Applications Pipe short nipples are used in a variety of applications including A Connecting two pipes B Extending a pipe C Tapping into a pipe D Mounting valves and fittings E Repairing leaks Safety Precautions When working with pipe short nipples it is important to take the following safety precautions a Use the correct size and type of nipple for the application b Do not overtighten the nipples c Use thread sealant to prevent leaks d Be aware of the pressure and temperature ratings of the nipples
A pipe closed nipple is a short, threaded pipe fitting that has closed ends. It is typically used to connect two pipes or to tee off a pipe. Pipe closed nipples are available in a variety of materials, including steel, stainless steel, brass, and plastic. They are also available in a variety of sizes, with the most common sizes being 1/4 inch, 3/8 inch, and 1/2 inch. Here is a technical specification of a pipe closed nipple: 1. Size: 1/8 Inch to 4 Inch Customized Up to 12â?? 2. Material: Carbon steel, Alloy Steel, Stainless steel, Duplex 3. Thread: NPT, BSP, BSPT When choosing a pipe closed nipple, it is important to consider the material, size, thread type, and length. It is also important to make sure that the nipple is compatible with the other components in the system. Here are some additional things to keep in mind when using pipe closed nipples: A. Pipe closed nipples should be tightened to the correct torque specification to prevent leaks. B. Pipe closed nipples should not be used in applications where they will be exposed to high temperatures or corrosive chemicals. C. Pipe closed nipples should be inspected regularly for leaks and damage.
A gate valve is a type of valve that uses a gate or wedge-shaped disc to stop or start the flow of a fluid. The gate is attached to a stem that is operated by a handle or a wheel, and it can be raised or lowered to open or close the valve. When the gate is fully raised, it allows the fluid to flow freely through the valve. When the gate is fully lowered, it blocks the flow of the fluid. Gate valves are widely used in a variety of applications, including oil and gas, chemical processing, water treatment, and power generation. They are available in a range of sizes and materials to suit different applications and fluid types. In China, gate valves are commonly used in industrial piping systems and are designed to meet Chinese national and industry standards. They are known for their reliability, durability, and ease of use, and they are often used in applications where a tight seal is required to prevent leaks. Like JIS flanged ball valves, gate valves are typically connected to the rest of the piping system using flanges, which are fastened together with bolts or other fasteners. The valve body of the gate valve can be made of metal. Such as: forged steel gate valve, stainless steel gate valve, alloy gate valve, bronze gate valve, cast steel gate valve, carbon steel gate valve, etc. Among them, forged steel gate valves are widely used, especially as a cut-off device when the size is greater than 50mm. The main body can also be made of non-metallic materials. For example, ceramic gate valves have good wear resistance and hardness. Some other gate valves are made of special materials, such as Hastelloy gate valves, special steel gate valves and special alloy gate valves. To transport and process strong corrosive media, duplex stainless steel gate valves or super stainless steel gate valves are usually used to alleviate the problem, because they can work well in areas with corrosive environments.
A pipe long nipple is a short length of pipe with threaded ends that is used to connect two pipes or fittings. Pipe long nipples are available in a variety of sizes and thread types to fit different applications. Technical Specifications 1. Size: 1/8 Inch to 4 Inch Customized Up to 12â?? 2. Material: Carbon steel, Alloy Steel, Stainless steel, Duplex 3. Thread: NPT, BSP, BSPT Applications Pipe long nipples are used in a variety of applications, including: a. Connecting two pipes b. Extending a pipe run c. Tapping into a pipe d. Repairing a leaking pipe e. Adding a fitting to a pipe Safety Precautions When working with pipe long nipples, it is important to take the following safety precautions: A. Use the correct size and type of nipple for the application. B. Make sure the nipple is properly threaded and tightened. C. Do not overtighten the nipple, as this could damage the threads. D. Use gloves and eye protection when working with pipe long nipples.
Supplier: Pinhole pipe leak repair clamps, strap type leak repair clamps
Services: Manufacturing and supply
A forged street elbow is a type of pipe fitting that is used to join two pipes at a 90-degree angle. It has a male NPT thread on one end and a female NPT thread on the other. The male thread is screwed into the end of one pipe, and the female thread is screwed into the end of the other pipe. This creates a tight, leak-free connection. Forged street elbows are typically made from carbon steel, stainless steel, or ductile iron. Carbon steel is the most common material, as it is relatively inexpensive and easy to work with. Stainless steel is more expensive, but it is also more corrosion-resistant. Ductile iron is the strongest material, but it is also the most expensive. The technical specifications of a forged street elbow will vary depending on the material, size, and class. The following are some common specifications: Material: Carbon steel, stainless steel, or ductile iron Size: 1/2" to 12" Class: 3000, 6000, or 9000 Thread: NPT, BSP, BSPT
A swage nipple concentric is a type of pipe fitting that is used to connect two pipes of the same diameter. It is made of a single piece of metal that is swaged, or expanded, to fit tightly around the pipes. The swage nipple is then inserted into the pipes and secured with a nut. The technical specifications of a swage nipple concentric vary depending on the size and material of the fitting. However, some common specifications include: 1. Material: Carbon steel, Alloy steel, Stainless steel or Ductile 2. Size: 1/4 inch to 8 inches 3. Schedule: STD, XS, 160, XXS 4. Thread type: NPT, BSP, BSPT 5. Pressure rating: 100 psi to 20,000 psi Swage nipples concentric are commonly used in a variety of applications, including: A. Plumbing B. HVAC C. Fire sprinkler systems D. Pressure vessels E. Industrial piping They are a versatile and reliable type of pipe fitting that can be used in a wide range of conditions. Here are some additional features and benefits of swage nipple concentrics: a. They are easy to install and remove. b. They provide a secure and leak-free connection. c. They are resistant to corrosion and rust. d. They are available in a variety of sizes and materials to meet the needs of different applications.
Product Description A 90 degree elbow is a pipe fitting that is used to change the direction of a pipe by 90 degrees. It is a common fitting that is used in a variety of applications, including plumbing, HVAC, and industrial piping. Technical Specifications The technical specifications of a 90 degree elbow vary depending on the material, size, and type of fitting. However, some of the common specifications include: Material: Steel, brass, copper, plastic, etc. Size: 1/2 inch to 12 inches (nominal pipe size) Type: Butt-weld, threaded, socket-weld, flanged, etc. Radius: Short radius (SR) or long radius (LR) Wall thickness: Schedule 40, Schedule 80, etc. Applications 90 degree elbows are used in a variety of applications, including: Plumbing: Changing the direction of a water pipe HVAC: Changing the direction of an air duct Industrial piping: Changing the direction of a fluid line Machinery: Connecting pipes to valves and other components Construction: Connecting pipes to sprinkler systems and other fixtures Benefits The use of 90 degree elbows in piping systems offers a number of benefits, including: Increased flexibility: Elbows allow pipes to be routed around obstacles and through tight spaces. Reduced stress: Elbows help to reduce stress on pipes by distributing the load more evenly. Improved flow: Elbows can help to improve the flow of fluids by reducing turbulence. Increased safety: Elbows can help to prevent leaks and spills by providing a smooth transition between pipes.
