Raw melting material - aluminum scraps, cans, engine waste etc. Output capacity - 5-30 tons/h, customized Automation - Full automatic/ half automatic (based on output requirement and investment budget Ingot type - ADC12 (7.5kg/ 10kg / customized) 1. After cleaning the oil and grease of waste aluminum, manually put it into the furnace with a forklift; 2. Ignition for melting furnace .Heat up to 680C, and input appropriate proportion of alloy elements. Heat up to 800C, melt and stir evenly, then fetch samples to the spectrometer for testing. Every lot of production need to do testing . 3. Put A tool that attracts iron into the furnace by forklift, to suck away the iron in the aluminum water. 4. Put the slag agent into Alu liquid to remove the slag. After slag removed , put the slags into Aluminum ash separation machine , and let the aluminum water and ash separate. The proportion of slag agent and aluminum liquid is 1:500 5.Open the drain valve and the aluminum water flows automatically to the ingot production line After the ingot casting is completed, the ingot stacking robot will stack the ingots, which means the production is completed.
The third-generation Hastelloy alloy alloy20 is one of the more commonly used components in the C series. Due to its low nickel content, low cost, excellent mechanical and corrosion resistance, it is widely used in pump flow components where corrosion and wear coexist. The solubility of hardness in the ferrite phase reaches its maximum at 850, and as the temperature increases, the solubility increases rapidly and is much smaller than that of the austenite phase. The Cu content in c-276 has exceeded the high solubility in the ferrite phase. The Hastelloy alloy alloy20, formed by a large amount of Ni element composition, is used in industries such as chemical engineering, pharmaceuticals, seawater, fertilizers, and other industries for projects with high corrosion resistance requirements due to its unique characteristics that lie between ferrite and austenite structures, and its resistance to intergranular corrosion. In recent years, the nuclear power industry has developed a corrosion-resistant ability in the operation of power station equipment, which cannot be replaced by other materials. Containing a large amount of Cr component, with high oxidation resistance. The molybdenum element in stainless steel materials is only about 2%, which is far less than the molybdenum content of Hastelloy alloy alloy20. Therefore, high concentration acidity requires the use of materials well. Mainly used, it has the following corrosion resistance properties in oxidation and reduction, and excellent corrosion resistance to most corrosive media. In this oxidizing environment, such as in sulfuric acid manufacturing and solutions containing a large amount of oxidizing ions, it has excellent resistance to pitting corrosion, crevice corrosion, and stress corrosion. Product name ALLOY 20 STAINLESS STEEL Thickness range 0.3mm-3.0mm, Width range 600mm-1500mm Length 2000mm, 2438mm, 3048mm Size 1000mm*2000mm, 1219mm*2438mm, 1219mm*3048mm, or as required Finish No. 1 , No. 4, hairline , 2b, BA, 8K, embossed, PVD color coated, sand blasted, anti-fingerprint Lead time 7 to 15 working days after the receipt Packing Wooden pallet or according to customer's request Application Interior/exterior/architectural/bathroom decoration, elevator decoration, hotel decoration, kitchen equipment, ceiling, cabinet, kitchen sink, advertising nameplate Warehouse Storage Shandong Jintuo Metal Materials Co., Ltd is located in Liaocheng City, the capital of steel tubes. It is a large enterprise specializing in the sales of carbon steel, stainless steel, galvanized color coated products, and copper and aluminum.Our company adopts a flexible business approach and management mechanism to provide good services to customers, while also considering the interests of the owner and the project, in order to ensure the quality of the project.
Use of INCOLOY Alloy 825: 1. The heater is generally used in the oil refining unit; 2. Chemical plant equipment pipeline; 3. Fast cooling cylinder for solid solution used in textile industry; 4. Seamless steel pipe for heat exchanger and condenser. 5. High pressure seamless steel pipe for food (gb-2000) is a high-quality carbon structural steel and alloy steel seamless steel pipe suitable for chemical equipment and pipes with working temperature of - 40~400 �° C and working pressure of 10~30ma. 6. Seamless steel pipes for geological drilling and oil drilling control. 7. Cracking pipe for petrochemical industry is used to transport high-temperature and high-pressure fluid on fertilizer equipment. INCOLOY Alloy 825 Standard Food Grade Sanitary Tube: JIS G3447, KS D 3585, ASTM A270, EN 10357(DIN 11850), AS 1528.1, ISO 2037(NF A49-249) Heat exchanger tube: ASTM A249 / ASME SA249, GB / T 24593-2009, HG 20537.2 Industrial pipe: ASTM A312, EN 10217-7, GB / T 12771-2008, HG 20537.3 Drinking water tube: GB / T 19228 Mechanical tube: ASTM A554, EN 10296-2 Size Outer Diameter Range: 9.5~2000mm Thickness Range: 0.5~20mm (Size can be customized.) Length: Up to 11.8 meters per piece. Shape Section Round, square, rectangular Usage Sanitary tubing: for food processing industry, beverage industry, sugar mill and so on; Heat exchanger tube: condenser, boiler, super heater, evaporator and so on; Industiral pipe: for petroleum delivery, gas delivery, petrochemical industry, wastewater treatment, drainage system, and so on; Mechanical tube: handrail, railings, balustrade, hence and so on. Features: 1.Our stainless steel tubes pipes are treated by bright annealing, inside weld bead removing, precise polishing. The roughness of tubes could be under 0.3�¼m. 2.We have the non destructive testing ( NDT ), eg. online eddy current inspection and hydraulic or airtightness testing. 3. Thick welding, good appearance.The mechanical properties of tube could be tested. 4. And Our tubes are certificated by AD 2000-W0, PED 2014/68/EU, ISO 9001 : 2015. 5. Full material traceability is guaranteed during the manufacturing process. 6. Polished tube is supplied in individual plastic sleeves with capped ends ensuring optimum cleanliness. 7. Internal Bore: Tubes have a smooth, clean and crevice free bore.
We also have interest in selling Bulk Ferro Alloys and especially Low/Medium Carbon Silico Manganese and we are already exporting these product/s. We have tied up with a manufacturer bin , Bhutan to sell their products. Products are:- Low Carbon Silico Manganese. Typical Specifications are: Mn: 55 % Minimum Si: 25-28% C: 0.2% Maximum P: 0.15% Maximum Size: 10-150 MM (90%) Medium Carbon Silico Manganese. Typical Specifications are: - Mn: 55%-60% Si: 22%-25% Max C: 0.5% Max Si: 0.05% Max P: 0.2%-0.40% Size: 10-150 MM (90%) For sure, we will be able to meet the requirements, once we get your reply
Alloy 20 is an austenitic nickel-iron-chromium alloy with outstanding corrosion resistance. Alloy 20 Olets provide strong sulfuric acid resistance. This alloy is also resistant to phosphoric acid, nitric acid, and aqueous salt solutions. Alloy 20 Olets are an excellent choice when chloride stress corrosion cracking is a concern since they resist pitting and crevice corrosion. Because the rate of corrosion can substantially increase in chloride ion-containing environments, caution should be exercised. Alloy 20 Olets may provide cost savings while outperforming typical stainless steels when compared to higher nickel-based alloys. Alloy 20 is a super-austenitic stainless steel that was developed for maximum corrosion resistance to sulfuric acid and other extreme environments where regular austenitic grades are ineffective. Hot-working and cold-working are two traditional ways of producing Alloy 20. Itâ??s also vital to determine whether or not the desired corrosion resistance can be achieved in a given environment. Alloy 20 is used in a variety of industries, including chemical processing, petrochemical and refining, marine, pharmaceutical, and food processing. End-use applications include storage tanks, mixing tanks, agitators, pump and valve parts, food processing equipment, fasteners, and fittings. Plastics and synthetic fiber manufacturing Equipment for chemical and petroleum processing, heat exchangers, and process piping
Incoloy 825 is a nickel iron chromium alloy, which is widely used in petroleum, natural gas and chemical processing industries. It has good corrosion resistance and can operate at higher temperatures than most stainless steels. Incoloy 825 is a completely austenitic nickel iron chromium alloy, stabilized by titanium and added with copper and molybdenum. Incoloy 825 is a general engineering alloy, which is resistant to acid and alkali metal corrosion in oxidation and reduction environments. The Incoloy825 has the following functions: Good resistance to stress corrosion cracking. Good resistance to pitting and crevice corrosion Good oxidation resistance and non oxidative thermal acidity. It has good mechanical properties at room temperature and high temperature up to 550 Certification of pressure vessels with manufacturing temperatures up to 450 C Incoloy 825 metallographic structure: Incoloy 825 alloy has a stable face centered cubic structure. Chemical composition and appropriate heat treatment ensure that the corrosion resistance will not be weakened by sensitization. Incoloy825 Corrosion resistance: Incoloy825 is a general engineering alloy, which is resistant to acid and alkali metal corrosion in oxidation and reduction environments. Incoloy825 is widely used in various industrial fields where the working temperature is no more than 550. Typical applications include: Heating pipes, containers, baskets and chains for sulfuric acid pickling plants. Seawater cooling heat exchanger, marine product pipeline system, acid gas environment pipeline. Heat exchanger, evaporator, washing, immersion tube, etc. In phosphoric acid production. Air heat exchanger in petroleum refining Food Engineering chemical process Flame retardant alloy for high-pressure oxygen Product name INCOLOY Alloy 825 Grade INCOLOY Alloy 825 Thickness range 0.3mm-3.0mm, Width range 600mm-1500mm Length 2000mm, 2438mm, 3048mm Size 1000mm*2000mm, 1219mm*2438mm, 1219mm*3048mm, or as required Finish No. 1 , No. 4, hairline , 2b, BA, 8K, embossed, PVD color coated, sand blasted, anti-fingerprint Lead time 7 to 15 working days after the receipt Packing Wooden pallet or according to customer's request Application Interior/exterior/architectural/bathroom decoration, elevator decoration, hotel decoration, kitchen equipment, ceiling, cabinet, kitchen sink, advertising nameplate Grade Cu Ti AI P C Ni Cr Mo INCOLOY Alloy 825 2 0.8 0.1 - 0.02 42 21 3
We are proactive organization Specialist in Stainless Steel Pipes and other quality products that meet and exceed customer`s specific requirements and thus ensure complete satisfaction. We are capable of providing a vast range of materials like stainless steel, Carbon Steel & Alloy Steel Pipe Fittings from stock, to suit your needs. Products Stainless Steel Products Nickel Alloys Nickel Aluminum Bronze (NAB) Copper Nickel (Cu/Ni) Hydraulic Pipes Stainless Steel Balls Stainless Steel Stem Duplex Steel Sheet / Rods Super Duplex Steel Sheet / Rods Valve Component
Exotic Metal Alloys is one of the Nickel Alloy 200 Round Bars are made by utilizing the prominent nature of nickel amalgam that is sourced from extraordinary 'ol structured show shippers. In any case, the improvement being picked up is imagining a key ground in plan out the stunning thought of the thing. The thing is passed on Nickel Alloy 200 Round Bars are made by using mind blowing nature of nickel amalgam that is sourced from ensured show vendors. In any case, the improvement being made is driving forward through a mammoth headway in plan out the dazzling thought of the thing. The thing is passed on by using groupings of present day mechanical social gatherings and contraption paying little character to foul material quality measures to make possibly what an application has the choice to have. In like manner, standard stage devastating graph is done that considers quality control and probability being made parts. Keeping structures and spending plan, the industry is driving the thing in various examinations, subtleties and at reasonable rates.
Exotic Metal Alloys Monel K-500 Bars, These bars are the amazing idea of restricting use and scratched spot. It denies any wear in tear around its surface. Round bars are treated with various cementing process so that these are indestructible in any condition. Its unmatched insane quality makes it perfect for liberal managing application. Bars counter any weight and setting parts. With no affirming and beating these bars stays against fluctuating loads. Monel bars are completely made game plans for working in high-temperature condition for discrediting any bowing. We gives confinement in bars some of them are H8, H9, H10, H11, H12, H13K9, K10, K11, and K12. Estimations are length 1 to 6 meters, broadness ranges from 0.1 to 100 mm. hex, square, round, square shape, billet are a few conditions of these bars.
Copper scrap wire 1.Product name : copper scrap 2.wire from copper cables 3.clean,red,99.9% 1.name:copper wire scrap 99.99 2.copper content:99.95% min 3.material: copper 4.copper scrap/pallet Material : quality brass wire Wire diameter: 0.30mm, 0.25mm, 0.20mm Weight/spool: 3 kg, 5 kg, 7 kg, 15 kg, 20kg Tensile strength: 1000 N/mm2, 900 N/mm2, 500 N/mm2, 450 N/mm2, N/mm2 5.Packing: shrink wrapped+carton+pallet to resist moisture, quake, and corrosion. 6.We could supply the copper scrap with high quality and competitive price. 1) Our copper scrap includes wires, tubes, and plates, etc. 2)The size is chips or other. 3) Copper content could neet customers need. Copper wire scrap at 99% purity. Insulation removed through burning. Copper wire scrap at 96% purity. Insulation removed through burning. 7.Application: Electrical, light industry, machinery, building industry, national defense industry Copper Scrap is industry a important sources of the raw materials All kinds of can be recycled Recycling waste production with copper
