Specifications 1.odorless 2.low VOC 3.antimicrobial 4. mildew resistant 5.environmentally friendly 6.waterproof 7.Scrub resistance Description It is an enhanced mildew proof product adopting nano-scale Ag+ antimicrobial and mildew proof technology, integrating odorless formula, with fresh product smell, smooth paint film, durable and beautiful paint.As an affordable and environmentally friendly product with excellent decorative performance, it is characterized by fresh smell, environmental health, strong covering power, large painting area, convenient constructionapplication, short constructionapplication period, etc. Specification Data Solvent: Water Pigment: Non-lead pigment Theoretical Solids By Volume: more than 50% Theoretical Coverage: Theoretically 1 litre of this product covers 12 sqm in 1 coat Coverage varies considerably depending on application methods and surface roughness and porosity. Shelf Life: Minimum 12 months at 77F(25C) unopened and store in cool and dry places. Recommended Film Thickness: Wet: 80 micron Dry: 30 micron Dry Time: At 77F (25C) and 50% R.H. to recoat Touch Dry: 1 hours Recoat : 2-3 hours Application: Brush, Roll, conventional spray or Airless Spray. Thinner: Thin up 15% depend on different application methods & temperature. Do not over thin by adding more than 30% water. Brush or Roller: For sealing new or bare surfaces thin with up to 1 part of clean water to 5-10 parts of paint(10%-20%) Conventional Spray: Add up to 1 part clean water to 5 parts paint(20%) Airless spray: do not thin Clean-up: Clean up equipment with water Typical painting system Substrate System All kinds of Wall surfaces 1.Alkali Resistance Primer (1 coat) 2.Emulsion Wall Paint (2 coats)
Epoxy Finish Paint is two-component, polyamide adduct cured, General Purpose Air drying Epoxy Coating. Its Excellent substitute to Enamel.
Product Description: Short Oil Alkyd Resin, which find application in nitrocellu-lose based automotive refinishes as a plasticizer and as a binder for stoving finishes in combination with butylated melamine formaldehyde resin. Origin: INDIA Key Specification: "Solids content: 70± 2% Color - Gardner Scale : 2 max (50% solution inXylene) Acid number: 10 max.(mg KOH/g - solids) Viscosity: 10-15 Poise at 25°C in 50% Xylene" Minimum Order Size/ Packgaing details: 1 FCL (20MT)/ 200 KG BARREL
DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.
Paint Emulsions We supply wide variety of premium quality water based emulsions for the paint industry. The emulsions are selected based on the applications depending on interior or exterior paint formulation. We also supply paint aids such as thickeners and dispersing agents which are mostly performance polymers used in manufacturing good quality water based Acrylic Paints.
Silicone Emulsion 60% is used in industrial applications such as in Rubber and plastics as release agents and lubricants, in Food trays and plastic serving dishes as release agents, in Car polishes and household cleaners to improve protection, resistance, gloss and spread ability and in Textile finishing to enhance feel, water repellency and reduce the need for ironing. Silicone Emulsion 60% is also used in Perlite, vermiculite and clay and other building materials to improve water repellency and protect against dampness. Itâ??s used in Printing and papermaking for lubrication and as an antistatic agent. Silicone Emulsion 60% used as a Release agent for industrial rubber tire plastics and casting materials; Rotary offset printing lubricant; Industrial waterproofing agent and release agent; Additives for maintenance products; Polishing agent for floors and furniture; And Leather maintenance products, etc. Silicone Emulsion 60% WC Code: 24-005-04 Sales Specification Appearance: White Liquid Odour: Characterictic Solid content (%): 60.00 �± 2.0 pH Value: 8.0 �± 1.0 Density (g/cm3): 0.953 �± 0.02 Soluble in water: Miscible Packing 440.92 LB Drum 2204.60 LB IBC Tote
Water Based Coatings - Primers, Gloss & High Scuff - High Gloss/High Slip - Duct Gloss & Matt - Specialty Coatings - Soft Feel / Satin / Neutral / Super Matt
Water Based Acrylic Resin Emulsions for Printing Inks & Varnishes We supply ecoprint range of water based acrylic resin for high gloss water based printing Inks and Varnishes. Our ecoprint range of acrylic resins are REACH / ROHS compliant, Formaldehyde free, APEO free, PVC free, Phthalate free and Azo dyes free.
Textile Emulsions We have a broad range of coating products for the TEXTILE INDUSTRY such as Textile finishing agents Strech khadi for hosiery textile printing Ready khadi for textile printing Excellent quality binders for textile printing High quality plastisols
