Specifications:
Media: Air (dry or lubricated)
Non-corrosive gas or light hydraulic oil
Construction: Suitable for indoor or outdoor installation
Material: Housing - Aluminium Alloy
Drive Shaft: Carbon Steel
Finish: Yellow Colour Powder Coated Rotation (Standard)
Counter clockwise to open with port 'A' pressurised
Spring return Actuators air fail to close clockwise
Lubrication: Factory lubricated for the normal life of Actuators
Actuator Model AT pneumatic actuator
Actuator Material Aluminium Alloy
Action double-Â acting, single acting normally closed, single acting normally open
Rotary Angle: 90
Output Torque : 6.2NM-4944NM
Cylinder  Size 32mm-270mm
Air Pressure 4~8bar
Working Temperature -20C~+80C
Standard GB/ISO/DIN
* We manufacture a wide range of Process Ball Valves in single, two, and three-piece constructions.The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements.
* The valves are of floating-ball design where the ball moves towards the downstream seat,
under pressure, to effect a tight seal.Trunnion-mounted Ball Valve design complies to API 6D
* Wide portfolio of Side-entry and Top-entry designs
* Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH
* Firesafe design - to API 607 and API 6FA
* CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU,
Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required
* Double block and bleed (DBB) feature - Valves are designed and tested for automatic
* cavity relief
* Anti-blowout stem design
* Coil springs used for consistent seat loading and lower operating torque
* Lip seals provided for low temperature services
* Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary)
* Wide portfolio of Side-entry and Top-entry designs
* Options: Buried service, Cryogenic
* Offered with Electric, Pneumatic and Hydraulic Actuators
* In-house Tests Capabilities
* Fire-safe to ISO 10497 and API 607
* Mirror-finished solid stainless ball
* Fine-grained PTFE seats
* Cavity Pressure Relief mechanism
* Blowout-proof stem
* High integrity stem sealing â?? Belleville springs compensate for wear and thermal expansions
* Size 2" to 56" (50 mm to 1400 mm)
* ASME Class Class 150 to 2500
* Design Standard API 6D
* Size ¼" to 8" (8 mm to 200 mm)
* ASME Class Class 150 to 2500
* Design Standard ISO 17292, API 608, API 6D
* Antistatic feature
* Actuator-mounting flange conforms to ISO 5211
* Single, two and three piece constructions
* Full-bore and regular-bore designs
* Soft and metal-seated
* Offered in carbon steel, stainless steel and duplex stainless steels
The butterfly plate of the butterfly valve is installed in the diameter direction of the pipe. In the cylindrical channel of the butterfly valve body, the disc shaped butterfly plate rotates around the axis with a rotation angle of 0 �°~90 �°. When the rotation angle reaches 90 �°, the valve is fully open.
The butterfly valve is simple in structure, small in volume and light in weight, and only consists of a few parts. Moreover, the valve can be quickly opened and closed only by rotating 90 �°, which is simple to operate. At the same time, the valve has good fluid control characteristics. When the butterfly valve is in the fully open position, the thickness of the butterfly plate is the resistance when the medium flows through the valve body, so the pressure drop generated by the valve is very small, so it has good flow control characteristics. The butterfly valve has two sealing types: elastic seal and metal seal. For elastic sealing valves, the sealing ring can be embedded on the valve body or attached to the periphery of the butterfly plate.
The valve with metal seal is generally longer than the valve with elastic seal, but it is difficult to achieve complete sealing. The metal seal can adapt to higher working temperature, while the elastic seal has the defect of being limited by temperature.
If the butterfly valve is required to be used for flow control, the main thing is to correctly select the size and type of the valve. The structure principle of butterfly valve is especially suitable for making large diameter valves. Butterfly valves are not only widely used in petroleum, gas, chemical industry, water treatment and other general industries, but also used in the cooling water system of thermal power plants.
There are two kinds of butterfly valves commonly used: wafer type butterfly valve and flange type butterfly valve. Wafer type butterfly valve uses stud bolts to connect the valve between two pipe flanges. Flange type butterfly valve has flanges on the valve, and bolts are used to connect the flanges on both ends of the valve to the pipe flanges.
T-pav903 serie: valve body:stainless steel, valve connection:screwed, valve way:2/2 and actuator double acting or single acting types.
Da:actuator double acting , sr:actuator single acting .
Application:water, air, hot water, steam, oil, aggresive media, gas, foot industry, chemical industry,
Tork actuator features body extruted.Aluminium, hard anodized
Caps die cast aluminium, electrostatic painted
Pistons die cast aluminium
Supp.Air 4-6 bar
Ball valve body full borei, aisi 316 stainless steel and 3 parts body
Way: two way.
O-ring ptfe
Pressure suitable low and high pressure.
Temperature -20....140 c degree
Working pres. Pn 40 bar(1/2"..11/4") , 16 bar(11/2"...3")
Test bntnall valves are tested 48 hour, at 20 barda
Europe is a leading manufacturer of pneumatically operated ball valves in . For its operation, a pneumatic ball valve is paired with a pneumatic actuator. It's a tough valve that shuts off perfectly. It can also be employed for fine media flow in throttling applications. Europe offers high quality Pneumatic Ball Valves with a long service life. This type of valve ensures a secure shutdown.
Features of Pneumatic Actuated Ball Valve
It has both sides seals coated with internal balls and can deliver tight cut-off even after years of operation, according to Pneumatic Actuated Ball Valve features.
The ability to open and close quickly.
The actuator is small.
Are you seeking for a reputable manufacturer of pneumatic ball valves
With our manufacturing facility and warehouse in , we are one of the leading pneumatic ball valve manufacturers in . We are primarily concerned with achieving complete customer loyalty through the provision of dependable, high quality industrial valves. We produce valves that are cost effective without sacrificing quality.
Available materials CF8M, CF8, SS316, CF8M, WCB, WC6, WCC, LCB, LCC, SS304, SS316
Class 150 to 2500
Nominal Pressure PN6 to PN450
Size 12 to 48
Ends Flanged, Buttweld, Socket weld, Threaded.
Operation Pneumatic Actuated
For more details visit here: https://www.valvesonlyeurope.com/product-category/pneumatic-actuated-ball-valve/
