Rudra Enterprise

We deals in the following products :- 1) PVC Resin 2) Caustic Soda Flakes

1 108-78-1 Melamine 2 37640-57-6 Melamine cyanurate 3 63428-83-1 Polyamide 4 106-50-3 1,4-phenylenediamine 5 9002-89-5 Poly(vinyl alcohol) 6 105-60-2 �µ-caprolactam 7 10578-34-4 Stearyl benzoate 8 108-31-6 Maleic anhydride 9 108-05-4 Vinyl acetate 10 26264-06-2 Calcium dodecylbenzene sulfonate 11 111-69-3 Adiponitrile 12 924-42-5 N-Methylolacrylamide 13 100-20-9 Terephthaloyl Chloride 14 99-63-8 Isophthaloyl Chloride 15 1338-02-9 Copper naphthenate 16 6153-56-6 Oxalic acid dihydrate 17 79-10-7 Acrylic acid 18 75-01-4 Chloroethene 19 25190-06-1 Poly(butylene oxide) macromolecule 20 77-99-6 Trimethylol propane

DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.

1 101-68-8 4,4'-Diphenylmethane diisocyanate 2 9016-00-6 Poly(dimethylsiloxane) 3 26471-62-5 Tolylene diisocyanate 4 100-42-5 Styrene 5 141-32-2 Butyl acrylate 6 107-13-1 Acrylonitrile 7 106-99-0 Buta-1,3-diene 8 75-38-7 1,1-difluoroethylene 9 9-38-9 Chlorotrifluoroethylene 10 111-44-4 2,2'-Dichlorodiethyl ether 11 1187-93-5 Trifluoromethyl trifluorovinyl ether 12 21645-51-2 Aluminum hydroxide 13 116-14-3 Tetrafluoroethene 14 116-15-4 Hexafluoropropylene 15 126-99-8 Chloroprene 16 103-11-7 2-Ethylhexyl acrylate 17 140-88-5 Ethyl acrylate 18 78-79-5 Isoprene 19 96-33-3 Methyl acrylate 20 1300-21-6 Dichloroethane

We are glad to propose 500 MT of stain less steel mill scale. Mill scale is formed on the outer surfaces during by the hot rolling lamination of stainless-steel products. At a visual inspection the material is a hard brittle sand and is mainly composed of iron oxides, mostly ferric, and is bluish black in colour, but it also contains considerable alloying elements such as chromium and nickel. The recovery ratio after melting in furnace for the most valuable alloy elements is: - Ni: 3.5 - 4.5% - Cr: 6-8% From the chemical and physical analysis performed on the scrap, and according to the European environmental rules, the material has been classified as a special non dangerous waste, listed in green list. In particular the mill scale can be classified as follows: Waste code: 10 02 10 The material is stored on cemented flooring, and it can be loaded loose in tipper trucks or containers. Chemical analysis of the material is available on request.